Difference between revisions of "Poky migration from rocko to warrior"

Revision as of 09:06, 1 August 2019

Elphel's kernel tree

.
├── arch
│   └── arm
│       └── boot
│           └── dts/ # device trees for 393 cameras, considering tested
├── drivers
│   ├── ata
│   │   ├── ahci_elphel.c # tested reading and writing from/to SSD
│   │   └── libata-eh.c
│   ├── char
│   │   └── xilinx_devcfg.c # tested bitstream loading - brought back the old character device driver, it's simpler this way than the new one FPGA manager that can load only .bit.bin files
│   ├── clk
│   │   └── clk-si5338.c # chip found, no errors
│   ├── elphel
│   │   ├── circbuf.c # tested via recording
│   │   ├── clock10359.c
│   │   ├── command_sequencer.c # ok
│   │   ├── cxi2c.c
│   │   ├── detect_sensors.c
│   │   ├── elphel393-init.c # ok
│   │   ├── elphel393-mem.c # ok
│   │   ├── elphel393-pwr.c # ok
│   │   ├── exif393.c
│   │   ├── fpgajtag353.c
│   │   ├── framepars.c # ok
│   │   ├── gamma_tables.c # affects images which look ok
│   │   ├── histograms.c # displayed
│   │   ├── imu_log393.c
│   │   ├── jpeghead.c
│   │   ├── klogger_393.c
│   │   ├── lepton.c
│   │   ├── mt9f002.c
│   │   ├── mt9x001.c # sensor is programmed correctly
│   │   ├── multi10359.c
│   │   ├── pgm_functions.c # parameters are getting applied correctly (mt9p006)
│   │   ├── quantization_tables.c # images not broken
│   │   ├── sensor_common.c
│   │   ├── sensor_i2c.c
│   │   ├── x393.c
│   │   ├── x393_fpga_functions.c # ok
│   │   └── x393_videomem.c # also used in circbuf => recording => works
│   ├── misc
│   │   ├── ltc3589.c
│   │   └── vsc330x.c # switching between internal and external SSD ports works
│   ├── mmc
│   │   └── host
│   │       └── sdhci.c # this needed chip detect ORed with dat3: SDHCI_ANY_PRESENT = SDHCI_CARD_PRESENT | SDHCI_DAT3_PRESENT
│   ├── mtd
│   │   └── nand # added functions to work with OTP, tested only reading
│   │       ├── nand_base.c
│   │       ├── nandchip-micron.c
│   │       └── pl35x_nand.c
│   ├── net
│   │   └── ethernet
│   │       └── cadence
│   │           └── macb_main.c # needed fixup for Atheros chip - disable SmartEEE
│   └── rtc
│       └── rtc-m41t80.c # updated to latest version. Our changes only ignore Oscillator failure at boot at m41t80_get_datetime().
├── helpers
│   └── si5338_register_map_dts.py # test it?
├── other
│   └── mem.py
└── patches
    ├── ahci.patch
    ├── drivers-elphel.patch
    ├── garmin_usb.c.patch
    └── libahci.patch

[SOLVED] Note 1: Bring back fpga char device

• /dev/xdevfg got obsolete - there's fpga manager instead which cannot load *.bit (only *.bin or *.bit.bin)
• Solution:

Brought back the old driver (drivers/char/xilinx_devcfg.c and edited Kconfig and Makefile)- it works as it used to

[SOLVED] Note 2: Build php 5.6.40

• php 5.6.40 - EOL and won't build - mysql supposedly moved header files.
• Solution:

Disabled mysql extension:
To meta-elphel393/recipes-devtools/php/php_5.6.%.bbappend:
    PACKAGECONFIG[mysql] = "--without-mysql --without-mysqli --without-pdo-mysql"
    CFLAGS += " -ldl"

[SOLVED] Note 3: Entropy device hwrng

• New package rng-tools is whining: Failed to init entropy source hwrng
• Solution:

Leave as is for now. The full log is:
Initalizing available sources
Failed to init entropy source hwrng
Enabling JITTER rng support
Initalizing entropy source jitter

• Comments:
  • Haven't found if Xilinx uses any driver for /dev/hwrng
  • TODO: Find out if the order of entropy sources can be changed

- Note 4: PHP causing 'unsupported FP instruction in kernel mode'

• autocampars.php runs at boot and sometimes causes Kernel Oops:

[   35.872118] BUG: unsupported FP instruction in kernel mode
[   35.877621] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[   35.883380] Modules linked in:
[   35.886498] CPU: 1 PID: 1756 Comm: php Not tainted 4.14.0-xilinx-v2018.3 #1
[   35.893459] Hardware name: Xilinx Zynq Platform
[   35.897989] task: ee83f280 task.stack: ef1d6000
[   35.902527] PC is at vfp_reload_hw+0x30/0x44
[   35.906802] LR is at __und_usr_fault_32+0x0/0x8
[   35.911338] pc : [<c0102e10>]    lr : [<c010c280>]    psr: a0000013
[   35.917529] sp : ef1d7fb0  ip : 00000051  fp : 00000001
[   35.922813] r10: ef1d61f8  r9 : c010c308  r8 : ee9893c0
[   35.928040] r7 : 00000001  r6 : 00400100  r5 : c0138d08  r4 : ecd600f8
[   35.934569] r3 : c0c6c064  r2 : b67bde8c  r1 : ecd9a224  r0 : eeb00a40
[   35.941098] Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
[   35.948241] Control: 18c5387d  Table: 2cda404a  DAC: 00000051
[   35.953993] Process php (pid: 1756, stack limit = 0xef1d6210)
[   35.959740] Stack: (0xef1d7fb0 to 0xef1d8000)
[   35.964020] 7fa0:                                     a5f43f50 a5f43e18 00000080 00000000
[   35.972269] 7fc0: 00000000 a5f43f4c b687b338 000000ae 00000000 bedcdfe4 00000001 a5f43ffc
[   35.980385] 7fe0: a5f43f50 a5f43d7c b676cf78 b67bde8c 60000010 ffffffff 00000000 00000000
[   35.988626] Code: 128aa080 e89a0162 e3110102 0a000003 (eee96a10) 
[   35.994724] ---[ end trace 06029778db6d2d90 ]---
[   35.999422] note: php[1756] exited with preempt_count 2

Unsupported floating point instruction in kernel?

• Is it hardware (some faulty board? temperature based?) or kernel or php?

• solution?:

Took arch/vfp/vfpmodule.c from kernel 4.19
The current was 4.14
It didn't work. Roll back and check which php call caused it?

• TODO: keep an eye on this, because the real reason is not investigated

[SOLVED] Note 5: Bring up NAND OTP support

• MAC is not read from NAND, displays the default: 00:0e:64:10:00:00
• Problem?

[    3.639851] elphel393-init: Flash page read, code -95

• Comments:
  • Lookup what had changed.
• Solution: (for xlnx_rebase_v4.14 branch of linux-xlnx):

In drivers/mtd/nand_base.c in nand_scan_tail() they call nand_manufacturer_init()
which is mapped to a new driver drivers/mtd/nand_micron.c.
So, when it fails - the driver init fails - mtd functions do not get assigned. 
(And the driver (drivers/elphel/elphel393_init.c) that reads from OTP area returns
-95 which is EOPNOTSUPP.)
We just need to fall through for a quick fix.

The reason that function exits with an error is it decides that it does not support
forcefully enabled on-die ECC. And this needs to be investigated.

[SOLVED] Note 6: udev - unknown group 'kvm'

• Problem:

[    5.817352] udevd[1478]: starting version 3.2.7
[    5.918028] udevd[1478]: specified group 'kvm' unknown
[    5.986364] udevd[1479]: starting eudev-3.2.7
[    6.142897] udevd[1479]: specified group 'kvm' unknown

• Solution:

KVM == Kernel-based Virtual Machine. Remove for now (and maybe forever)
.
└── udev
    ├── eudev
    │   └── 50-udev-default.rules
    └── eudev_3.2.7.bbappend

50-udev-default.rules - gets installed over the original file.

[SOLVED] Note 7: Add back fixup for Atheros to updated ethernet driver

• Problem:

Ethernet driver's structure has changed. It was split into several files.
Lives at /driver/net/ethernet/cadence/

• Soluton:

For out ethernet chip (Atheros 80xx) a fixup had to be added to disable SmartEEE.
It's a single function, call and a couple defines - added all back to the new driver structure.

[SOLVED] Note 8: u-boot update

• update u-boot
• solution:

Updated to 2019.07 mainstream u-boot
- converted our *.h (with params used to generate SPL header) to Kconfigs
- updated driver for NAND flash - tested both boot modes - mmc and nand

[SOLVED] Note 9: test camogm

• test camogm

/var/state/camogm_cmd accepts only the first write - switch to polling?
when switched to polling - when recording - buffer gets overflow. Because the polling version does not work correctly probably.
All is working for the version without polling - after adding EOF reset (clearerr(npipe)) right after reading from the pipe and checking if feof().

[SOLVED] Note 10: test streamer

• test streamer

Streamer works

[SOLVED] Note 11: test AHCI driver

• test ahci driver
• results:

- SSD is detected and automounted
- write/read works

- Note 12: test raw recording

• test recording on a raw partition