10369 - Revision history

Oleg at 21:46, 20 January 2015

2015-01-20T21:46:56Z

← Older revision		Revision as of 21:46, 20 January 2015
Line 704:		Line 704:
	\|}		\|}
	'' '''Note:''' To make a simple temperature sensor for this circuit, a small NPN or PNP transistor can be used. It is best to use a shielded, twisted pair cable to connect the external sensor to the terminals on the 10369 board. Start by soldering the shield wire to GND on W4. Then solder together the base and the collector of the sensor transistor. If using an NPN transistor (i.e. 2N3904), solder one wire from the transistor's base to W2, and the other wire from the emitter to W3. If using a PNP transistor (i.e. 2N3906), solder one wire from the transistor's emitter to W2, and the other wire from the base to W3. If no external sensor is used, but a temperature controlled cooling fan is needed, W2 and W3 should be connected together. This will allow the 10369 board's built in fan control to set the fan speed based on the board's internal temperature sensor.''		'' '''Note:''' To make a simple temperature sensor for this circuit, a small NPN or PNP transistor can be used. It is best to use a shielded, twisted pair cable to connect the external sensor to the terminals on the 10369 board. Start by soldering the shield wire to GND on W4. Then solder together the base and the collector of the sensor transistor. If using an NPN transistor (i.e. 2N3904), solder one wire from the transistor's base to W2, and the other wire from the emitter to W3. If using a PNP transistor (i.e. 2N3906), solder one wire from the transistor's emitter to W2, and the other wire from the base to W3. If no external sensor is used, but a temperature controlled cooling fan is needed, W2 and W3 should be connected together. This will allow the 10369 board's built in fan control to set the fan speed based on the board's internal temperature sensor.''


			=== Fix a potential problem with SATA bridge proper reset===
			* remove C9 (Fig. A)
			* remove R9 (Fig. B)
			* connect pins 16 and 17 of U8 (Fig. B)
			{\|
			\|[[File:10369 sata reset fix A.JPG\|thumb\|400px\|Fig.A Bottom View]]
			\|[[File:10369 sata reset fix B.JPG\|thumb\|400px\|Fig.B Top View]]
			\|}

Oleg: /* J15 - SYNC (external) */

2011-11-18T20:01:12Z

J15 - SYNC (external)

← Older revision		Revision as of 20:01, 18 November 2011
Line 642:		Line 642:
	'' '''Note:''' In order to synchronize multiple cameras connect the pins 2 on all cameras together, same for all the pins 3. Additionally connect pin 1 on the 'master' (synchronization source) camera to pin 3, pin 4 - with pin2.''		'' '''Note:''' In order to synchronize multiple cameras connect the pins 2 on all cameras together, same for all the pins 3. Additionally connect pin 1 on the 'master' (synchronization source) camera to pin 3, pin 4 - with pin2.''
	{\|		{\|
	\|[[File:Sync cable.png\|400px\|thumb\|Fig. Synchronize 2 cameras with one used as a source]]		\|[[File:Sync cable.png\|400px\|thumb\|Fig. Synchronize 3 cameras with one used as a source]]
	\|}		\|}
	----		----

Oleg: /* J15 - SYNC (external) */

2011-11-18T19:49:45Z

J15 - SYNC (external)

← Older revision		Revision as of 19:49, 18 November 2011
Line 627:		Line 627:
	==== J15 - SYNC (external) ====		==== J15 - SYNC (external) ====
	{\| class="wikitable" style="background:#fcfcfc; " border="1"		{\| class="wikitable" style="background:#fcfcfc; " border="1"
	\|+ Intercamera synchronization I/O, modular RJ-11		\|+ Intercamera synchronization I/O, modular RJ-11 (type 4P4C)
	\|-		\|-
	! Pin !! Signal !! Notes		! Pin !! Signal !! Notes

Oleg: /* J15 - SYNC (external) */

2011-11-09T19:04:23Z

J15 - SYNC (external)

← Older revision		Revision as of 19:04, 9 November 2011
Line 641:		Line 641:
	\|}		\|}
	'' '''Note:''' In order to synchronize multiple cameras connect the pins 2 on all cameras together, same for all the pins 3. Additionally connect pin 1 on the 'master' (synchronization source) camera to pin 3, pin 4 - with pin2.''		'' '''Note:''' In order to synchronize multiple cameras connect the pins 2 on all cameras together, same for all the pins 3. Additionally connect pin 1 on the 'master' (synchronization source) camera to pin 3, pin 4 - with pin2.''
			{\|
			\|[[File:Sync cable.png\|400px\|thumb\|Fig. Synchronize 2 cameras with one used as a source]]
			\|}
	----		----

Andrey.filippov: /* Adapters */

2011-07-08T23:28:13Z

Adapters

← Older revision		Revision as of 23:28, 8 July 2011
Line 27:		Line 27:
	*[[103692]] - adapter for the ZIF-type (flex cable connector) 1.8" HDD		*[[103692]] - adapter for the ZIF-type (flex cable connector) 1.8" HDD
	*[[103693]] - USB type A (host) connector adapter mounted on the back panel of the [[353 \| Elphel Model 353 camera]].		*[[103693]] - USB type A (host) connector adapter mounted on the back panel of the [[353 \| Elphel Model 353 camera]].
			*[[103695]] - IMU adapter board.
			*[[103696]] - Serial GPS with synchronization signal adapter board.
	*[[RJ45/DB9F_Modular_Adapter]] - DB9F to RJ45/RJ25 modular adapter		*[[RJ45/DB9F_Modular_Adapter]] - DB9F to RJ45/RJ25 modular adapter

Oleg: /* J15 - SYNC (external) */

2011-04-22T19:43:37Z

J15 - SYNC (external)

← Older revision		Revision as of 19:43, 22 April 2011
Line 625:		Line 625:
	==== J15 - SYNC (external) ====		==== J15 - SYNC (external) ====
	{\| class="wikitable" style="background:#fcfcfc; " border="1"		{\| class="wikitable" style="background:#fcfcfc; " border="1"
	\|+ Intercamera synchronization I/O, modular RJ-14		\|+ Intercamera synchronization I/O, modular RJ-11
	\|-		\|-
	! Pin !! Signal !! Notes		! Pin !! Signal !! Notes

Olga: /* J17 - Fan */

2010-06-02T18:14:48Z

J17 - Fan

← Older revision		Revision as of 18:14, 2 June 2010
Line 674:		Line 674:
	! Pin !! Signal !! Notes		! Pin !! Signal !! Notes
	\|-		\|-
	\| 1 \|\| FANPOS \|\| Fan positive terminal		\| 1 \|\| FANPOS \|\| Fan positive terminal '''<font color=red>(Red)</font>'''
	\|-		\|-
	\| 2 \|\| GND \|\| Fan negative terminal		\| 2 \|\| GND \|\| Fan negative terminal '''(Black)'''
	\|-		\|-
	\|}		\|}

Oleg at 21:41, 11 January 2010

2010-01-11T21:41:14Z

← Older revision		Revision as of 21:41, 11 January 2010
Line 31:		Line 31:
	=== Notes ===		=== Notes ===
	<font color=red>		<font color=red>
	* It can be impossible to mount an external SATA disk to the camera with an internal 18"HDD (NC353L-369A-HDD) as the internal disk does not react on master/slave-option bus and also it doesn't tristate the signals it shares with the SATA bridge.		* It can be impossible to mount an external SATA disk to the camera with an internal 18"HDD (NC353L-369A-HDD) as the internal disk (Toshiba MK1214GAH) does not react on master/slave-option bus and also it doesn't tristate the signals it shares with the SATA bridge.
	</font>		</font>

Oleg at 21:36, 11 January 2010

2010-01-11T21:36:49Z

← Older revision		Revision as of 21:36, 11 January 2010
Line 28:		Line 28:
	*[[103693]] - USB type A (host) connector adapter mounted on the back panel of the [[353 \| Elphel Model 353 camera]].		*[[103693]] - USB type A (host) connector adapter mounted on the back panel of the [[353 \| Elphel Model 353 camera]].
	*[[RJ45/DB9F_Modular_Adapter]] - DB9F to RJ45/RJ25 modular adapter		*[[RJ45/DB9F_Modular_Adapter]] - DB9F to RJ45/RJ25 modular adapter

			=== Notes ===
			<font color=red>
			* It can be impossible to mount an external SATA disk to the camera with an internal 18"HDD (NC353L-369A-HDD) as the internal disk does not react on master/slave-option bus and also it doesn't tristate the signals it shares with the SATA bridge.
			</font>


	<br clear="all" />		<br clear="all" />

Polto: /* Example - reading status of CF cards installed): */

2009-08-17T07:46:47Z

Example - reading status of CF cards installed):

← Older revision		Revision as of 07:46, 17 August 2009
Line 72:		Line 72:
	======Example - reading status of CF cards installed):======		======Example - reading status of CF cards installed):======

	http://192.168.0.73/i2c.php?bus=1&raw=0x2000		http://192.168.0.9/i2c.php?bus=1&raw=0x2000

	result (CF0 present, CF1 - not installed, outputs - default):		result (CF0 present, CF1 - not installed, outputs - default):