Network configuration - Revision history

Andrey.filippov at 23:13, 24 October 2018

2018-10-24T23:13:34Z

← Older revision		Revision as of 23:13, 24 October 2018
Line 1:		Line 1:
	{{Legacy}}		{{Legacy}}
			= NC393 cameras =
	Network configuration for the NC393 cameras is ~~here~~: [[10393_manual#Change_default_ip_address]]		Network configuration for the NC393 cameras is documented in 10393 Manual: [[10393_manual#Change_default_ip_address]]


			= Elphel 353 network config =
	Network camera and especially RTP/RTSP network streaming require a proper network configuration. Here is the list of default settings and some hacks you can do.		Network camera and especially RTP/RTSP network streaming require a proper network configuration. Here is the list of default settings and some hacks you can do.

	~~= Elphel 353 network config =~~

	== Serial Number/Ethernet Address ==		== Serial Number/Ethernet Address ==

Andrey.filippov at 23:11, 24 October 2018

2018-10-24T23:11:07Z

← Older revision		Revision as of 23:11, 24 October 2018
Line 1:		Line 1:
			{{Legacy}}

			Network configuration for the NC393 cameras is here: [[10393_manual#Change_default_ip_address]]


	Network camera and especially RTP/RTSP network streaming require a proper network configuration. Here is the list of default settings and some hacks you can do.		Network camera and especially RTP/RTSP network streaming require a proper network configuration. Here is the list of default settings and some hacks you can do.

Spectr: /* ipsetd */

2008-06-27T21:29:23Z

ipsetd

← Older revision		Revision as of 21:29, 27 June 2008
Line 54:		Line 54:
	Example:		Example:
	arp -s 123.45.67.89 00:40:8c:12:34:56		arp -s 123.45.67.89 00:40:8c:12:34:56
	ping -s 408*) 123.45.67.89		ping -s 408 123.45.67.89

	The unit responds to the ping in the examples above if the new address was configured. Note, this method(ARP/ping mehtod above) only sets the IP address temporarily (while the unit is powered). To make the change permanent the ip paramters (IP address, subnet mask and gateway address) must be set in a file on the camera, otherwise the default network settings will be restored again when the board is rebooted and you will have to start all over again.		The unit responds to the ping in the examples above if the new address was configured. Note, this method(ARP/ping mehtod above) only sets the IP address temporarily (while the unit is powered). To make the change permanent the ip paramters (IP address, subnet mask and gateway address) must be set in a file on the camera, otherwise the default network settings will be restored again when the board is rebooted and you will have to start all over again.

Visitor: /* Default config */

2008-05-09T06:21:24Z

Default config

← Older revision		Revision as of 06:21, 9 May 2008
Line 13:		Line 13:
	== Default config ==		== Default config ==
	By default the camera start with preconfigured IP address:		By default the camera start with preconfigured IP address:
	192.168.0.9 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.~~1668~~.0.15		192.168.0.9 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.15

	The default streamer configuration is to multicast on:		The default streamer configuration is to multicast on:

Polto: /* Your PC network configuration */

2008-05-07T22:59:56Z

Your PC network configuration

← Older revision		Revision as of 22:59, 7 May 2008
Line 60:		Line 60:
	= Your PC network configuration =		= Your PC network configuration =
	Your PC/Mac should be configured by default as:		Your PC/Mac should be configured by default as:
	192.168.0.15 netmask 255.255.255.0 ~~and~~ broadcast 192.168.0.255		192.168.0.15 netmask 255.255.255.0 broadcast 192.168.0.255

			''' Attention! Check your firewall! ''' Before spending hours trying to understand why multicast does not work check if your firewall do not block it.

	You need to add route to the multicast address. Both commands can be resumed like:		You need to add route to the multicast address. Both commands can be resumed like:

Polto: /* My wifi network is in 192.168.0.0/24 network */

2008-04-19T22:15:08Z

My wifi network is in 192.168.0.0/24 network

← Older revision		Revision as of 22:15, 19 April 2008
Line 74:		Line 74:

	sudo ifconfig eth1 192.168.0.15 netmask 255.255.255.248		sudo ifconfig eth1 192.168.0.15 netmask 255.255.255.248
	sudo route add -net 232.8.1.0 netmask 255.~~255~~.~~255~~.0 dev eth1		sudo route add -net 232.0.0.0 netmask 255.0.0.0 dev eth1

	So my routes are:		So my routes are:

Polto: /* Your PC network configuration */

2008-04-19T22:14:34Z

Your PC network configuration

← Older revision		Revision as of 22:14, 19 April 2008
Line 64:		Line 64:
	You need to add route to the multicast address. Both commands can be resumed like:		You need to add route to the multicast address. Both commands can be resumed like:
	sudo ifconfig eth1 192.168.0.15 netmask 255.255.255.0		sudo ifconfig eth1 192.168.0.15 netmask 255.255.255.0
	sudo route add -net 232.8.1.0 netmask 255.~~255~~.~~255~~.0 dev eth1		sudo route add -net 232.0.0.0 netmask 255.0.0.0 dev eth1
	This suppose what your camera is connected on eth1. (eth0 is my wifi)		This suppose what your camera is connected on eth1. (eth0 is my wifi)

Andrey.filippov: /* My wifi network is in 192.168.0.0/24 network */

2008-03-22T01:15:08Z

My wifi network is in 192.168.0.0/24 network

← Older revision		Revision as of 01:15, 22 March 2008
Line 71:		Line 71:
	== My wifi network is in 192.168.0.0/24 network ==		== My wifi network is in 192.168.0.0/24 network ==

	If your internet connection ~~truth~~ wifi is in 192.168.0.0/24 you can connect the camera restricting by the subnetwork.		If your internet connection trough wifi is in 192.168.0.0/24 you can connect the camera restricting by the subnetwork.

	sudo ifconfig eth1 192.168.0.15 netmask 255.255.255.248		sudo ifconfig eth1 192.168.0.15 netmask 255.255.255.248

Polto: /* Elphel 353 network config */

2008-03-21T23:28:16Z

Elphel 353 network config

← Older revision		Revision as of 23:28, 21 March 2008
Line 17:		Line 17:
	The default streamer configuration is to multicast on:		The default streamer configuration is to multicast on:
	232.8.1.33 port 20000		232.8.1.33 port 20000

			== MDI_MODE ==

			By default the camera is configured in auto MDI_MODE, so it can negotiate with the switch or the computer and use both normal and crossover ethernet cables. Sometimes the auto negotiation does not work for some reason, starting from 7.1.7.19 firmware you can set the MDI_MODE manually by adding:

			MDI_MODE=mdi
			or
			MDI_MODE=mdix
			or
			MDI_MODE=auto

			at the end of /etc/conf.d/net.eth0 configuration file.

	== ipsetd ==		== ipsetd ==
Line 45:		Line 57:

	The unit responds to the ping in the examples above if the new address was configured. Note, this method(ARP/ping mehtod above) only sets the IP address temporarily (while the unit is powered). To make the change permanent the ip paramters (IP address, subnet mask and gateway address) must be set in a file on the camera, otherwise the default network settings will be restored again when the board is rebooted and you will have to start all over again.		The unit responds to the ping in the examples above if the new address was configured. Note, this method(ARP/ping mehtod above) only sets the IP address temporarily (while the unit is powered). To make the change permanent the ip paramters (IP address, subnet mask and gateway address) must be set in a file on the camera, otherwise the default network settings will be restored again when the board is rebooted and you will have to start all over again.


	= Your PC network configuration =		= Your PC network configuration =

Polto: /* Serial Number/Ethernet Address */

2008-03-21T23:17:39Z

Serial Number/Ethernet Address

← Older revision		Revision as of 23:17, 21 March 2008
Line 5:		Line 5:
	== Serial Number/Ethernet Address ==		== Serial Number/Ethernet Address ==

	The ethernet address of the unit is the same as its serial number. The serial number is found on the label on the bottom of the camera.		The ethernet address of the unit is the same as its serial number. The serial number is found on the label on the bottom of the camera. You can also type

			ifconfig

			on the camera and look on the HWaddr address.

	== Default config ==		== Default config ==