10359 test - Revision history

Oleg at 02:15, 7 December 2009

2009-12-07T02:15:35Z

← Older revision		Revision as of 02:15, 7 December 2009
Line 1:		Line 1:
	===Test Plan===		===Test Plan===
	----		----
	0. Update CVS ~~from elphel-community~~
			0. Update CVS, for testing the 10359 board the php script '''<font size="3">test_inner_10359.php</font>''' is ised.

	1. "Detect 10359"		1. "Detect 10359"

Oleg at 09:06, 5 October 2009

2009-10-05T09:06:09Z

← Older revision		Revision as of 09:06, 5 October 2009
Line 4:		Line 4:

	1. "Detect 10359"		1. "Detect 10359"
	a. ~~Go to 2. - it will give the board ID.~~
	OR		a. Based on Andrey's bdetect.php
	b. Andrey's ~~method (but reboot or reconfiguration is needed because I2C bus uses the same wires as JTAG and won't work after getting board ID)~~		Do : check for the file '/var/log/bdetect' created by bdetect.php - it contains information about extra boards
	Do : bdetect.php ~~/Can be only done until the 10359 board FPGA is programmed /~~
	Response : board ID.		Response : board ID.
	Error(fatal) : "Failed to detect 10359".		Error(fatal) : "Failed to detect 10359".

Oleg at 11:17, 9 October 2008

2008-10-09T11:17:40Z

← Older revision		Revision as of 11:17, 9 October 2008
Line 23:		Line 23:
	Error(fatal) : "Sensor is not detected or I2C bus between 10359 and 10338 on channel 0 doesn't work".		Error(fatal) : "Sensor is not detected or I2C bus between 10359 and 10338 on channel 0 doesn't work".

	4. (~~Not test~~) "Program channels 1 and 2"		4. (needed configuration) "Program channels 1 and 2"
	Do : camera_demo_359.php		Do : camera_demo_359.php
	Comment : frequency 96MHz is set and all sensors are programmed. Even if some of sensors do not present - i2c commands are sent		Comment : frequency 96MHz is set and all sensors are programmed. Even if some of sensors do not present - i2c commands are sent

Oleg at 12:16, 8 October 2008

2008-10-08T12:16:52Z

← Older revision		Revision as of 12:16, 8 October 2008
Line 1:		Line 1:
	===Test Plan===		===Test Plan===
	----		----
			0. Update CVS from elphel-community

	1. "Detect 10359"		1. "Detect 10359"
	а. Andrey's method		a. Go to 2. - it will give the board ID.
			OR
			b. Andrey's method (but reboot or reconfiguration is needed because I2C bus uses the same wires as JTAG and won't work after getting board ID)
	Do : bdetect.php /Can be only done until the 10359 board FPGA is programmed /		Do : bdetect.php /Can be only done until the 10359 board FPGA is programmed /
	Response : board ID.		Response : board ID.

Andrey.filippov at 17:48, 7 October 2008

2008-10-07T17:48:10Z

← Older revision		Revision as of 17:48, 7 October 2008
Line 3:		Line 3:
	1. "Detect 10359"		1. "Detect 10359"
	а. Andrey's method		а. Andrey's method
	Do : bdetect.php /Can be only done until the 10359 board FPGA is programmed ~~--[[User:Andrey.filippov\|Andrey.filippov]] 12:47, 7 October 2008 (CDT)~~/		Do : bdetect.php /Can be only done until the 10359 board FPGA is programmed /
	Response : board ID.		Response : board ID.
	Error(fatal) : "Failed to detect 10359".		Error(fatal) : "Failed to detect 10359".

Andrey.filippov at 17:47, 7 October 2008

2008-10-07T17:47:39Z

← Older revision		Revision as of 17:47, 7 October 2008
Line 3:		Line 3:
	1. "Detect 10359"		1. "Detect 10359"
	а. Andrey's method		а. Andrey's method
	Do : bdetect.php		Do : bdetect.php /Can be only done until the 10359 board FPGA is programmed --[[User:Andrey.filippov\|Andrey.filippov]] 12:47, 7 October 2008 (CDT)/
	Response : board ID.		Response : board ID.
	Error(fatal) : "Failed to detect 10359".		Error(fatal) : "Failed to detect 10359".

Oleg at 16:09, 7 October 2008

2008-10-07T16:09:41Z

← Older revision		Revision as of 16:09, 7 October 2008
Line 3:		Line 3:
	1. "Detect 10359"		1. "Detect 10359"
	а. Andrey's method		а. Andrey's method
	Do : ~~?????~~		Do : bdetect.php
	Response : board ID.		Response : board ID.
	Error(fatal) : "Failed to detect 10359".		Error(fatal) : "Failed to detect 10359".

Oleg at 21:16, 6 October 2008

2008-10-06T21:16:55Z

← Older revision		Revision as of 21:16, 6 October 2008
Line 1:		Line 1:
	===Test Plan===		===Test Plan===
			----
	1. "Detect 10359"		1. "Detect 10359"
	а. Andrey's method		а. Andrey's method

Oleg at 21:16, 6 October 2008

2008-10-06T21:16:33Z

← Older revision		Revision as of 21:16, 6 October 2008
Line 1:		Line 1:
	Test Plan:		===Test Plan===

	1. "Detect 10359"		1. "Detect 10359"
Line 23:		Line 23:
	Comment : frequency 96MHz is set and all sensors are programmed. Even if some of sensors do not present - i2c commands are sent		Comment : frequency 96MHz is set and all sensors are programmed. Even if some of sensors do not present - i2c commands are sent

	4. "Detect sensors on channel 1 and 2"		5. "Detect sensors on channel 1 and 2"
	а. Switch to a channel and read sensor's ID through I2C bus.		а. Switch to a channel and read sensor's ID through I2C bus.
	Do : ch1 - "i2c_send(16,0,0x835,0x2,0);i2c_receive(16,0,0x4800,0);"		Do : ch1 - "i2c_send(16,0,0x835,0x2,0);i2c_receive(16,0,0x4800,0);"
Line 30:		Line 30:
	Error : if any of the IDs is wrong - "sensor X is not detected or I2C bus between 10359 and 10338 on channel X doesn't work".		Error : if any of the IDs is wrong - "sensor X is not detected or I2C bus between 10359 and 10338 on channel X doesn't work".

	5. Adjust phases for detected channels.		6. Adjust phases for detected channels.
	a. For each channel in the test pattern mode apply phase steps until correct MD5 is calculated twice. Fixed number of steps.		a. For each channel in the test pattern mode apply phase steps until correct MD5 is calculated twice. Fixed number of steps.
	Do : switch channel - "i2c_send(16,0,0x835,0x2,0);"		Do : switch channel - "i2c_send(16,0,0x835,0x2,0);"
Line 41:		Line 41:

	---------------------------------------------------------------------------------------------------------		---------------------------------------------------------------------------------------------------------
	-- Correct MD5s automatically means that data buses are ok		Correct MD5s automatically means that data buses are ok
	---------------------------------------------------------------------------------------------------------		---------------------------------------------------------------------------------------------------------

	6. "SDRAM check"		7. "SDRAM check"
	a. Read/write a couple of pages to SDRAM.		a. Read/write a couple of pages to SDRAM.
	Do : mem_test.php		Do : mem_test.php
	Error: "SDRAM test failed". (SDRAM phase depends on DCM1(channel 0))		Error: "SDRAM test failed". (SDRAM phase depends on DCM1(channel 0))

Oleg at 21:10, 6 October 2008

2008-10-06T21:10:54Z

New page

Test Plan:

1. "Detect 10359"
а. Andrey's method
Do : ?????
Response : board ID.
Error(fatal) : "Failed to detect 10359".

2. "10353-10359 I2C connection check"
а. Read read board revision through i2c:
Do : "i2c_receive(16,0,0x800,0);"
Response : 0x0359.
Error(fatal) : "I2C bus doesn't work".

3. "Detect sensor on channel 0" (after configuration channel 0 is set by default).
а. Read sensor ID through I2C
Do : "i2c_receive(16,0,0x4800,0);"
Response : 0x1801 (5MPix sensor).
Error(fatal) : "Sensor is not detected or I2C bus between 10359 and 10338 on channel 0 doesn't work".

4. (Not test) "Program channels 1 and 2"
Do : camera_demo_359.php
Comment : frequency 96MHz is set and all sensors are programmed. Even if some of sensors do not present - i2c commands are sent

4. "Detect sensors on channel 1 and 2"
а. Switch to a channel and read sensor's ID through I2C bus.
Do : ch1 - "i2c_send(16,0,0x835,0x2,0);i2c_receive(16,0,0x4800,0);"
ch2 - "i2c_send(16,0,0x835,0x4,0);i2c_receive(16,0,0x4800,0);"
Response : 0x1801 from each (5MPix) sensor.
Error : if any of the IDs is wrong - "sensor X is not detected or I2C bus between 10359 and 10338 on channel X doesn't work".

5. Adjust phases for detected channels.
a. For each channel in the test pattern mode apply phase steps until correct MD5 is calculated twice. Fixed number of steps.
Do : switch channel - "i2c_send(16,0,0x835,0x2,0);"
test pattern mode - "exec("fpcf -i2cw16 48a0 0041");"
phases_adjust.php?dcm=1&shift_phase=1&N=5&sphase=7
Error : "Failed to adjust phase for channel Х".
a) Failed for channel 0: bus "359-ch0" doesn't work good.
б) Failed for channel 1 and 2, but for channel 0 is ok: bus "359-chX" doesn't work good.
в) Failed for all channel: "bus 353-359 or all the other buses" don't work properly.

---------------------------------------------------------------------------------------------------------
-- Correct MD5s automatically means that data buses are ok
---------------------------------------------------------------------------------------------------------

6. "SDRAM check"
a. Read/write a couple of pages to SDRAM.
Do : mem_test.php
Error: "SDRAM test failed". (SDRAM phase depends on DCM1(channel 0))