Difference between revisions of "10349"
From ElphelWiki
(→Next revision) |
(add description of socket) |
||
| Line 8: | Line 8: | ||
* 2 socket for external usermade board | * 2 socket for external usermade board | ||
* some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing. | * some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing. | ||
| + | |||
| + | === Socket description === | ||
| + | |||
| + | * internal USB2, USB3, USB4 | ||
| + | * 1 - power | ||
| + | * 2 - D- | ||
| + | * 3 - D+ | ||
| + | * 4 - GND | ||
| + | |||
| + | * J7 is the serial port | ||
| + | * 1 - RX | ||
| + | * 2 - TX | ||
| + | * 3 - CTS | ||
| + | * 4 - RTS | ||
| + | * 5 - GND | ||
| + | * 6 - removed, used as key | ||
| + | |||
| + | * J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires. | ||
| + | |||
| + | * J5 for connect external boards | ||
| + | * 1 - EXT0 (FPGA IO signal) | ||
| + | * 2 - EXT1 (FPGA IO signal) | ||
| + | * 3 - EXT2 (FPGA IO signal) | ||
| + | * 4 - EXT3 (FPGA IO signal) | ||
| + | * 5 - EXT4 (FPGA IO signal) | ||
| + | * 6 - GND | ||
| + | * 7 - EXT5 (FPGA IO signal) | ||
| + | * 8 - GND | ||
| + | * 9 - +3.3V | ||
| + | * 10 - +3.3V | ||
| + | * 11 - CTS (TTL level) | ||
| + | * 12 - RTS (TTL level) | ||
| + | * 13 - RX (TTL level) | ||
| + | * 14 - TX (TTL level) | ||
| + | * 15 - not connected | ||
| + | * 16 - not connected | ||
=== Power description === | === Power description === | ||
Revision as of 12:44, 11 September 2007
Russia page 10349.Ru
Contents
Interface board.
- serial port
- 4 ports USB hub with 3 internal, 1 external USB ports
- IDE port for the 1.8" hard drive with ZIF Flat cable
- 2 socket for external usermade board
- some points for soldering wires directly to board (from external board to 10349 for example), easy hardware developing.
Socket description
* internal USB2, USB3, USB4 * 1 - power * 2 - D- * 3 - D+ * 4 - GND
* J7 is the serial port * 1 - RX * 2 - TX * 3 - CTS * 4 - RTS * 5 - GND * 6 - removed, used as key
* J4 for connect external boards. All wires of J4 connected to the solder pads. For make connection via wires.
* J5 for connect external boards * 1 - EXT0 (FPGA IO signal) * 2 - EXT1 (FPGA IO signal) * 3 - EXT2 (FPGA IO signal) * 4 - EXT3 (FPGA IO signal) * 5 - EXT4 (FPGA IO signal) * 6 - GND * 7 - EXT5 (FPGA IO signal) * 8 - GND * 9 - +3.3V * 10 - +3.3V * 11 - CTS (TTL level) * 12 - RTS (TTL level) * 13 - RX (TTL level) * 14 - TX (TTL level) * 15 - not connected * 16 - not connected
Power description
It has DC-DC converter 3.3V->5V 1.5A. Each USB port has current limit to 300mA. Each port is overcurrent protected via USB power distributed systems. Use both IDE hard drive with USB devices can be overload Power over Ethernet equipment. Use external additional power injector.
Kit for Developers
- for serial cable - connector A3B-6D-2C (Digi-Key) - 1 + half of AE9873-ND (Digi-Key) - 1
- for internal USB sockets - AE10179-ND (Digi-Key) - 1
- for additional boards connectors 3M5311-ND (thru-hole 2mm, Digi-Key) - 2
- or for additional boards connectors 3M5309CT-ND (SMD, Digi-Key) - 2
- blank PCB board V1255-ND (Digi-Key) - 1
Next revision
In new revision of this board we want use much more IDE interfaces.
* IDE port for a 2.5" hard drive * IDE port for CompactFlash card * IDE port a 1.8" hard drive with ZIF Flat cable * SATA port
For make SATA port we can use IDE<->SATA bridge or soft IP core in a FPGA.
IDE-SATA bridges:
* JMicron [JM20330] (send email, no answer) * Marvell [88i8030, 88SA8040] (need sign NDA, sucks) * Silicon Image [SiI3611] (Available only through your local sales contact. send email, no answer) * Atmel [AT78C5010] (Available only through your local sales contact. send email, no answer) * ACARD [ARC-770] (Available only through your local sales contact. send email, no answer)
Now I can`t found any datasheets for this. It`s a big secret of a company :(
