Difference between revisions of "10393 manual"

From ElphelWiki
Jump to: navigation, search
(Known problems)
Line 1: Line 1:
 +
==Connections==
 +
* [[FPC_cables|sensors to system board]]
 
==Defaults==
 
==Defaults==
 
IP addr: 192.168.0.8
 
IP addr: 192.168.0.8
Line 42: Line 44:
 
  ...
 
  ...
  
 +
 +
==Temperature monitor==
 +
* http://192.168.0.8/hwmon.html:
 +
** T<sub>shutdown</sub> - automatic shutdown temperature level
 +
 +
==Proper shutdown==
 +
shutdown -hP now
 
==Known problems==
 
==Known problems==
 
* Vertical artifacts in jpegs. Images are ok at 100% quality. Fixed, testing.
 
* Vertical artifacts in jpegs. Images are ok at 100% quality. Fixed, testing.
* http://192.168.0.8:232x/noexif/mimg - multipart jpeg displays corrupted frames from time to time. Reason: network bandwidth? slow PC?
+
* http://192.168.0.8:232x/noexif/mimg - multipart jpeg displays corrupted frames from time to time. Reason: network bandwidth?
 
* Sometimes on power-on (NAND flash boot) cannot mount the card's rootfs partition. Kernel Panics. Power off/on. Soft "reboot -f" works ok.
 
* Sometimes on power-on (NAND flash boot) cannot mount the card's rootfs partition. Kernel Panics. Power off/on. Soft "reboot -f" works ok.
 
* Changing exposure/quality/gains - can corrupt images - needs testing.
 
* Changing exposure/quality/gains - can corrupt images - needs testing.

Revision as of 11:54, 19 May 2016

Connections

Defaults

IP addr: 192.168.0.8

user / pwd: root / <empty>

  • The address is set in the init_elphel393.sh script on the card's FAT32 partition.

Boot

  • on power-on boots from NAND flash: u-boot, device tree and kernel.

devicetree has "chosen = ...root=/dev/mmcblk0p2..." - rootfs is on the micro SD card second partition.

Command line access

ssh root@192.168.0.8

Serial console access

  • Use microUSB-USB cable to connect to PC - the cable's end should be thin enough otherwise interferes with the micro SD card.
  • Terminal: minicom -c on

(setup the device and speed - default settings might just work: /dev/ttyUSB0, 115200 8N1, No for hardware/software flow control)

Get images

channel 1: http://192.168.0.8:2323/noexif/img

channel 2: http://192.168.0.8:2324/noexif/img

channel 3: http://192.168.0.8:2325/noexif/img

channel 4: http://192.168.0.8:2326/noexif/img

Change parameters

  • http://192.168.0.8/controls.html - previews and basic parameters:
    • Exposure - the values are in the sensor lines.
    • WB - r,g,b gains
    • Quality - compression quality - individual for compressor but common for the buffer driver - it's better to have the same value for all channels.
  • The startup settings are defined int the local/verilog/startup on the micro SD card, FAT32 partition:
...
-c write_sensor_i2c  all 1 0 0x9009001e (exposure)
-c write_sensor_i2c  all 1 0 0x9035000a (set all gains to 0xa)
-c write_sensor_i2c  all 1 0 0x902c000e (blue gain to 0xe)
-c write_sensor_i2c  all 1 0 0x9009001d (red gain to 0xd)
...


Temperature monitor

Proper shutdown

shutdown -hP now

Known problems

  • Vertical artifacts in jpegs. Images are ok at 100% quality. Fixed, testing.
  • http://192.168.0.8:232x/noexif/mimg - multipart jpeg displays corrupted frames from time to time. Reason: network bandwidth?
  • Sometimes on power-on (NAND flash boot) cannot mount the card's rootfs partition. Kernel Panics. Power off/on. Soft "reboot -f" works ok.
  • Changing exposure/quality/gains - can corrupt images - needs testing.