Elphel cameras and Zoneminder - Revision history

Cordel: /* Using ImgSrv to configure your monitor */

2008-09-26T20:13:58Z

Using ImgSrv to configure your monitor

← Older revision		Revision as of 20:13, 26 September 2008
Line 23:		Line 23:

	== Using ImgSrv to configure your monitor ==		== Using ImgSrv to configure your monitor ==
	To use [[imgsrv]] all you must do is set the port to 8081 and the path to either /bimg for for an image grab or to /mbimg to get a mjpeg push stream. There ~~are~~ to the best of my knowledge thus far, any way to request image parameters (Image size, scaling, etc.) or fps through the path so these must be set directly on the Elphel camera and your settings in ZM must match. You should also set on the camera to enable "Video Streamer" so that the camera continues to update its buffer.		To use [[imgsrv]] all you must do is set the port to 8081 and the path to either /bimg for for an image grab or to /mbimg to get a mjpeg push stream. There is to the best of my knowledge thus far, not any way to request image parameters (Image size, scaling, etc.) or fps through the path using [[imgsrv]] so these must be set directly on the Elphel camera and your settings in ZM must match. If the setting do not match, ZM will not acquire the image being sent.You should also set on the camera to enable "Video Streamer" so that the camera continues to update its buffer.

	[[Image:Elphel-config-streamer.jpg]]		[[Image:Elphel-config-streamer.jpg]]

2008-09-26T20:11:08Z

← Older revision		Revision as of 20:11, 26 September 2008
Line 23:		Line 23:

	== Using ImgSrv to configure your monitor ==		== Using ImgSrv to configure your monitor ==
	~~Currently working~~ to ~~implement~~.		To use [[imgsrv]] all you must do is set the port to 8081 and the path to either /bimg for for an image grab or to /mbimg to get a mjpeg push stream. There are to the best of my knowledge thus far, any way to request image parameters (Image size, scaling, etc.) or fps through the path so these must be set directly on the Elphel camera and your settings in ZM must match. You should also set on the camera to enable "Video Streamer" so that the camera continues to update its buffer.

			[[Image:Elphel-config-streamer.jpg]]

			[[Image:Elphel-config-size.jpg]]


			ZoneMinder Settings you do not want to set a limit on fps as this has to be regulated at the camera on the following mjpeg push configuration.
			[[Image:Config-source2.jpg]]

2008-09-25T01:45:34Z

← Older revision		Revision as of 01:45, 25 September 2008
Line 6:		Line 6:
	* the RTP/RTSP streamer can be used with [[MPlayer]] and [[AVLD_-_Another_Video_Loopback_Device \| AVLD]]		* the RTP/RTSP streamer can be used with [[MPlayer]] and [[AVLD_-_Another_Video_Loopback_Device \| AVLD]]
	* or the best way: RTP/RTSP integration in ZoneMinder		* or the best way: RTP/RTSP integration in ZoneMinder


			= Configuring Elphel cameras and ZoneMinder =

			== Using ccam.cgi to configure your monitor ==
			Using the ccam.cgi to grap a snapshot in ZoneMinder works well. You will be able to easily implement this.
			Keep in mind that ZoneMinder has no facilities to determine the image size so this must be manually set in ZoneMinder to match the image being sent by the camera. Alternatively you can set the image dimensions in the path in ZM which would be preferred just in case for some reason someone changes the dimensions on the camera it self which would make ZM unable to process the images. These are my findings after having a go of it for a half hour:
			Using [[Ccam.cgi]]. ccam.cgi will soon be depreciated in favor of [[imgsrv]].


			Using " /admin-bin/ccam.cgi?opt=vhcxy " as your path in ZoneMinders Monitor configuration ( Keep in mind that I am using the sandbox camera so I'm not going to bother benchmarking )

			[[Image:Config-general.jpg]]
			[[Image:Config-source1.jpg]]
			[[Image:Zm-Monitor1.jpg]]

			== Using ImgSrv to configure your monitor ==
			Currently working to implement.

2008-09-21T22:56:48Z

← Older revision		Revision as of 22:56, 21 September 2008
Line 1:		Line 1:
	We plan to make model 353 camera work with [http://www.zoneminder.com Zoneminder]		We plan to make model 353 camera work with [http://www.zoneminder.com Zoneminder]

			Several ways may be considered:

			* [[imgsrv]] have the possibility to send MJPEG stream over HTTP
			* the RTP/RTSP streamer can be used with [[MPlayer]] and [[AVLD_-_Another_Video_Loopback_Device \| AVLD]]
			* or the best way: RTP/RTSP integration in ZoneMinder

2008-09-21T22:47:13Z

← Older revision		Revision as of 22:47, 21 September 2008
Line 1:		Line 1:
	~~'''''Elphel Network Cameras Manual'''''~~		We plan to make model 353 camera work with [http://www.zoneminder.com Zoneminder]
	~~----~~
	~~[[Using the cameras]] \|~~
	~~[[Camera software]] \|~~
	~~[[Camera hardware]] \|~~
	~~[[Diagnostic and repair]] \|~~
	~~[[Development documentation]] \|~~
	~~[[Information]] \|~~
	~~[[Glossary]] \|~~
	~~[[About Elphel, Inc]]~~
	~~----~~
	~~[[Photo-finish]] \|~~
	~~[[Zeroconf for Elphel cameras]] \|~~
	~~[[Elphel cameras and Zoneminder]] \|~~
	~~[[USB host interface]] \|~~
	~~[[Motorized lens control]] \|~~
	~~[[Outdoor enclosure]]~~
	~~----~~

	~~===Write your texts here===~~
	We plan to make model ~~333~~ camera work with [http://www.zoneminder.com Zoneminder]
	~~----~~
	~~''Free Software and Open Hardware. Elphel, Inc., 2005''~~

2005-09-22T22:11:03Z

Write your texts here

← Older revision		Revision as of 22:11, 22 September 2005
Line 19:		Line 19:

	===Write your texts here===		===Write your texts here===
			We plan to make model 333 camera work with [http://www.zoneminder.com Zoneminder]
	----		----
	''Free Software and Open Hardware. Elphel, Inc., 2005''		''Free Software and Open Hardware. Elphel, Inc., 2005''

2005-09-22T22:06:38Z

New page