Difference between revisions of "10393 manual"
From ElphelWiki
| Line 47: | Line 47: | ||
** Quality - compression quality - individual for compressor but common for the buffer driver - it's better to have the same value for all channels. | ** Quality - compression quality - individual for compressor but common for the buffer driver - it's better to have the same value for all channels. | ||
| − | * | + | * For 5MPix the startup settings are defined int the ''/usr/local/verilog/startup5'' on the micro SD card, FAT32 partition: |
... | ... | ||
-c write_sensor_i2c all 1 0 0x9009001e (exposure) | -c write_sensor_i2c all 1 0 0x9009001e (exposure) | ||
| Line 54: | Line 54: | ||
-c write_sensor_i2c all 1 0 0x9009001d (red gain to 0xd) | -c write_sensor_i2c all 1 0 0x9009001d (red gain to 0xd) | ||
... | ... | ||
| + | {| | ||
| + | |[[File:10393_controls.jpeg|thumb|200px]] | ||
| + | |} | ||
==Temperature monitor== | ==Temperature monitor== | ||
* http://192.168.0.8/hwmon.html: | * http://192.168.0.8/hwmon.html: | ||
** T<sub>shutdown</sub> - automatic shutdown temperature level | ** T<sub>shutdown</sub> - automatic shutdown temperature level | ||
| + | {| | ||
| + | |[[File:10393_hwmon.jpeg|thumb|200px]] | ||
| + | |} | ||
==Proper shutdown== | ==Proper shutdown== | ||
Revision as of 14:40, 19 May 2016
Contents
Connections
- sensors to system board
- Ports:
Defaults
IP addr: 192.168.0.8
user / pwd: root / <empty>
- The address is set in the init_elphel393.sh script on the card's FAT32 partition.
init_elphel393.sh
- Before boot set SENSOR_TYPE:
- SENSOR_TYPE=5 - for 5MPix sensors
- SENSOR_TYPE=14 - for 14MPix
NOTE: 5 & 14 MPix sensors cannot be mixed - require different bitstreams.
- Change the default IP address
Boot
- on power-on boots from NAND flash: u-boot, device tree and kernel.
devicetree has "chosen = ...root=/dev/mmcblk0p2..." - rootfs is on the micro SD card second partition.
Command line access
ssh root@192.168.0.8
Serial console access
- Use microUSB-USB cable to connect to PC - the cable's end should be thin enough otherwise interferes with the micro SD card.
- Terminal: minicom -c on
(setup the device and speed - default settings might just work: /dev/ttyUSB0, 115200 8N1, No for hardware/software flow control)
Get images
channel 1: http://192.168.0.8:2323/noexif/img
channel 2: http://192.168.0.8:2324/noexif/img
channel 3: http://192.168.0.8:2325/noexif/img
channel 4: http://192.168.0.8:2326/noexif/img
Change parameters
- http://192.168.0.8/controls.html - previews and basic parameters:
- Exposure - the values are in the sensor lines.
- WB - r,g,b gains
- Quality - compression quality - individual for compressor but common for the buffer driver - it's better to have the same value for all channels.
- For 5MPix the startup settings are defined int the /usr/local/verilog/startup5 on the micro SD card, FAT32 partition:
... -c write_sensor_i2c all 1 0 0x9009001e (exposure) -c write_sensor_i2c all 1 0 0x9035000a (set all gains to 0xa) -c write_sensor_i2c all 1 0 0x902c000e (blue gain to 0xe) -c write_sensor_i2c all 1 0 0x9009001d (red gain to 0xd) ...
Temperature monitor
- http://192.168.0.8/hwmon.html:
- Tshutdown - automatic shutdown temperature level
Proper shutdown
shutdown -hP now
Firmware image
Known problems
- Vertical artifacts in jpegs. Images are ok at 100% quality. Fixed, testing.
- http://192.168.0.8:232x/noexif/mimg - multipart jpeg displays corrupted frames from time to time. Reason: network bandwidth?
- Sometimes on power-on (NAND flash boot) cannot mount the card's rootfs partition. Kernel Panics. Power off/on. Soft "reboot -f" works ok.
- Changing exposure/quality/gains - can corrupt images - needs testing.
