ElphelWiki - User contributions [en]

Talk:10349

2007-11-01T03:17:47Z

Dimon:

About the plex panel for developer case: why do it transparent ? Is where a special reason ? It's not very good for image quality to have light inside the case. --[[User:Polto|Polto]] 11:36, 14 October 2007 (GMT)

Transparent? Why? Is it written anywhere?--[[User:Andrey.filippov|Andrey.filippov]] 16:29, 14 October 2007 (CDT)

Yep, in [[10349#Body_of_camera_for_developers]] --[[User:Polto|Polto]] 08:55, 15 October 2007 (GMT)

I looked at the images only, did not read the text. You are right there is no sense to have transparent cover - it will allow stray light to reach the sensor.--[[User:Andrey.filippov|Andrey.filippov]] 03:10, 15 October 2007 (CDT)

No problem, we can use black plex.
--[[User:Dimon|dimon]] 21:11, 16 October 2007 (CDT)

Will the RS323 socket fit in the camera on top of both 10353 & 10349 ?
--[[User:Polto|Polto]] 03:45, 1 November 2007 (GMT)

Should be yes. I measure distance between PCB of 10349 with 10353 to top of cover on 3D model. This is 11.5 mm. For common socket of RS232 this distance is good.

That is my comment. --[[User:Dimon|dimon]] 22:17, 31 October 2007 (CDT)

Talk:10349

2007-11-01T02:59:43Z

Dimon:

10349

2007-10-31T22:47:30Z

Dimon:

Russia page [[10349.Ru]]

[[Image:10349RevC.jpg|thumb|Elphel 10349RevC boaard]]
[[Image:IDE-HD-1.8p.jpg|thumb|1.8" IDE HD with zif connector]]
[[Image:10349RevCon10353.jpg|thumb|10349 RevC mounted on 10353]]
=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Connector pinouts ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J7 pin layout (1 is marked)

(GND) (RX)
5 3 1
6 4 2
(TX)

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

==== Power consumption in different configurations ====

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

<table border="1">
<tr><td>2400 milliwatts</td><td>just booted</td></tr>
<tr><td>3000 milliwatts</td><td>after setting image parameters</td></tr>
<tr><td>3700 milliwatts</td><td>streamer on</td></tr>
<tr><td>3300 milliwatts</td><td>streamer off</td></tr>
<tr><td>3800 milliwatts</td><td>streamer on and somebody playing the stream</td></tr>
<tr><td>5000 milliwatts</td><td>with streamer on and HD writing at full speed (dd)</td></tr>
<tr><td>5800 milliwatts</td><td>streamer on, HD and USB-flash writing at full speed</td></tr>
<tr><td>3300 milliwatts</td><td>back to streamer off</td></tr>
</table>

Tests was performed with [http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1130276637958&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3795822279B15 Linksys SRW224P] POE switch

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

=== Body of camera for developers ===

Case A consist of a large window on the top and transparent clear plastic panel for closing. Anybody can
easy modified this panel for any application.

Case B consists of a large space with two bodies. Can use same as back panel can use for backpanel clear plastic too.

[[Image:Devbody-1.png|thumb|Body for developers kit A]]
[[Image:Devbody-2.png|thumb|Body for developers kit B]]

[[Image:Developer-body-1_1.png|thumb|Body for developers kit other of A]]
[[Image:Developer-body-2_1.png|thumb|Body for developers kit other of B]]
[[Image:Developer-body-3_1.png|thumb|Body for developers kit other of C]]

[[Image:Developer-body-1_3.png|thumb|Body for developers kit other of A]]
=== Another version of a "developer" camera body ===
Here are the rendered 3d-image and the source files [[Image:Assembly200709-developer_af01.png]]

With socket for serial

[http://wiki.elphel.com/index.php?title=Image:Developer_af_1_1.tar.gz 3D design files]

[[Image:Assembly200709-developer_af01-1.png|thumb|With socket for serial.]]

With socket for serial and IO ports
[http://wiki.elphel.com/index.php?title=Image:Developer_af_1_2.tar.gz 3D design files]

[[Image:Assembly200709-developer_af01-2.png|thumb|With socket for serial and IO ports.]]

Other variant with socket for serial. [http://wiki.elphel.com/index.php?title=Image:Developer_af_1_3.tar.gz 3D design files]

[[Image:Assembly200709-developer_af01-3.png|thumb|With socket for serial.]]

=== New version of a "developer" camera body ===

[[Image:Assembly200709-developer_af01-4.png|thumb|With socket for serial.]]

Design files [http://wiki.elphel.com/index.php?title=Image:Developer_af_1_4.tar.gz 3D design files]

Socket with screw [[Image:Serial.jpg|thumb|Socket with screw.]]

File:Developer af 1 4.tar.gz

2007-10-31T22:45:16Z

Dimon:

File:Serial.jpg

2007-10-31T22:44:20Z

Dimon:

File:Assembly200709-developer af01-4.png

2007-10-31T22:41:33Z

Dimon:

10349

2007-10-29T22:52:46Z

Dimon:

File:Developer af 1 3.tar.gz

2007-10-29T22:51:11Z

Dimon:

File:Assembly200709-developer af01-3.png

2007-10-29T22:47:02Z

Dimon:

File:Developer af 1 2.tar.gz

2007-10-29T04:35:09Z

Dimon:

10349

2007-10-29T04:34:37Z

Dimon:

File:Developer af 1 1.tar.gz

2007-10-29T04:31:58Z

Dimon:

10349

2007-10-29T04:31:13Z

Dimon:

Russia page [[10349.Ru]]

[[Image:10349RevC.jpg|thumb|Elphel 10349RevC boaard]]
[[Image:IDE-HD-1.8p.jpg|thumb|1.8" IDE HD with zif connector]]
[[Image:10349RevCon10353.jpg|thumb|10349 RevC mounted on 10353]]
=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Connector pinouts ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J7 pin layout (1 is marked)

(GND) (RX)
5 3 1
6 4 2
(TX)

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

==== Power consumption in different configurations ====

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

<table border="1">
<tr><td>2400 milliwatts</td><td>just booted</td></tr>
<tr><td>3000 milliwatts</td><td>after setting image parameters</td></tr>
<tr><td>3700 milliwatts</td><td>streamer on</td></tr>
<tr><td>3300 milliwatts</td><td>streamer off</td></tr>
<tr><td>3800 milliwatts</td><td>streamer on and somebody playing the stream</td></tr>
<tr><td>5000 milliwatts</td><td>with streamer on and HD writing at full speed (dd)</td></tr>
<tr><td>5800 milliwatts</td><td>streamer on, HD and USB-flash writing at full speed</td></tr>
<tr><td>3300 milliwatts</td><td>back to streamer off</td></tr>
</table>

Tests was performed with [http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1130276637958&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3795822279B15 Linksys SRW224P] POE switch

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

=== Body of camera for developers ===

Case A consist of a large window on the top and transparent clear plastic panel for closing. Anybody can
easy modified this panel for any application.

Case B consists of a large space with two bodies. Can use same as back panel can use for backpanel clear plastic too.

[[Image:Devbody-1.png|thumb|Body for developers kit A]]
[[Image:Devbody-2.png|thumb|Body for developers kit B]]

[[Image:Developer-body-1_1.png|thumb|Body for developers kit other of A]]
[[Image:Developer-body-2_1.png|thumb|Body for developers kit other of B]]
[[Image:Developer-body-3_1.png|thumb|Body for developers kit other of C]]

[[Image:Developer-body-1_3.png|thumb|Body for developers kit other of A]]
=== Another version of a "developer" camera body ===
Here are the rendered 3d-image and the source files [[Image:Assembly200709-developer_af01.png]]

With socket for serial
[[Image:Assembly200709-developer_af01-1.png|thumb|With socket for serial.]]

With socket for serial and IO ports
[[Image:Assembly200709-developer_af01-2.png|thumb|With socket for serial and IO ports.]]

File:Assembly200709-developer af01-2.png

2007-10-29T04:27:30Z

Dimon:

File:Assembly200709-developer af01-1.png

2007-10-29T04:27:06Z

Dimon:

10349

2007-10-26T08:20:55Z

Dimon:

Russia page [[10349.Ru]]

[[Image:10349RevC.jpg|thumb|Elphel 10349RevC boaard]]
[[Image:IDE-HD-1.8p.jpg|thumb|1.8" IDE HD with zif connector]]
[[Image:10349RevCon10353.jpg|thumb|10349 RevC mounted on 10353]]
=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Connector pinouts ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J7 pin layout (1 is marked)

(GND) (RX)
5 3 1
6 4 2
(TX)

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

==== Power consumption in different configurations ====

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

<table border="1">
<tr><td>2400 milliwatts</td><td>just booted</td></tr>
<tr><td>3000 milliwatts</td><td>after setting image parameters</td></tr>
<tr><td>3700 milliwatts</td><td>streamer on</td></tr>
<tr><td>3300 milliwatts</td><td>streamer off</td></tr>
<tr><td>3800 milliwatts</td><td>streamer on and somebody playing the stream</td></tr>
<tr><td>5000 milliwatts</td><td>with streamer on and HD writing at full speed (dd)</td></tr>
<tr><td>5800 milliwatts</td><td>streamer on, HD and USB-flash writing at full speed</td></tr>
<tr><td>3300 milliwatts</td><td>back to streamer off</td></tr>
</table>

Tests was performed with [http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1130276637958&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3795822279B15 Linksys SRW224P] POE switch

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

=== Body of camera for developers ===

Case A consist of a large window on the top and transparent plex panel for closing. Anybody can
easy modified this panel for any application.

Case B consist a large space with two bodies. Can use same as back pannel can use for backpanel plex too.

[[Image:Devbody-1.png|thumb|Body for developers kit A]]
[[Image:Devbody-2.png|thumb|Body for developers kit B]]

[[Image:Developer-body-1_1.png|thumb|Body for developers kit other of A]]
[[Image:Developer-body-2_1.png|thumb|Body for developers kit other of B]]
[[Image:Developer-body-3_1.png|thumb|Body for developers kit other of C]]

[[Image:Developer-body-1_3.png|thumb|Body for developers kit other of A]]

File:Developer-body-1 3.png

2007-10-26T08:20:08Z

Dimon:

10349

2007-10-17T23:32:26Z

Dimon:

Russia page [[10349.Ru]]

[[Image:10349RevC.jpg|thumb|Elphel 10349RevC boaard]]
[[Image:IDE-HD-1.8p.jpg|thumb|1.8" IDE HD with zif connector]]
[[Image:10349RevCon10353.jpg|thumb|10349 RevC mounted on 10353]]
=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Connector pinouts ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J7 pin layout (1 is marked)

(GND) (RX)
5 3 1
6 4 2
(TX)

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

==== Power consumption in different configurations ====

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

<table border="1">
<tr><td>2400 milliwatts</td><td>just booted</td></tr>
<tr><td>3000 milliwatts</td><td>after setting image parameters</td></tr>
<tr><td>3700 milliwatts</td><td>streamer on</td></tr>
<tr><td>3300 milliwatts</td><td>streamer off</td></tr>
<tr><td>3800 milliwatts</td><td>streamer on and somebody playing the stream</td></tr>
<tr><td>5000 milliwatts</td><td>with streamer on and HD writing at full speed (dd)</td></tr>
<tr><td>5800 milliwatts</td><td>streamer on, HD and USB-flash writing at full speed</td></tr>
<tr><td>3300 milliwatts</td><td>back to streamer off</td></tr>
</table>

Tests was performed with [http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1130276637958&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3795822279B15 Linksys SRW224P] POE switch

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

=== Body of camera for developers ===

Case A consist of a large window on the top and transparent plex panel for closing. Anybody can
easy modified this panel for any application.

Case B consist a large space with two bodies. Can use same as back pannel can use for backpanel plex too.

[[Image:Devbody-1.png|thumb|Body for developers kit A]]
[[Image:Devbody-2.png|thumb|Body for developers kit B]]

[[Image:Developer-body-1_1.png|thumb|Body for developers kit other of A]]
[[Image:Developer-body-2_1.png|thumb|Body for developers kit other of B]]
[[Image:Developer-body-3_1.png|thumb|Body for developers kit other of C]]

File:Developer-body-3 1.png

2007-10-17T23:31:36Z

Dimon:

Talk:10349

2007-10-17T02:11:49Z

Dimon:

10349

2007-10-16T22:41:56Z

Dimon:

Russia page [[10349.Ru]]

[[Image:10349RevC.jpg|thumb|Elphel 10349RevC boaard]]
[[Image:IDE-HD-1.8p.jpg|thumb|1.8" IDE HD with zif connector]]
[[Image:10349RevCon10353.jpg|thumb|10349 RevC mounted on 10353]]
=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Connector pinouts ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

==== Power consumption in different configurations ====

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

<table border="1">
<tr><td>2400 milliwatts</td><td>just booted</td></tr>
<tr><td>3000 milliwatts</td><td>after setting image parameters</td></tr>
<tr><td>3700 milliwatts</td><td>streamer on</td></tr>
<tr><td>3300 milliwatts</td><td>streamer off</td></tr>
<tr><td>3800 milliwatts</td><td>streamer on and somebody playing the stream</td></tr>
<tr><td>5000 milliwatts</td><td>with streamer on and HD writing at full speed (dd)</td></tr>
<tr><td>5800 milliwatts</td><td>streamer on, HD and USB-flash writing at full speed</td></tr>
<tr><td>3300 milliwatts</td><td>back to streamer off</td></tr>
</table>

Tests was performed with [http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1130276637958&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3795822279B15 Linksys SRW224P] POE switch

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

=== Body of camera for developers ===

Case A consist of a large window on the top and transparent plex panel for closing. Anybody can
easy modified this panel for any application.

Case B consist a large space with two bodies. Can use same as back pannel can use for backpanel plex too.

[[Image:Devbody-1.png|thumb|Body for developers kit A]]
[[Image:Devbody-2.png|thumb|Body for developers kit B]]

[[Image:Developer-body-1_1.png|thumb|Body for developers kit other of A]]
[[Image:Developer-body-2_1.png|thumb|Body for developers kit other of B]]

File:Developer-body-2 1.png

2007-10-16T22:39:28Z

Dimon:

File:Developer-body-1 1.png

2007-10-16T22:39:00Z

Dimon:

10349

2007-10-12T14:27:57Z

Dimon:

Russia page [[10349.Ru]]

[[Image:10349RevC.jpg|thumb|Elphel 10349RevC boaard]]
[[Image:IDE-HD-1.8p.jpg|thumb|1.8" IDE HD with zif connector]]
[[Image:10349RevCon10353.jpg|thumb|10349 RevC mounted on 10353]]
=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Connector pinouts ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

==== Power consumption in different configurations ====

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

<table border="1">
<tr><td>2400 milliwatts</td><td>just booted</td></tr>
<tr><td>3000 milliwatts</td><td>after setting image parameters</td></tr>
<tr><td>3700 milliwatts</td><td>streamer on</td></tr>
<tr><td>3300 milliwatts</td><td>streamer off</td></tr>
<tr><td>3800 milliwatts</td><td>streamer on and somebody playing the stream</td></tr>
<tr><td>5000 milliwatts</td><td>with streamer on and HD writing at full speed (dd)</td></tr>
<tr><td>5800 milliwatts</td><td>streamer on, HD and USB-flash writing at full speed</td></tr>
<tr><td>3300 milliwatts</td><td>back to streamer off</td></tr>
</table>

Tests was performed with [http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1130276637958&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3795822279B15 Linksys SRW224P] POE switch

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

=== Body of camera for developers ===

Case A consist of a large window on the top and transparent plex panel for closing. Anybody can
easy modified this panel for any application.

Case B consist a large space with two bodies. Can use same as back pannel can use for backpanel plex too.

[[Image:Devbody-1.png|thumb|Body for developers kit A]]
[[Image:Devbody-2.png|thumb|Body for developers kit B]]

10349

2007-10-12T14:24:49Z

Dimon:

Russia page [[10349.Ru]]

[[Image:10349RevC.jpg|thumb|Elphel 10349RevC boaard]]
[[Image:IDE-HD-1.8p.jpg|thumb|1.8" IDE HD with zif connector]]
[[Image:10349RevCon10353.jpg|thumb|10349 RevC mounted on 10353]]
=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Connector pinouts ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

==== Power consumption in different configurations ====

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

<table border="1">
<tr><td>2400 milliwatts</td><td>just booted</td></tr>
<tr><td>3000 milliwatts</td><td>after setting image parameters</td></tr>
<tr><td>3700 milliwatts</td><td>streamer on</td></tr>
<tr><td>3300 milliwatts</td><td>streamer off</td></tr>
<tr><td>3800 milliwatts</td><td>streamer on and somebody playing the stream</td></tr>
<tr><td>5000 milliwatts</td><td>with streamer on and HD writing at full speed (dd)</td></tr>
<tr><td>5800 milliwatts</td><td>streamer on, HD and USB-flash writing at full speed</td></tr>
<tr><td>3300 milliwatts</td><td>back to streamer off</td></tr>
</table>

Tests was performed with [http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1130276637958&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3795822279B15 Linksys SRW224P] POE switch

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

=== Body of camera for developers ===

Case A

[[Image:Devbody-1.png|thumb|Body for developers kit A]]
[[Image:Devbody-2.png|thumb|Body for developers kit B]]

File:Devbody-2.png

2007-10-12T14:23:27Z

Dimon:

File:Devbody-1.png

2007-10-12T14:22:47Z

Dimon:

10349

2007-10-12T14:22:05Z

Dimon:

10349

2007-09-14T07:05:03Z

Dimon: /* Power consumption in different configurations */

Russia page [[10349.Ru]]

=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Socket description ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

==== Power consumption in different configurations ====

Here are some results on power consumption test made in different configurations with Elphel 353 camera, 5MPix sensor, 10349 board, 1,8" HD and USB staff...

<table border="1">
<tr><td>2400 milliwatts</td><td>just booted</td></tr>
<tr><td>3000 milliwatts</td><td>after setting image parameters</td></tr>
<tr><td>3700 milliwatts</td><td>streamer on</td></tr>
<tr><td>3300 milliwatts</td><td>streamer off</td></tr>
<tr><td>3800 milliwatts</td><td>streamer on and somebody playing the stream</td></tr>
<tr><td>5000 milliwatts</td><td>with streamer on and HD writing at fool speed (dd)</td></tr>
<tr><td>5800 milliwatts</td><td>streamer on, HD and USB-flash writing at full speed</td></tr>
<tr><td>3300 milliwatts</td><td>back to streamer off</td></tr>
</table>

Tests was performed with [http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1130276637958&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=3795822279B15 Linksys SRW224P] POE switch

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. These are big secrets of the companies :(

Images and videos examples

2007-09-14T07:03:38Z

Dimon: /* Endoscopy camera */

=Images=

==3MPix micron sensor==
=== Examples of picture take with various lens type ===
This section compare various lenses used with Elphel 333 Camera and 3MPix sensor.

- computar Lens

- Fujinon Lens ref DF6HA-1B 1:1 2/6mm ([http://www.bhphotovideo.com/c/product/404242-REG/Fujinon_DF6HA1B_DF6HA_1B_6_mm_f_1_2.html:tilte spec])
Picture : view of Strasbourg - France [http://community.elphel.com/pictures/jmfcontrib/333_fujinon_DF6HA-1B.jpg]
take with follow settings : /admin-bin/ccam.cgi?opt=\*cvhxy\&sens=4\&e=10000\&iq=100

- EOS Canon adapter with professional lens 17-40 UMS ([http://community.elphel.com/pictures/jmfcontrib/jmf_view_canon17-40.JPG photo])
Picture : view of Strasbourg France [http://community.elphel.com/pictures/jmfcontrib/17-40pos17equiv80.3bague.ferme.jpg]
Picture : second view (minimum aperture) [http://community.elphel.com/pictures/jmfcontrib/17-40pos28.2bagus.testlimit.diaph6mm.ferme.jpg]
Picture : near object and maximum zoom. There is 3 pictures, each with focus on different object
- picture focus on paper [http://community.elphel.com/pictures/jmfcontrib/333_canon_28_80to80near_focus_paper.jpg]
- picture focus on water [http://community.elphel.com/pictures/jmfcontrib/333_canon_28_80to80near_focus_water.jpg]
- picture focus on USBKey [http://community.elphel.com/pictures/jmfcontrib/333_canon_28_80to80near_focus_usbkey.jpg]
focus seting is very sensitive. distance between lens and objects 1 meter.

Movie of country with Adapter for Canon Lens , Elphel 333. 3MPix [http://community.elphel.com/videos/333_canon_28_80to28set.ogg]

This not a industrial adaptator but only a first good experience.
Quality of image may be better in we include manual iris to have more deap in picture.

==5MPix micron sensor==

=== Examples of Electronic Rolling Shutter Distortion ===

A picture what was made from Elphel's Motor Office moving at approximately 40 mph. [http://community.elphel.com/pictures/Elphel_RV_in_ERS_mirror.jpg]

As in 5MPix resolution we have 1/15 second delay from the top to the bottom of the image everything is distorted. Everything but our reflection :)

One more example of distortion inducted by ERS: [http://community.elphel.com/pictures/ERS_in_motion_1.jpg]

Some info on what is [http://wiki.elphel.com/index.php?title=Electronic_Rolling_Shutter ERS] and what we intend to do to [http://wiki.elphel.com/index.php?title=Design_Ideas#Electronic_Rolling_Shutter_Distortion_Compensation compensate] this artifact.

=== Nature & animals ===

Humming birds: [http://community.elphel.com/pictures/hummingbird_1.jpg] [http://community.elphel.com/pictures/hummingbird_2.jpg]

Somewhere in Idaho: [http://community.elphel.com/pictures/1187443443.jpg] [http://community.elphel.com/pictures/1187443979.jpg]

=== Other ===

The logo from Elphel's Motor Office mirrored in a window. [http://community.elphel.com/pictures/RV_mirror.jpg]

==11MPix kodak sensor==

Just images, nothing special [http://community.elphel.com/pictures/363_1187266431.jpg], [http://community.elphel.com/pictures/363_1187266458.jpg], [http://community.elphel.com/pictures/363_1187266476.jpg]

Car license plate in the dark with headlights: [http://community.elphel.com/pictures/headlights_30ms_f8_g50_vsub2300.jpeg]

==Gated Intensified==

This picture was made by Elphel 303 camera model. This camera is no more produced but we plan to do another Gated intensified camera based on Elphel 353.
More info on [http://www.linuxdevices.com/articles/AT2171151224.html Linux devices].

303 photo made by another gated intensified 303: [http://community.elphel.com/pictures/303.jpg]

=Videos=
==HD cinema==
An HD cinema by Oscar Spierenburg [http://community.elphel.com/videos/RomainFULL.avi]

More about that [[HD_cinema_camera_Development_FAQ| here]]

First example done with Elphel 353 camera, 1600x1200 at 23 FPS (can be better): [http://community.elphel.com/videos/1600x1200_23FPS_quality_30.ogg]

An example of a 1920x1072 video at 24 FPS done with Elphel 353: [http://community.elphel.com/videos/1920x1072_24FPS.ogg]

==High FPS==
Slow motion fire show. This is a 512x384 resolution, 138 fps video done with an Elphel 333 camera with a 3 MPix sensor with out IR-cut filter. Exposure time was 4ms: [http://community.elphel.com/videos/Joel_138_fps.ogg]

===Sport application===

====100 FPS with timestamps watermarked====

Swimming: [http://community.elphel.com/videos/sport_100fps.ogg] and the "uncompressed" MJPEG version [http://community.elphel.com/videos/sport_100fps.avi]

====Photo finish====

Some info about [http://www.elphel.com/3fhlo/samples/pf/ photo finish]

==High res time lapse video==

Time laps videos by [http://redics.ch/ Redics.ch]

- Zolliken: [http://community.elphel.com/videos/zollikon.avi]

A time lapse video from Yellowstone: [http://community.elphel.com/videos/yellowstone.avi]

==Artistic==

Dancing filmed at 1280x960: [http://community.elphel.com/videos/dance-3.ogg]

Slow motion... filmed at 100 FPS replay at 24: [http://community.elphel.com/videos/Soazig_balle_100fps_replay_24fps.ogg]

Fire show 1024x768 at 44 FPS, 10ms exposure time: [http://community.elphel.com/videos/GOA_feux_1024x768_44fps_THEORA.ogg]

==Theora videos encoded by FPGA on Elphel 333==

Here some examples of Theora video encoded by the experimental Theora FPGA bistream and GNU/Linux softwares.

1024x768 @ 25 FPS, 70% quality (6.7M): [http://community.elphel.com/videos/stvs3_iq70.ogg], [http://community.elphel.com/videos/stvs2_iq70.ogg]

1024x768 @ 25 FPS, 60% quality (3.8M): [http://community.elphel.com/videos/stvs0_iq60.ogg], [http://community.elphel.com/videos/stvs1_iq60.ogg]

==Other==

Swiss watch mechanics 1024x768 @ 42 FPS: [http://community.elphel.com/videos/42.3_1024x768.ogg]

Rear view mirror of Elphel's Motor Office (1024x768 @ 24 FPS) : [http://community.elphel.com/videos/yellowstone_geisers_near_the_route.ogg], [http://community.elphel.com/videos/20070818-084649-20070818-085424-10877.ogg]

==Nature & animals==

Humming bird, 800x600 @ 21 FPS: [http://community.elphel.com/videos/hummingbird_1.ogg]

Humming birds, 2048x1536 @ 9 FPS: [http://community.elphel.com/videos/hummingbird_2.ogg]

=Medical=

==Endoscopy camera==

Those videos was made by a prototype of endoscopy camera based on Elphel 333. The test was performed in complete darkness with a halogen lamp of 80 Watt. In the black and white video you can see the resolution and in the color one the colors trough the endoscope.

At what moment the auto exposure in Elphel 333 was not stable enough to stabilize quickly and was not usable on humans for a real operation. We will soon make same tests with a Elphel 353 camera model.

1024x768 25fps endoscopy videos:

monochrome [48MB] - [http://www.elphel.com/video/test3.avi]

color [29MB] - [http://www.elphel.com/video/color1.avi]

This is our experimental cover for endoscopy camera:

[[Image:Cover-1.jpg]]

[[Image:Endocover-2.jpg]]

[[Image:Endocover-3.jpg]]

Endoscopy equipment:

Laparascope:
[[Image:Laparascope.jpg]]

Lighter:
[[Image:Endo-light1.jpg]]
[[Image:Endo-light2.jpg]]

File:Endo-light2.jpg

2007-09-14T06:59:13Z

Dimon:

File:Endo-light1.jpg

2007-09-14T06:58:53Z

Dimon:

File:Laparascope.jpg

2007-09-14T06:58:33Z

Dimon:

File:Endocover-3.jpg

2007-09-14T06:57:38Z

Dimon:

File:Endocover-2.jpg

2007-09-14T06:56:30Z

Dimon:

File:Cover-1.jpg

2007-09-14T06:54:32Z

Dimon:

10349

2007-09-11T20:45:22Z

Dimon: /* Socket description */

Russia page [[10349.Ru]]

=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Socket description ===

internal USB2, USB3, USB4
1 - power
2 - D-
3 - D+
4 - GND

J7 is the serial port
1 - RX
2 - TX
3 - CTS
4 - RTS
5 - GND
6 - removed, used as key

J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

J5 for connect external boards
1 - EXT0 (FPGA IO signal)
2 - EXT1 (FPGA IO signal)
3 - EXT2 (FPGA IO signal)
4 - EXT3 (FPGA IO signal)
5 - EXT4 (FPGA IO signal)
6 - GND
7 - EXT5 (FPGA IO signal)
8 - GND
9 - +3.3V
10 - +3.3V
11 - CTS (TTL level)
12 - RTS (TTL level)
13 - RX (TTL level)
14 - TX (TTL level)
15 - not connected
16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. It`s a big secret of a company :(

10349

2007-09-11T20:44:18Z

Dimon: add description of socket

Russia page [[10349.Ru]]

=== Interface board. ===

* serial port
* 4 ports USB hub with 3 internal, 1 external USB ports
* IDE port for the 1.8" hard drive with ZIF Flat cable
* 2 socket for external usermade board
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.

=== Socket description ===

* internal USB2, USB3, USB4
* 1 - power
* 2 - D-
* 3 - D+
* 4 - GND

* J7 is the serial port
* 1 - RX
* 2 - TX
* 3 - CTS
* 4 - RTS
* 5 - GND
* 6 - removed, used as key

* J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.

* J5 for connect external boards
* 1 - EXT0 (FPGA IO signal)
* 2 - EXT1 (FPGA IO signal)
* 3 - EXT2 (FPGA IO signal)
* 4 - EXT3 (FPGA IO signal)
* 5 - EXT4 (FPGA IO signal)
* 6 - GND
* 7 - EXT5 (FPGA IO signal)
* 8 - GND
* 9 - +3.3V
* 10 - +3.3V
* 11 - CTS (TTL level)
* 12 - RTS (TTL level)
* 13 - RX (TTL level)
* 14 - TX (TTL level)
* 15 - not connected
* 16 - not connected

=== Power description ===

It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.

=== Kit for Developers ===

* for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
* for internal USB sockets - AE10179-ND (Digi-Key) - 1
* for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
* or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
* blank PCB board V1255-ND (Digi-Key) - 1

=== Next revision ===

In new revision of this board we want use much more IDE interfaces.

* IDE port for a 2.5" hard drive
* IDE port for CompactFlash card
* IDE port a 1.8" hard drive with ZIF Flat cable
* SATA port

For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.

IDE-SATA bridges:

* JMicron [[http://www.jmicron.com.tw/JM20330.html JM20330]] (send email, no answer)
* Marvell [[http://www.marvell.com/products/storage/sata/index.jsp 88i8030, 88SA8040]] (need sign NDA, sucks)
* Silicon Image [[http://www.siliconimage.com/products/product.aspx?id=30 SiI3611]] (Available only through your local sales contact. send email, no answer)
* Atmel [[http://www.atmel.com/dyn/products/product_card.asp?family_id=677&family_name=Data+Storage&part_id=3456 AT78C5010]] (Available only through your local sales contact. send email, no answer)
* ACARD [[http://www.acard.com/english/fb01-product.jsp?prod_no=ARC-770&type1_title=Storage%20IC&type1_idno=1&idno_no=60 ARC-770]] (Available only through your local sales contact. send email, no answer)

Now I can`t found any datasheets for this. It`s a big secret of a company :(

Images and videos examples

2007-09-03T23:23:47Z

Dimon: /* Medical */

=Images=

==3MPix micron sensor==
=== Examples of various lens ===
This part compare various lens with sensor 3Mpix and 333 Elphel Camera.

- computar Lens

- Fujinon Lens

- Canon EOS Lens with adaptator [http://wiki.elphel.com/images/2/24/Jmf_canon_adap1.JPG] [http://wiki.elphel.com/images/e/ec/Jmf_canon_adapt2.JPG]

=== How to build a Canon EOS Lens adatator for Elphel 333===

A heasy way to build a C adaptator for Canon EOS Lens [http://wiki.elphel.com/images/f/ff/Jmf_333_with_canon_std.JPG].

Take a protection of lens, make a central holl and fixe two C/CS adaptators [http://wiki.elphel.com/images/f/f4/Jmf_cs_c.JPG]
to avec a good focal distance.

We have tested various Canon Lens that professional reporter lend me. [http://wiki.elphel.com/images/a/a4/Jmf_prof_lens.JPG]

- Canon Lens mounted on 333 : [http://wiki.elphel.com/images/7/7a/IMG_5526.JPG] [http://wiki.elphel.com/images/9/9f/Jmf_view_canon17-40.JPG]

''Pictures result of various lens :''

The main of this test is to try to use Canon EOS lens, more reference and less expensive of C Lens.
The second gool is to be able to use hight definition of CMOS sensor without optical resolution of C-Lens.
canon Eos UMS PRO 17-40 : mount of 333 Elphel [http://wiki.elphel.com/images/9/9f/Jmf_view_canon17-40.JPG]

-- view of Strasbourg House (France) [http://wiki.elphel.com/images/8/8d/17-40pos17equiv80.3bague.ferme.jpg]

-- second view with another set of Canon Lens (minimum apperture) [http://wiki.elphel.com/images/a/ac/17-40pos28.2bagus.testlimit.diaph6mm.ferme.jpg]

-- view of cat and barbie dole [http://wiki.elphel.com/images/3/31/Objectif50.2bagues.2chat.jpg]

In fact : a canon large vision become a Power Zoom this CMOS size difference. 35mm to 1/2" [http://wiki.elphel.com/images/7/71/Jmf_mount_canon_333.JPG]

Conclusion :
image quality is better than C-lens (varifocal computar our fixe-focal Fujinon)
but Canon lens become a super Zoom Lens and we not certify thermal stability of adjustment action (focus)

It will be fine to test a fishEyes for Canon.

Expensive projet of Adaptator to use EOS Lens can be find on net [http://www.mir.com.my/rb/photography/hardwares/classics/eos/EF-lenses/index.htm]
or [http://www.birger.com/Merchant2/merchant.mvc?Screen=ef232_home]

==5MPix micron sensor==

=== Examples of Electronic Rolling Shutter Distortion ===

A picture what was made from Elphel's Motor Office moving at approximately 40 mph. [http://community.elphel.com/pictures/Elphel_RV_in_ERS_mirror.jpg]

As in 5MPix resolution we have 1/15 second delay from the top to the bottom of the image everything is distorted. Everything but our reflection :)

One more example of distortion inducted by ERS: [http://community.elphel.com/pictures/ERS_in_motion_1.jpg]

Some info on what is [http://wiki.elphel.com/index.php?title=Electronic_Rolling_Shutter ERS] and what we intend to do to [http://wiki.elphel.com/index.php?title=Design_Ideas#Electronic_Rolling_Shutter_Distortion_Compensation compensate] this artifact.

=== Nature & animals ===

Humming birds: [http://community.elphel.com/pictures/hummingbird_1.jpg] [http://community.elphel.com/pictures/hummingbird_2.jpg]

Somewhere in Idaho: [http://community.elphel.com/pictures/1187443443.jpg] [http://community.elphel.com/pictures/1187443979.jpg]

=== Other ===

The logo from Elphel's Motor Office mirrored in a window. [http://community.elphel.com/pictures/RV_mirror.jpg]

==11MPix kodak sensor==

Just images, nothing special [http://community.elphel.com/pictures/363_1187266431.jpg], [http://community.elphel.com/pictures/363_1187266458.jpg], [http://community.elphel.com/pictures/363_1187266476.jpg]

Car license plate in the dark with headlights: [http://community.elphel.com/pictures/headlights_30ms_f8_g50_vsub2300.jpeg]

==Gated Intensified==

This picture was made by Elphel 303 camera model. This camera is no more produced but we plan to do another Gated intensified camera based on Elphel 353.
More info on [http://www.linuxdevices.com/articles/AT2171151224.html Linux devices].

303 photo made by another gated intensified 303: [http://community.elphel.com/pictures/303.jpg]

=Videos=
==HD cinema==
An HD cinema by Oscar Spierenburg [http://community.elphel.com/videos/RomainFULL.avi]

More about that [[HD_cinema_camera_Development_FAQ| here]]

==High FPS==
Slow motion fire show. This is a 512x384 resolution, 138 fps video done with an Elphel 333 camera with a 3 MPix sensor with out IR-cut filter. Exposure time was 4ms: [http://community.elphel.com/videos/Joel_138_fps.ogg]

===Sport application===

====100 FPS with timestamps watermarked====

Swimming: [http://community.elphel.com/videos/sport_100fps.ogg] and the "uncompressed" MJPEG version [http://community.elphel.com/videos/sport_100fps.avi]

====Photo finish====

Some info about [http://www.elphel.com/3fhlo/samples/pf/ photo finish]

==High res time lapse video==

A time lapse video from Yellowstone: [http://community.elphel.com/videos/yellowstone.avi]

==Artistic==

Dancing filmed at 1280x960: [http://community.elphel.com/videos/dance-3.ogg]

Slow motion... filmed at 100fps replay at 24: [http://community.elphel.com/videos/Soazig_balle_100fps_replay_24fps.ogg]

==Theora videos encoded by FPGA on Elphel 333==

Here some examples of Theora video encoded by the experimental Theora FPGA bistream and GNU/Linux softwares.

1024x768 @ 25 FPS, 70% quality (6.7M): [http://community.elphel.com/videos/stvs3_iq70.ogg], [http://community.elphel.com/videos/stvs2_iq70.ogg]

1024x768 @ 25 FPS, 60% quality (3.8M): [http://community.elphel.com/videos/stvs0_iq60.ogg], [http://community.elphel.com/videos/stvs1_iq60.ogg]

==Other==

Swiss watch mechanics 1024x768 @ 42 FPS: [http://community.elphel.com/videos/42.3_1024x768.ogg]

Rear view mirror of Elphel's Motor Office (1024x768 @ 24 FPS) : [http://community.elphel.com/videos/yellowstone_geisers_near_the_route.ogg], [http://community.elphel.com/videos/20070818-084649-20070818-085424-10877.ogg]

==Nature & animals==

Humming bird, 800x600 @ 21 FPS: [http://community.elphel.com/videos/hummingbird_1.ogg]

Humming birds, 2048x1536 @ 9 FPS: [http://community.elphel.com/videos/hummingbird_2.ogg]

=Medical=

Some videos from medical endoscopy camera, 1024x768 25fps

monochrome [48MB] - [http://www.elphel.com/video/test3.avi download]
color [29MB] - [http://www.elphel.com/video/color1.avi download]

Talk:Synchronous lighting

2007-08-05T21:13:17Z

Dimon:

Do you know [http://en.wikipedia.org/wiki/DMX512-A DMX protocol]? it can be used to control diodes.

One of our clients/partners will certainly port DMX protocol in to FPGA.

10349

2007-08-02T20:46:08Z

Dimon: /* Next revision */

10349

2007-08-02T20:45:20Z

Dimon: /* Next revision */

10349

2007-08-02T20:44:33Z

Dimon: add link to menefacturer

10349

2007-08-02T20:40:24Z

Dimon: Add new bridge ARC-770

10349

2007-08-01T01:43:51Z

Dimon: /* Next revision */

10349

2007-08-01T01:26:28Z

Dimon: /* Next revision */

10349

2007-08-01T01:06:49Z

Dimon: /* Next revision */

10349

2007-07-31T22:11:07Z

Dimon: /* Next revision */

10349

2007-07-31T21:57:10Z

Dimon:

Alternative IO board for 10353/10363 series

2007-07-26T02:11:52Z

Dimon:

Description and duscussion about new IO board for 10353/10363 series

* USB ports, 1 external, 2 internal small non-standart connector pinhead 2mm pitch
* serial port, pinhead connector 2mm pitch
* IDE port for 1.8" hard drives with Flat Flex cable.
* GPIO opto-isolated or via buffer, pinhead 2mm pitch
* USB sound card on board with in-out
* socket for GPS module. GPS module and serial port can not work together
* 3-axises accelerometers

Comments??

Dima, you should clearly mark is as a proposal for discussion.I would rather see (compact) lens control circuitry (both variants - 2-wire and EOS-compatible). Other people would suggest aaudio as a standard feature--[[User:Andrey.filippov|Andrey.filippov]] 09:56, 16 July 2007 (CDT)

For 2-wire need 12V power supply.
Power requrements:
* 5V for USB 0.3A per port (max load)
* 12V 0.3A for 2-wire lens control board 10331
--[[User:Dimon|dimon]] 18:41, 16 July 2007 (CDT)

Connectors 2mm pitch:
* 2 USB internal ports - 8 pin
* RS-232 port - 4 pin
* 10331+EOS port - 10 pin
* 4 input, 4 output - 8 pin
* audio in 3, audio out 3 - 6pin

I make 3D model of this board(Varicad). See here:
[http://www.oshec.org/Members/dimon/rabota/new_IO.dwb 3D model]

--[[User:Dimon|dimon]] 02:18, 25 July 2007 (CDT)

New 3D model of board uploaded. This is model with GPS module and audio connector. See here:
[http://www.oshec.org/Members/dimon/rabota/new_IO_GPS.dwb 3D model + GPS]

What about board? Can I start make design? Or need discuss more?

--[[User:Dimon|dimon]] 21:11, 25 July 2007 (CDT)