Difference between revisions of "10393 manual"
From ElphelWiki
| Line 1: | Line 1: | ||
| − | ==Connections== | + | ==<font color="blue">Connections</font>== |
* Connect [[FPC_cables|sensors to system board]] - FPC cables are not symmetrical | * Connect [[FPC_cables|sensors to system board]] - FPC cables are not symmetrical | ||
* Ports: | * Ports: | ||
| Line 5: | Line 5: | ||
|[[File:NC393-CS marked ports.jpeg|thumb|200px]] | |[[File:NC393-CS marked ports.jpeg|thumb|200px]] | ||
|} | |} | ||
| − | ==Defaults== | + | ==<font color="blue">Defaults</font>== |
IP addr: 192.168.0.8 | IP addr: 192.168.0.8 | ||
| Line 12: | Line 12: | ||
* The address is set in the ''init_elphel393.sh'' script on the card's FAT32 partition. | * The address is set in the ''init_elphel393.sh'' script on the card's FAT32 partition. | ||
| − | ==init_elphel393.sh== | + | ==<font color="blue">init_elphel393.sh</font>== |
* Before boot set SENSOR_TYPE: | * Before boot set SENSOR_TYPE: | ||
** SENSOR_TYPE=5 - for 5MPix sensors | ** SENSOR_TYPE=5 - for 5MPix sensors | ||
| Line 19: | Line 19: | ||
* Change the default IP address | * Change the default IP address | ||
| − | ==Boot== | + | ==<font color="blue">Boot</font>== |
* on power-on boots from NAND flash: u-boot, device tree and kernel. | * on power-on boots from NAND flash: u-boot, device tree and kernel. | ||
devicetree has "chosen = ...root=/dev/mmcblk0p2..." - rootfs is on the micro SD card second partition. | devicetree has "chosen = ...root=/dev/mmcblk0p2..." - rootfs is on the micro SD card second partition. | ||
| − | ==Command line access== | + | ==<font color="blue">Command line access</font>== |
ssh root@192.168.0.8 | ssh root@192.168.0.8 | ||
| − | ==Serial console access== | + | ==<font color="blue">Serial console access</font>== |
* Use microUSB-USB cable to connect to PC - the cable's end should be thin enough otherwise interferes with the micro SD card. | * Use microUSB-USB cable to connect to PC - the cable's end should be thin enough otherwise interferes with the micro SD card. | ||
| Line 32: | Line 32: | ||
(setup the device and speed - default settings might just work: /dev/ttyUSB0, 115200 8N1, No for hardware/software flow control) | (setup the device and speed - default settings might just work: /dev/ttyUSB0, 115200 8N1, No for hardware/software flow control) | ||
| − | ==Get images== | + | ==<font color="blue">Get images</font>== |
channel 1: http://192.168.0.8:2323/noexif/img | channel 1: http://192.168.0.8:2323/noexif/img | ||
| Line 41: | Line 41: | ||
channel 4: http://192.168.0.8:2326/noexif/img | channel 4: http://192.168.0.8:2326/noexif/img | ||
| − | ==Change parameters== | + | ==<font color="blue">Change parameters</font>== |
* http://192.168.0.8/controls.html - previews and basic parameters: | * http://192.168.0.8/controls.html - previews and basic parameters: | ||
** Exposure - the values are in the sensor lines. | ** Exposure - the values are in the sensor lines. | ||
| Line 58: | Line 58: | ||
|} | |} | ||
| − | ==Temperature monitor== | + | ==<font color="blue">Temperature monitor</font>== |
* http://192.168.0.8/hwmon.html: | * http://192.168.0.8/hwmon.html: | ||
** T<sub>shutdown</sub> - automatic shutdown temperature level | ** T<sub>shutdown</sub> - automatic shutdown temperature level | ||
| Line 65: | Line 65: | ||
|} | |} | ||
| − | ==Proper shutdown== | + | ==<font color="blue">Proper shutdown</font>== |
shutdown -hP now | shutdown -hP now | ||
| − | ==Firmware image== | + | ==<font color="blue">Firmware image</font>== |
* [http://community.elphel.com/files/393/20160526/ 20160526 (new)] | * [http://community.elphel.com/files/393/20160526/ 20160526 (new)] | ||
* [http://community.elphel.com/files/393/20160524/ 20160524 (old)] | * [http://community.elphel.com/files/393/20160524/ 20160524 (old)] | ||
* [http://community.elphel.com/files/393/20160519/ 20160519 (old)] | * [http://community.elphel.com/files/393/20160519/ 20160519 (old)] | ||
| − | ==Known problems== | + | ==<font color="blue">Known problems</font>== |
* Vertical artifacts in jpegs. Images are ok at 100% quality. Fixed, testing. | * Vertical artifacts in jpegs. Images are ok at 100% quality. Fixed, testing. | ||
* http://192.168.0.8:232x/noexif/mimg - multipart jpeg displays corrupted frames from time to time. Reason: network bandwidth? | * http://192.168.0.8:232x/noexif/mimg - multipart jpeg displays corrupted frames from time to time. Reason: network bandwidth? | ||
Revision as of 10:58, 31 May 2016
Contents
Connections
- Connect sensors to system board - FPC cables are not symmetrical
- Ports:
Defaults
IP addr: 192.168.0.8
user / pwd: root / <empty>
- The address is set in the init_elphel393.sh script on the card's FAT32 partition.
init_elphel393.sh
- Before boot set SENSOR_TYPE:
- SENSOR_TYPE=5 - for 5MPix sensors
- SENSOR_TYPE=14 - for 14MPix
NOTE: 5 & 14 MPix sensors cannot be mixed - require different bitstreams.
- Change the default IP address
Boot
- on power-on boots from NAND flash: u-boot, device tree and kernel.
devicetree has "chosen = ...root=/dev/mmcblk0p2..." - rootfs is on the micro SD card second partition.
Command line access
ssh root@192.168.0.8
Serial console access
- Use microUSB-USB cable to connect to PC - the cable's end should be thin enough otherwise interferes with the micro SD card.
- Terminal: minicom -c on
(setup the device and speed - default settings might just work: /dev/ttyUSB0, 115200 8N1, No for hardware/software flow control)
Get images
channel 1: http://192.168.0.8:2323/noexif/img
channel 2: http://192.168.0.8:2324/noexif/img
channel 3: http://192.168.0.8:2325/noexif/img
channel 4: http://192.168.0.8:2326/noexif/img
Change parameters
- http://192.168.0.8/controls.html - previews and basic parameters:
- Exposure - the values are in the sensor lines.
- WB - r,g,b gains
- Quality - compression quality - individual for compressor but common for the buffer driver - it's better to have the same value for all channels.
- For 5MPix the startup settings are defined int the /usr/local/verilog/startup5 on the micro SD card, FAT32 partition:
... -c write_sensor_i2c all 1 0 0x9009001e (exposure) -c write_sensor_i2c all 1 0 0x9035000a (set all gains to 0xa) -c write_sensor_i2c all 1 0 0x902c000e (blue gain to 0xe) -c write_sensor_i2c all 1 0 0x9009001d (red gain to 0xd) ...
Temperature monitor
- http://192.168.0.8/hwmon.html:
- Tshutdown - automatic shutdown temperature level
Proper shutdown
shutdown -hP now
Firmware image
Known problems
- Vertical artifacts in jpegs. Images are ok at 100% quality. Fixed, testing.
- http://192.168.0.8:232x/noexif/mimg - multipart jpeg displays corrupted frames from time to time. Reason: network bandwidth?
- Sometimes on power-on (NAND flash boot) cannot mount the card's rootfs partition. Kernel Panics. Power off/on. Soft "reboot -f" works ok.
- Changing exposure/quality/gains - can corrupt images - needs testing.
