Difference between revisions of "Porting Theora to 353 cameras"
(→System Interface) |
(→Compressor) |
||
(57 intermediate revisions by 2 users not shown) | |||
Line 8: | Line 8: | ||
Dealing with the last solution seems to be a good start for this project as the other features mentioned can be added later. In all cases, both FPGA code and software code will need to be adapted. | Dealing with the last solution seems to be a good start for this project as the other features mentioned can be added later. In all cases, both FPGA code and software code will need to be adapted. | ||
− | + | The source code of this project is available at [http://elphel.cvs.sourceforge.net/elphel/fpga/theora_353/ http://elphel.cvs.sourceforge.net/elphel/fpga/theora_353/] | |
== Hardware updates == | == Hardware updates == | ||
=== Compressor === | === Compressor === | ||
+ | [[Image:Schematic.png|frame|[[Media:Schematic.png|333 Theora design with the 2 stage compressor and the 8-channel memory controller]]]] | ||
Replace the MJPEG compressor in the 353 with the 333 Theora compressor ([http://elphel.cvs.sourceforge.net/elphel/camera333/fpga/x333 333 Theora FPGA code]). Maybe some adaptations need to be done within the Theora compressor itself. However, assuming that the compressor worked in 333 cameras a simple instantiation should suffice. | Replace the MJPEG compressor in the 353 with the 333 Theora compressor ([http://elphel.cvs.sourceforge.net/elphel/camera333/fpga/x333 333 Theora FPGA code]). Maybe some adaptations need to be done within the Theora compressor itself. However, assuming that the compressor worked in 333 cameras a simple instantiation should suffice. | ||
=== Memory controller === | === Memory controller === | ||
− | Replace the 4-channel memory controller with an 8 | + | Replace the 4-channel memory controller with an 8 channel memory interface as in the 333 model in order to handle Theora specific data. |
− | {| | + | {|border="1" cellpadding="2" |
! Channel !! 333 Theora !! 353 | ! Channel !! 333 Theora !! 353 | ||
|- | |- | ||
Line 37: | Line 38: | ||
|- | |- | ||
|} | |} | ||
+ | |||
+ | === Sensor interface === | ||
+ | ''sensorpix'' block must be adapted in order to provide a coherent interface between the memory controller and the sensor (channels 0 and 1) | ||
+ | |||
=== System Interface === | === System Interface === | ||
Line 57: | Line 62: | ||
− | |||
− | {| | + | ''353 system interface address table'' |
+ | {|border="1" cellpadding="2" | ||
! Address !! da signal !! Comments | ! Address !! da signal !! Comments | ||
|- | |- | ||
Line 87: | Line 92: | ||
|- | |- | ||
| '''0x0f''' || twr0 || write tables data | | '''0x0f''' || twr0 || write tables data | ||
+ | |- | ||
+ | | '''0x10''' || || Status register | ||
|- | |- | ||
| '''0x1b''' || dcmrst || async signal to restart DCMs (if irnw=0) | | '''0x1b''' || dcmrst || async signal to restart DCMs (if irnw=0) | ||
Line 108: | Line 115: | ||
|} | |} | ||
− | |||
− | {| | + | ''333 system interface address table'' |
+ | {|border="1" cellpadding="2" | ||
! Address !! da signal !! Comments | ! Address !! da signal !! Comments | ||
|- | |- | ||
Line 142: | Line 149: | ||
|- | |- | ||
|} | |} | ||
− | + | ||
− | + | Addresses 0x01,2,3,4,5,6,8 and 0x30 can be kept in the 353 system interface. The interrupt mask address 0x06 in the 333 sys interface is no longer used (353 uses interrupt vectors). The Theora compressor and the new memory controller addresses have to be mapped again in the new design (addresses 0x0c..0x0d and 0x20 to 0x2f in the 353 sys interface). | |
=== Interrupts === | === Interrupts === | ||
Adapt the Theora compressor interrupts to the 353 interrupt vector . | Adapt the Theora compressor interrupts to the 353 interrupt vector . | ||
− | The 353 interrupt vector can handle up to 16 different irq. However, only irq 0 to | + | The 353 interrupt vector can handle up to 16 different irq. However, only irq 0 to 7 are used : |
'''x353.v''' | '''x353.v''' | ||
Line 171: | Line 178: | ||
=== DMA FIFOs === | === DMA FIFOs === | ||
353 design uses 2 DMA FIFOs between the compressor and the system interface instead of one for the 333 Theora compressor. The two DMA FIFOs have also slight differences between the two design. Maybe a single 333 FIFO should be kept for the final design (?) | 353 design uses 2 DMA FIFOs between the compressor and the system interface instead of one for the 333 Theora compressor. The two DMA FIFOs have also slight differences between the two design. Maybe a single 333 FIFO should be kept for the final design (?) | ||
+ | |||
+ | === FPGA -> CPU data out MUX === | ||
+ | The purpose of this MUX is to route data out from the different FPGA blocks to the system interface and then to the data bus to the CPU. The selection is made with the internal address bus ''ia''. | ||
+ | _ | ||
+ | --| \ | ||
+ | --| | | ||
+ | --| | | ||
+ | --| |--- iod[31:0] -> to system interface | ||
+ | --| | | ||
+ | --| | | ||
+ | |_/ | ||
+ | from system interface -> ia[7:0]__| | ||
+ | |||
+ | |||
+ | '' 333 MUX '' | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! Adress range !! ia(5) !! ia(4) !! iod[31:0] !! Comments | ||
+ | |- | ||
+ | | '''0x0..''' || '''0''' || '''0''' || dma_d[31:0] || DMA data | ||
+ | |- | ||
+ | | '''0x1..''' || '''0''' || '''1''' || rd_regs[31:0] || Data from internal registers | ||
+ | |- | ||
+ | | '''0x2..''' || '''1''' || '''0''' || {8'h0,xfer_bytes[23:0]} || Frame length (in bytes) | ||
+ | |- | ||
+ | | '''0x3..''' || '''1''' || '''1''' || bdo[31:0] || 32-bit data from SDRAM channel 3 | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | |||
+ | '' 353 MUX '' | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! Address !! ia(6) !! ia(5) !! ia(4) !! ia(2) !! ia(0) !! iod[31:0] !! Comments | ||
+ | |- | ||
+ | | '''0x0.. (even)''' || '''0''' || '''0''' || '''0''' || '''X''' || '''0''' || dma_d0[31:0] || DMA 0 data | ||
+ | |- | ||
+ | | '''0x0.. (odd)''' || '''0''' || '''0''' || '''0''' || '''X''' || '''1''' || dma_d1[31:0] || DMA 1 data | ||
+ | |- | ||
+ | | '''0x1..''' || '''0''' || '''0''' || '''1''' || '''X''' || '''X''' || rd_regs[31:0] || Data from internal registers | ||
+ | |- | ||
+ | | '''0x2..''' || '''0''' || '''1''' || '''0''' || '''X''' || '''X''' || dsdo[31:0] || Data out from descriptor memory | ||
+ | |- | ||
+ | | '''0x3..''' || '''0''' || '''1''' || '''1''' || '''X''' || '''X''' || bdo[31:0] || 32-bit data from SDRAM channel3 | ||
+ | |- | ||
+ | | '''0x40..0x43''' || '''1''' || '''0''' || '''X''' || '''0''' || '''X''' || hist_do[31:0] || Histogram data out, actully only [17:0] | ||
+ | |- | ||
+ | | '''0x44''' || '''1''' || '''0''' || '''X''' || '''1''' || '''0''' || {12'h0,pio_usec[19:0]} || usec output from RTC | ||
+ | |- | ||
+ | | '''0x45''' || '''1''' || '''0''' || '''X''' || '''1''' || '''1''' || pio_sec[31:0] || sec output from RTC | ||
+ | |- | ||
+ | | '''0x6..''' || '''1''' || '''1''' || '''0''' || '''X''' || '''X''' || 32'h0 || 0x0000 | ||
+ | |- | ||
+ | | '''0x7..''' || '''1''' || '''1''' || '''1''' || '''X''' || '''X''' || {14'b0,xfpgatdo,xfpgastat,4'b0,io_pins[11:0]} || TDO read from an external FPGA / Multiplexed read data from xjtag / Status of 12 i/o pins | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === Internal registers MUX and status register === | ||
+ | |||
+ | |||
+ | '' 333 MUX '' | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! Address || ia(1) !! ia(0) !! rd_regs[31:0] !! Comments | ||
+ | |- | ||
+ | | '''0x10''' || '''0''' || '''0''' || Status register || See below | ||
+ | |- | ||
+ | | '''0x11''' || '''0''' || '''1''' || {24'b0,irqr[7:0]} || Interrupts | ||
+ | |- | ||
+ | | '''0x12''' || '''1''' || '''0''' || {5'b0,trig_v[10:0],4'b0,trig_h[11:0]} || Trigger phase | ||
+ | |- | ||
+ | | '''0x13''' || '''1''' || '''1''' || MODELREV || Model revision | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | '' 353 MUX '' | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! Address !! ia(2) !! ia(1) !! ia(0) !! rd_regs[31:0] !! Comments | ||
+ | |- | ||
+ | | '''0x10''' || '''0''' || '''0''' || '''0''' || Status register || See below | ||
+ | |- | ||
+ | | '''0x11''' || '''0''' || '''0''' || '''1''' || irqr[31:0] || Interrupts | ||
+ | |- | ||
+ | | '''0x12''' || '''0''' || '''1''' || '''0''' || {5'b0,trig_v[10:0],4'b0,trig_h[11:0]} || Trigger phase | ||
+ | |- | ||
+ | | '''0x13''' || '''0''' || '''1''' || '''1''' || MODELREV || Model revision | ||
+ | |- | ||
+ | | '''0x14''' || '''1''' || '''X''' || '''0''' || {8'h0,imgptr[23:0]} || Image pointer in 32-byte chunks | ||
+ | |- | ||
+ | | '''0x15''' || '''1''' || '''X''' || '''1''' || hifreq[31:0] || Accumulated high-freq components | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | |||
+ | '' 333 status register '' | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! Bit # !! Signal !! Comments | ||
+ | |- | ||
+ | | '''0''' || sr_sda0 || I2C to sensor | ||
+ | |- | ||
+ | | '''1''' || sr_scl0 || I2C clock0 | ||
+ | |- | ||
+ | | '''2''' || sr_sda1 || I2C | ||
+ | |- | ||
+ | | '''3''' || sr_scl1 || I2C clock1 | ||
+ | |- | ||
+ | | '''4..12''' || rq_busy[8:0] || Request or busy - per mcontr channel | ||
+ | |- | ||
+ | | '''13..15''' || sr_sensortrig[2:0] || x00 - idle, x01 - waiting vacts to start, x10 - waiting for trigger, x11 - frame over ,1xx - frame done (reset by writing command to sensor_trig | ||
+ | |- | ||
+ | | '''16''' || sr_memrdy || Ready to r/w next 8x32 page (channel 3) CPU<->SDRAM | ||
+ | |- | ||
+ | | '''17''' || sr_wrempty || CPU write buffer empty (valid only in write mode) | ||
+ | |- | ||
+ | | '''18''' || 1'b0 || 0x0 | ||
+ | |- | ||
+ | | '''19''' || dma_empty || dma output buffer empty and dma is enabled (pessimistic - with delay) | ||
+ | |- | ||
+ | | '''20''' || itrig || TRIG input | ||
+ | |- | ||
+ | | '''21..22''' || dcm_err[1:0] || 00 - no data (SDRAM reads) since last change (wclk*wcmd) | ||
+ | , 01 - clock is too late | ||
+ | , 10 - clock is too early | ||
+ | , 11 - OK (some measurements show too late, some - too early) | ||
+ | |- | ||
+ | | '''23''' || dcm_done || | ||
+ | |- | ||
+ | | '''24''' || sr_pipe_rdy || Will go active with delay to overlap with DMA busy (external) | ||
+ | |- | ||
+ | | '''25''' || sr_pipe_nempty || Compressor pipe not empty (updated with done -> IRQ) | ||
+ | |- | ||
+ | | '''26''' || sr_pipe_full || Compressor pipe has 3 frame compress commands in the input queue/in progress | ||
+ | |- | ||
+ | | '''27''' || en_refresh || Status bit to find out if SDRAM is programmed | ||
+ | |- | ||
+ | | '''28''' || tok_frame_num_wr || Odd/even frame of tokens written | ||
+ | |- | ||
+ | | '''29''' || 1'b0 || 0x0 | ||
+ | |- | ||
+ | | '''30''' || debug_out || Debug shift register output | ||
+ | |- | ||
+ | | '''31''' || 'b0 || 0x0 | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | '' 353 status register '' | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! Bit # !! Signal !! Comments | ||
+ | |- | ||
+ | | '''0''' || sr_sda0 || I2C to sensor | ||
+ | |- | ||
+ | | '''1''' || sr_scl0 || I2C clock | ||
+ | |- | ||
+ | | '''2''' || sr_ch0rdy || Ready to write next page (channel 0) SENSOR->SDRAM | ||
+ | |- | ||
+ | | '''3''' || sr_ch1rdy || Ready to read next page (channel 1) SDRAM->FPN(SENSOR) | ||
+ | |- | ||
+ | | '''4''' || sr_ch2rdy || Ready to read next page (channel 2) SDRAM->DMA | ||
+ | |- | ||
+ | | '''5''' || sr_memrdy || Ready to r/w next 8x32 page (channel 3) CPU<->SDRAM | ||
+ | |- | ||
+ | | '''6''' || sr_wrempty || CPU write buffer empty (valid only in write mode). May reprogram channel3. | ||
+ | |- | ||
+ | | '''7..10''' || sr_nextFrame[3:0] || (level) generated before actual block is filled - needed to be combined with the pulse from buffer control | ||
+ | |- | ||
+ | | '''11..13''' || sr_sensortrig[2:0] || x00 - idle, x01 - waiting vacts to start, x10 - waiting for trigger, x11 - frame over ,1xx - frame done (reset by writing command to sensor_trig | ||
+ | |- | ||
+ | | '''14''' || dcc_rdy || 128 of DC components from JPEG encoder are available (same as interrupt) | ||
+ | |- | ||
+ | | '''15''' || compressor_done_input || will go high after EOT and persist until DCT is enabled | ||
+ | |- | ||
+ | | '''16''' || compressor_done_compress || will go high after all data is sent out | ||
+ | |- | ||
+ | | '''17''' || dma_empty || dma output buffer empty and dma is enabled (pessimistic - with delay) | ||
+ | |- | ||
+ | | '''19..18''' || dcm_err[1:0] || SDRAM DCM phase error | ||
+ | |- | ||
+ | | '''20''' || dcm_done || SDRAM DCM cmd (inc/dec) done | ||
+ | |- | ||
+ | | '''21''' || dcm_locked || SDRAM DCM overflow | ||
+ | |- | ||
+ | | '''22''' || dcm_status[0] || SDRAM DCM overflow | ||
+ | |- | ||
+ | | '''24..23''' || sens_ph_err[1:0] || Sensor DCM phase error | ||
+ | |- | ||
+ | | '''25''' || sens_dcm_done || Sensor DCM cmd (inc/dec/reset) done | ||
+ | |- | ||
+ | | '''26''' || sens_dcm_locked || Sensor DCM overflow | ||
+ | |- | ||
+ | | '''27''' || sens_dcm_status[0] || Sensor DCM overflow | ||
+ | |- | ||
+ | | '''28''' || clockios_locked || dcm locked | ||
+ | |- | ||
+ | | '''29..30''' || clockios_status[1:0] || dcm status (bit 1 - dcm clkin stopped) | ||
+ | |- | ||
+ | | '''31''' || 1'b0 || 0x0 | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === Control register === | ||
+ | The dcr[31:0] bus is used to control the different blocks according to the control register values. The control register can be directly written by the CPU at the address 0x00. | ||
+ | |||
+ | |||
+ | ''333 control register'' | ||
+ | |||
+ | {|border="1" cellpadding="2" | ||
+ | ! bit # !! destination block !! Comments | ||
+ | |- | ||
+ | | '''0..2''' || Not used || | ||
+ | |- | ||
+ | | '''3''' || sensorpads || Inverts idclk phase | ||
+ | |- | ||
+ | | '''4''' || sensorpads || fillfactory sensor mode | ||
+ | |- | ||
+ | | '''5''' || sensorpads || delay hact pulse by 1 | ||
+ | |- | ||
+ | | '''6''' || sensorpads || ''cb_zoran'' | ||
+ | |- | ||
+ | | '''7''' || sensorpads || skip first scan line from the sensor | ||
+ | |- | ||
+ | | '''8''' || sensortrig || external trigger polarity (0: 1->0, 1: 0->1) | ||
+ | |- | ||
+ | | '''9''' || sensorpads || ''iarst'' | ||
+ | |- | ||
+ | | '''10''' || sensorpads || ''iaro'' | ||
+ | |- | ||
+ | | '''11''' || iobuf || EXPS (output pin) | ||
+ | |- | ||
+ | | '''12''' || iobuf || EXPS (output pin) | ||
+ | |- | ||
+ | | '''13''' || sensorpads || ''imrst'' | ||
+ | |- | ||
+ | | '''14''' || iobuf || XRST (output pin) | ||
+ | |- | ||
+ | | '''15''' || i2cpads || scl0 out | ||
+ | |- | ||
+ | | '''16''' || i2cpads || scl0 enable | ||
+ | |- | ||
+ | | '''17''' || i2cpads || sda0 out | ||
+ | |- | ||
+ | | '''18''' || i2cpads || sda0 enable | ||
+ | |- | ||
+ | | '''19''' || i2cpads || scl1 out | ||
+ | |- | ||
+ | | '''20''' || i2cpads || scl1 enable | ||
+ | |- | ||
+ | | '''21''' || i2cpads || sda1 out | ||
+ | |- | ||
+ | | '''22''' || i2cpads || sda1 enable | ||
+ | |- | ||
+ | | '''23''' || Not used || | ||
+ | |- | ||
+ | | '''24..27''' || clock_pclk || pclk source | ||
+ | |- | ||
+ | | '''28..30''' || Not used || | ||
+ | |- | ||
+ | | '''31''' || clock_pclk || clk enable | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | |||
+ | ''353 control register'' | ||
+ | |||
+ | {|border="1" cellpadding="2" | ||
+ | ! bit # !! destination block !! Comments | ||
+ | |- | ||
+ | | '''0''' || Not used || | ||
+ | |- | ||
+ | | '''1..2''' || compressor, sensorpix, histogram || | ||
+ | |- | ||
+ | | '''3''' || sensorpads || Inverts idclk phase | ||
+ | |- | ||
+ | | '''4''' || sensorpads || fillfactory sensor mode | ||
+ | |- | ||
+ | | '''5''' || sensorpads || delay hact pulse by 1 | ||
+ | |- | ||
+ | | '''6''' || sensorpads || ''cb_zoran'' | ||
+ | |- | ||
+ | | '''7''' || sensorpads || skip first scan line from the sensor | ||
+ | |- | ||
+ | | '''8''' || sensortrig || external trigger polarity (0: 1->0, 1: 0->1) | ||
+ | |- | ||
+ | | '''9''' || sensorpads || ''iarst'' | ||
+ | |- | ||
+ | | '''10''' || sensorpads || ''iaro'' | ||
+ | |- | ||
+ | | '''11''' || sensorpads || 0 - use 12-bit sensor data, 1 - use converter output pins | ||
+ | |- | ||
+ | | '''12''' || sensorpads || sensor trigger | ||
+ | |- | ||
+ | | '''13''' || sensorpads || ''imrst'' | ||
+ | |- | ||
+ | | '''14''' || iobuf || XRST (output pin) | ||
+ | |- | ||
+ | | '''15''' || i2cpads || scl0 out | ||
+ | |- | ||
+ | | '''16''' || i2cpads || scl0 enable | ||
+ | |- | ||
+ | | '''17''' || i2cpads || sda0 out | ||
+ | |- | ||
+ | | '''18''' || i2cpads || sda0 enable | ||
+ | |- | ||
+ | | '''19''' || sensorpads || dclkmode | ||
+ | |- | ||
+ | | '''20''' || sensorpads || use {vact,hact} as 2 LSB in 14-bit data | ||
+ | |- | ||
+ | | '''21..22''' || sensorpads || register hact, vact, bpf N/4 Tpclk later than data | ||
+ | |- | ||
+ | | '''23''' || Not used || | ||
+ | |- | ||
+ | | '''24..25''' || BUFGMUX || pclk source | ||
+ | |- | ||
+ | | '''28..30''' || compressor || | ||
+ | |- | ||
+ | | '''31''' || clock_pclk || | ||
+ | |- | ||
+ | |} | ||
=== Others === | === Others === | ||
* Looks like Theora compressor requires 90° phase clock that was abandoned in the 353 design. | * Looks like Theora compressor requires 90° phase clock that was abandoned in the 353 design. | ||
− | + | Using different phases reduces AC component of the current through the power/ground lines of the FPGA by spreading register transitions. Theora has larger core so it may help spreading phases.--[[User:Andrey.filippov|Andrey.filippov]] 13:45, 25 February 2008 (CST) | |
* ...? | * ...? | ||
Line 182: | Line 503: | ||
* ...? | * ...? | ||
+ | These lists of update are obviously incomplete. They need to be more detailed in order to make an exhaustive list of the changes that have to be done. | ||
+ | |||
+ | == 353 Theora new design == | ||
+ | === Compressor === | ||
+ | |||
+ | Writing tables in compressor (and mcontr8ch) is the same than the 333 design : | ||
+ | * ia = 0x2d and idi = table address (X313_WA_COMP_TA=0x2d) | ||
+ | then | ||
+ | * ia = 0x2c and idi = table data (X313_WA_COMP_TD=0x2c) | ||
+ | |||
+ | Example : Writing zerobin and quantization tables in 353 Theora design | ||
+ | |||
+ | [[Image:Writetabs.jpg]] | ||
+ | |||
+ | === Sensorpix === | ||
+ | |||
+ | Most of the 353 design was used for the new design. Writing procedure for gamma tables in sensorpix block is the same than in 353 (ie with ta bus and twr_gamma signal). | ||
+ | |||
+ | * ia = 0x0e and idi = table address | ||
+ | |||
+ | then | ||
+ | |||
+ | * ia = 0x0f and idi = table data | ||
+ | |||
+ | Table address is not autoincremented within the sensorpix block but is fed externally with the ta bus. | ||
+ | |||
+ | [[Image:Gammatab.jpg]] | ||
+ | |||
+ | === Memory controller === | ||
+ | |||
+ | {|border="1" cellpadding="2" | ||
+ | ! Channel !! Description | ||
+ | |- | ||
+ | | '''0''' || 8/16 bit data from sensor to SDRAM | ||
+ | |- | ||
+ | | '''1''' || 16 bit data from SDRAM to FPN correction module | ||
+ | |- | ||
+ | | '''2''' || 20x20 tiles of raw data from SDRAM to the color space converter and compressor | ||
+ | |- | ||
+ | | '''3''' || PIO read/write of SDRAM data | ||
+ | |- | ||
+ | | '''4''' || Writing current (restored) frame as YCbCr 4:2:0 data to SDRAM | ||
+ | |- | ||
+ | | '''5''' || Reading previous frame as YCbCr 4:2:0 data from SDRAM | ||
+ | |- | ||
+ | | '''6''' || Writing 12-bit pre-tokens to SDRAM (in macroblock-scan order, starting with AC[63] | ||
+ | |- | ||
+ | | '''7''' || Reading 12-bit pre-tokens from SDRAM in indexed coded order | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === System interface === | ||
+ | |||
+ | {|border="1" cellpadding="2" | ||
+ | ! Address !! da signal !! Comments | ||
+ | |- | ||
+ | | '''0x00''' || da_ctl || WE to control 32-bit register (1 loc) | ||
+ | |- | ||
+ | | '''0x01''' || da_dmamode || select writing to dma_cntr/dma_raw (1 loc) | ||
+ | |- | ||
+ | | '''0x02''' || da_sensormode || select writing to sensorpix (1 loc) | ||
+ | |- | ||
+ | | '''0x03''' || da_virttrig || write virtual trigger threshold | ||
+ | |- | ||
+ | | '''0x04''' || da_sensortrig || select writing to sensorpix (1 loc) | ||
+ | |- | ||
+ | | '''0x05''' || da_sensortrig_lines || write number of lines to be transferred in a frame (or after trigger) | ||
+ | |- | ||
+ | | '''0x07''' || da_sens_dc || write to sensor DCDC converter frequency divider | ||
+ | |- | ||
+ | | '''0x08''' || da_dcm || tune SDRAM clock phase | ||
+ | |- | ||
+ | | '''0x0a''' || da_framesync_dly || write frame sync interrupt delay (in scan lines) | ||
+ | |- | ||
+ | | '''0x0e''' || da_table_a0 || write gamma table address | ||
+ | |- | ||
+ | | '''0x0f''' || twr0 || write gamma table data | ||
+ | |- | ||
+ | | '''0x10''' || || Status register | ||
+ | |- | ||
+ | | '''0x1b''' || dcmrst || async signal to restart DCMs (if irnw=0) | ||
+ | |- | ||
+ | | '''0x1c..0x1f''' || da_interrupts || interrupt control | ||
+ | |- | ||
+ | | '''0x20..0x27''' || da_mcontr || select reading/writing to mcontr (8 locations) | ||
+ | |- | ||
+ | | '''0x28..0x2f''' || da_compressor || will be farther decoded in the compressor module | ||
+ | |- | ||
+ | | '''0x2c..0x2d''' || da_table || write gamma tables address (same as in compressor) | ||
+ | |- | ||
+ | | '''0x30''' || da_mem || read/write to SDRAM buffer, autoincrement address | ||
+ | |- | ||
+ | | '''0x40..0x43''' || da_hist || write/read histogram related data/registers | ||
+ | |- | ||
+ | | '''0x44..0x47''' || da_rtc || real time clock | ||
+ | |- | ||
+ | | '''0x48''' || da_timestamp || write timestamp mode | ||
+ | |- | ||
+ | | '''0x74''' || da_xjta0 || write to external (sensor board) JTAG | ||
+ | |- | ||
+ | | '''0x78..0x7b''' || da_extsync || control of external sync module 0x78 - 0x7b | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === Interrupts === | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! irq_in !! Signal !! Comments | ||
+ | |- | ||
+ | | '''15..8''' || GND || Extra | ||
+ | |- | ||
+ | | '''7''' || compressor_done_compress || single-cycle pulse when the compressed frame is sent out | ||
+ | |- | ||
+ | | '''6''' || compressor_reset_compress || reset compressor done interrupt (writing any compressor command) | ||
+ | |- | ||
+ | | '''5''' || GND || dcc_rdy was tied to GND in the 333 design | ||
+ | |- | ||
+ | | '''4''' || GND || eot irq was tied to GND in the 333 design | ||
+ | |- | ||
+ | | '''3''' || sr_sensortrig[2] || (sync to pclk) - level, reset by writing to sensor triggering command register | ||
+ | |- | ||
+ | | '''2''' || xfer_over_irq || (sync to pclk) - frame acquisition over | ||
+ | |- | ||
+ | | '''1''' || trig_irq || (sync to pclk) - external trigger | ||
+ | |- | ||
+ | | '''0''' || vacts || (sync to pclk) - frame sync | ||
+ | |- | ||
+ | |} | ||
+ | === DMA FIFOs === | ||
+ | A single DMA FIFO from the 333 design will be instanciated. | ||
− | + | === FPGA -> CPU data out MUX === | |
+ | |||
+ | {|border="1" cellpadding="2" | ||
+ | ! Address !! ia(6) !! ia(5) !! ia(4) !! ia(2) !! ia(0) !! iod[31:0] !! Comments | ||
+ | |- | ||
+ | | '''0x0..''' || '''0''' || '''0''' || '''0''' || '''x''' || '''0''' || dma_d[31:0] || DMA data | ||
+ | |- | ||
+ | | '''0x1..''' || '''0''' || '''0''' || '''1''' || '''x''' || '''x''' || rd_regs[31:0] || Data from internal registers | ||
+ | |- | ||
+ | | '''0x2..''' || '''0''' || '''1''' || '''0''' || '''x''' || '''x''' || {8'h0,xfer_bytes[23:0]} || Frame length (in bytes) | ||
+ | |- | ||
+ | | '''0x3..''' || '''0''' || '''0''' || '''1''' || '''x''' || '''x''' || bdo[31:0] || 32-bit data from SDRAM channel 3 | ||
+ | |- | ||
+ | | '''0x40..0x43''' || '''1''' || '''0''' || '''x''' || '''0''' || '''x''' || hist_do[31:0] || Histogram data out, actully only [17:0] | ||
+ | |- | ||
+ | | '''0x44''' || '''1''' || '''0''' || '''x''' || '''1''' || '''0''' || {12'h0,pio_usec[19:0]} || usec output from RTC | ||
+ | |- | ||
+ | | '''0x45''' || '''1''' || '''0''' || '''x''' || '''1''' || '''1''' || pio_sec[31:0] || sec output from RTC | ||
+ | |- | ||
+ | | '''0x6..''' || '''1''' || '''1''' || '''0''' || '''x''' || '''x''' || 32'h0 || 0x0000 | ||
+ | |- | ||
+ | | '''0x7..''' || '''1''' || '''1''' || '''1''' || '''x''' || '''x''' || {14'b0,xfpgatdo,xfpgastat,4'b0,io_pins[11:0]} || TDO read from an external FPGA / Multiplexed read data from xjtag / Status of 12 i/o pins | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === Internal registers MUX and status register === | ||
+ | |||
+ | {|border="1" cellpadding="2" | ||
+ | ! Address !! ia(1) !! ia(0) !! rd_regs[31:0] !! Comments | ||
+ | |- | ||
+ | | '''0x10''' || '''0''' || '''0''' || Status register || See below | ||
+ | |- | ||
+ | | '''0x11''' || '''0''' || '''1''' || irqr[31:0] || Interrupts | ||
+ | |- | ||
+ | | '''0x12''' || '''1''' || '''0''' || {5'b0,trig_v[10:0],4'b0,trig_h[11:0]} || Trigger phase | ||
+ | |- | ||
+ | | '''0x13''' || '''1''' || '''1''' || MODELREV || Model revision | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | '' Status register '' | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! Bit # !! Signal !! Comments | ||
+ | |- | ||
+ | | '''0''' || sr_sda0 || I2C data | ||
+ | |- | ||
+ | | '''1''' || sr_scl0 || I2C clock | ||
+ | |- | ||
+ | | '''2..10''' || rq_busy[8:0] || Request or busy - per mcontr channel | ||
+ | |- | ||
+ | | '''11''' || sr_memrdy || Ready to r/w next 8x32 page (channel 3) CPU<->SDRAM | ||
+ | |- | ||
+ | | '''12''' || sr_wrempty || CPU write buffer empty (valid only in write mode) | ||
+ | |- | ||
+ | | '''13..15''' || sr_sensortrig[2:0] || x00 - idle, x01 - waiting vacts to start, x10 - waiting for trigger, x11 - frame over ,1xx - frame done (reset by writing command to sensor_trig | ||
+ | |- | ||
+ | | '''16''' || dma_empty || dma output buffer empty and dma is enabled (pessimistic - with delay) | ||
+ | |- | ||
+ | | '''17..18''' || dcm_err[1:0] || 00 - no data (SDRAM reads) since last change (wclk*wcmd) | ||
+ | |||
+ | , 01 - clock is too late , 10 - clock is too early , 11 - OK (some measurements show too late, some - too early) | ||
+ | |- | ||
+ | | '''19''' || dcm_done || SDRAM DCM cmd (inc/dec) done | ||
+ | |- | ||
+ | | '''20''' || dcm_locked || SDRAM DCM overflow | ||
+ | |- | ||
+ | | '''21..22''' || sens_ph_err[1:0] || Sensor DCM phase error | ||
+ | |- | ||
+ | | '''23''' || sens_dcm_done || Sensor DCM cmd (inc/dec/reset) done | ||
+ | |- | ||
+ | | '''24''' || sens_dcm_locked || Sensor DCM overflow | ||
+ | |- | ||
+ | | '''25''' || clockios_locked || dcm locked | ||
+ | |- | ||
+ | | '''26''' || clockios_status[1] || dcm status (bit 1 - dcm clkin stopped) | ||
+ | |- | ||
+ | | '''27''' || sr_pipe_rdy || Will go active with delay to overlap with DMA busy (external) | ||
+ | |- | ||
+ | | '''28''' || sr_pipe_nempty || Compressor pipe not empty (updated with done -> IRQ) | ||
+ | |- | ||
+ | | '''29''' || sr_pipe_full || Compressor pipe has 3 frame compress commands in the input queue/in progress | ||
+ | |- | ||
+ | | '''30''' || en_refresh || Status bit to find out if SDRAM is programmed | ||
+ | |- | ||
+ | | '''31''' || took_frame_num_wr || Odd/even frame of tokens written | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === Control register === | ||
+ | {|border="1" cellpadding="2" | ||
+ | ! bit # !! Signal || Destination block !! Comments | ||
+ | |- | ||
+ | | '''0''' || || Not used || | ||
+ | |- | ||
+ | | '''1..2''' || cb_bayer_phase || compressor, sensorpix, histogram || | ||
+ | |- | ||
+ | | '''3''' || || sensorpads || Inverts idclk phase (Not used) | ||
+ | |- | ||
+ | | '''4''' || cb_fillfactory || sensorpads || fillfactory sensor mode | ||
+ | |- | ||
+ | | '''5''' || cb_dlyhact || sensorpads || delay hact pulse by 1 | ||
+ | |- | ||
+ | | '''6''' || cb_zoran || sensorpads || ''cb_zoran'' | ||
+ | |- | ||
+ | | '''7''' || cb_skipline || sensorpads || skip first scan line from the sensor | ||
+ | |- | ||
+ | | '''8''' || cb_xt_pol || sensortrig || external trigger polarity (0: 1->0, 1: 0->1) | ||
+ | |- | ||
+ | | '''9''' || iarst || sensorpads || ''iarst'' | ||
+ | |- | ||
+ | | '''10''' || iaro || sensorpads || ''iaro'' | ||
+ | |- | ||
+ | | '''11''' || cb_encnvclk || sensorpads || 0 - use 12-bit sensor data, 1 - use converter output pins | ||
+ | |- | ||
+ | | '''12''' || cb_sensor_trigger || sensorpads || sensor trigger | ||
+ | |- | ||
+ | | '''13''' || imrst || sensorpads || ''imrst'' | ||
+ | |- | ||
+ | | '''14''' || cb_scl0_o || iobuf || XRST (output pin) | ||
+ | |- | ||
+ | | '''15''' || cb_scl0_o || i2cpads || scl0 out | ||
+ | |- | ||
+ | | '''16''' || cb_scl0_en || i2cpads || scl0 enable | ||
+ | |- | ||
+ | | '''17''' || cb_sda0_o || i2cpads || sda0 out | ||
+ | |- | ||
+ | | '''18''' || cb_sda0_en || i2cpads || sda0 enable | ||
+ | |- | ||
+ | | '''19''' || cb_dclkmode || sensorpads || dclkmode | ||
+ | |- | ||
+ | | '''20''' || cb_pxd14 || sensorpads || use {vact,hact} as 2 LSB in 14-bit data | ||
+ | |- | ||
+ | | '''21..22''' || cb_latehact || sensorpads || register hact, vact, bpf N/4 Tpclk later than data | ||
+ | |- | ||
+ | | '''23''' || || Not used || | ||
+ | |- | ||
+ | | '''24..25''' || cb_pclksrc || BUFGMUX || pclk source | ||
+ | |- | ||
+ | | '''28..30''' || || Not used || | ||
+ | |- | ||
+ | | '''31''' || || Not used || | ||
+ | |- | ||
+ | |} | ||
+ | |||
+ | === Others === | ||
== See also == | == See also == | ||
+ | *[http://elphel.cvs.sourceforge.net/elphel/fpga/theora_353/ 353 Theora CVS] | ||
*[[Theora]] | *[[Theora]] | ||
*[[FPGA_Development_in_Elphel_cameras|FPGA Development in Elphel cameras]] | *[[FPGA_Development_in_Elphel_cameras|FPGA Development in Elphel cameras]] | ||
*[[Design Ideas|FPGA Theora Encoder for Videoconferencing]] | *[[Design Ideas|FPGA Theora Encoder for Videoconferencing]] | ||
*[[10353]] | *[[10353]] |
Latest revision as of 07:16, 16 April 2008
Elphel model 333 cameras were able to encode and stream Ogg Theora with 6.3.9 firmware. However, this model is no longer produced by Elphel. The goal of this project is to use the full potential of 353 cameras (larger FPGA, faster CPU) in order to port the Ogg Theora feature on the new hardware. First, the camera should be able to upload small Theora clips via FTP.
Different solutions are possible as previously mentioned in the Theora page :
- Instantiate both the Theora compressor and the MJPEG compressor in the FPGA since the new Spartan 3E seems to be large enough to handle the two features.
- Replace the existing MJPEG compressor with the Theora compressor and implement software Theora to JPEG conversion if JPEG is needed.
- Replace the existing MJPEG compressor in the 353 camera with the Theora compressor and keep two configuration files on the camera filesystem (one for Theora the other for MJPEG). FPGA code could be changed at run-time according to the needs.
Dealing with the last solution seems to be a good start for this project as the other features mentioned can be added later. In all cases, both FPGA code and software code will need to be adapted.
The source code of this project is available at http://elphel.cvs.sourceforge.net/elphel/fpga/theora_353/
Hardware updates
Compressor
Replace the MJPEG compressor in the 353 with the 333 Theora compressor (333 Theora FPGA code). Maybe some adaptations need to be done within the Theora compressor itself. However, assuming that the compressor worked in 333 cameras a simple instantiation should suffice.
Memory controller
Replace the 4-channel memory controller with an 8 channel memory interface as in the 333 model in order to handle Theora specific data.
Channel | 333 Theora | 353 |
---|---|---|
0 | 8/16 bit data from sensor to SDRAM | Data from the sensor (it can be combined with FPN correction data) to the SDRAM in either 8-bit mode or 16-bit |
1 | 16 bit data from SDRAM to FPN correction module | Reads FPN data from SDRAM (8bit - subtract, 8 bit - scale) and feeds it to FPGA for FPN correction of the data on the way from sensor to SDRAM (through channel 0) |
2 | 20x20 tiles of raw data from SDRAM to the color space converter and compressor | Provides data to JPEG encoder in 16x16x8bit MCUs. It can also provide data directly to CPU through DMA bypassing any compression |
3 | PIO read/write of SDRAM data | Provides bidirectional access from CPU through 8x32 bit window. |
4 | Writing current (restored) frame as YCbCr 4:2:0 data to SDRAM | |
5 | Reading previous frame as YCbCr 4:2:0 data from SDRAM | |
6 | Writing 12-bit pre-tokens to SDRAM (in macroblock-scan order, starting with AC[63] | |
7 | reading 12-bit pre-tokens from SDRAM in indexed coded order |
Sensor interface
sensorpix block must be adapted in order to provide a coherent interface between the memory controller and the sensor (channels 0 and 1)
System Interface
Adapt the system interface to assure communication between FPGA and its environment.
A feature of the system interface is to establish communication between the system CPU and the different blocks within the FPGA (compressor, memory controller etc). This is done by selecting a block with the address bus a[12:0] connected to the internal address bus ial[7:0]:
x353.v always @ (posedge cwr) begin a0[7:0]<=ial[7:0]; // may want to change to just ia if ia will be late enough; wnr0 <= ~irnw; da_ctl0 <= (ial[7:0]==8'h00); // 0x00 WE to control 32-bit register (1 loc) da_dmamode0 <= (ial[7:0]==8'h01); // 0x01 select writing to dma_cntr/dma_raw (1 loc) da_sensormode0 <= (ial[7:0]==8'h02); // 0x02 select writing to sensorpix (1 loc) ... da_compressor0 <= (ial[7:1]==7'h06); // 0x0c..0x0d - will be farther decoded in the compressor module ...
Since memory controller and compressor are to be replaced these addresses have to be adapted.
353 system interface address table
Address | da signal | Comments |
---|---|---|
0x00 | da_ctl0 | WE to control 32-bit register (1 loc) |
0x01 | da_dmamode0 | select writing to dma_cntr/dma_raw (1 loc) |
0x02 | da_sensormode0 | select writing to sensorpix (1 loc) |
0x03 | da_virttrig0 | write virtual trigger threshold |
0x04 | da_sensortrig0 | select writing to sensorpix (1 loc) |
0x05 | da_sensortrig_lines0 | write number of lines to be transferred in a frame (or after trigger) |
0x07 | da_sens_dc0 | write to sensor DCDC converter frequency divider |
0x08 | da_dcm0 | tune SDRAM clock phase |
0x09 | da_saturation0 | write color saturation values |
0x0a | da_framesync_dly0 | write frame sync interrupt delay (in scan lines) |
0x0c..0x0d | da_compressor0 | will be farther decoded in the compressor module |
0x0e | da_table_a0 | write tables address |
0x0f | twr0 | write tables data |
0x10 | Status register | |
0x1b | dcmrst | async signal to restart DCMs (if irnw=0) |
0x1c..0x1f | da_interrupts0 | interrupt control |
0x20..0x2f | da_dswe0 | select reading/writing to mcontr (16 locations) |
0x30 | da_mem0 | read/write to SDRAM buffer, autoincrement address |
0x40..0x43 | da_hist0 | write/read histogram related data/registers |
0x44..0x47 | da_rtc0 | real time clock |
0x48 | da_timestamp0 | write timestamp mode |
0x74 | da_xjtag0 | write to external (sensor board) JTAG |
0x78..0x7b | da_extsync0 | control of external sync module 0x78 - 0x7b |
333 system interface address table
Address | da signal | Comments |
---|---|---|
0x00 | da_ctl0 | WE to control 32-bit register (1 loc) |
0x01 | da_dmamode0 | select writing to dma_cntr/dma_raw (1 loc) |
0x02 | da_sensormode0 | select writing to sensorpix (1 loc) |
0x03 | da_virttrig0 | write virtual trigger threshold |
0x04 | da_sensortrig0 | select writing to sensorpix (1 loc) |
0x05 | da_sensortrig_lines0 | write number of lines to be transferred in a frame (or aftre trigger) |
0x06 | da_interrupts0 | interrupt mask |
0x07 | da_sens_dc0 | write to sensor DCDC converter frequency divider |
0x08 | da_dcm0 | tune SDRAM clock phase |
0x10 | da_debug | write 0x10 any - load debug shift, read (through cs4) -shift |
0x20..0x27 | da_mcontr0 | select reading/writing to mcontr (8 locations) |
0x28..0x2f | da_compressor0 | will be farther decoded in the compressor module |
0x2c..0x2d | da_table0 | write gamma tables address (same as in compressor) |
0x30 | da_mem0 | read/write to SDRAM buffer, autoincrement address |
Addresses 0x01,2,3,4,5,6,8 and 0x30 can be kept in the 353 system interface. The interrupt mask address 0x06 in the 333 sys interface is no longer used (353 uses interrupt vectors). The Theora compressor and the new memory controller addresses have to be mapped again in the new design (addresses 0x0c..0x0d and 0x20 to 0x2f in the 353 sys interface).
Interrupts
Adapt the Theora compressor interrupts to the 353 interrupt vector .
The 353 interrupt vector can handle up to 16 different irq. However, only irq 0 to 7 are used :
x353.v assign irq_in= {8'b0, // extra compressor_done_compress, // 7 - will go high after all data is sent out (reset by compressor) compressor_done_input, // 6 - will go high after EOT and persist until DCT is enabled (reset by compressor) dcc_rdy, // 5 - obsolete in 333 - channel3 has 128 more dc coefficients (or some if the compression is finished) compressor_eot, // 4 - compressor read in the last MCU (predictable time to end of transfer) sr_sensortrig[2], // 3 - (sync to pclk) - level, reset by writing to sensor triggering command register xfer_over_irq, // 2 - (sync to pclk) - frame acquisition over trig_irq, // 1 - (sync to pclk) - external trigger vacts}; // 0 - (sync to pclk) - frame sync
353 MJPEG compressor triggers irqs 4, 6 and 7. 333 Theora compressor is the source of two irqs :
compressor_all.v done, // single-cycle pulse when the compressed frame is sent out (IRQ source). reset_compress, // reset compressor done interrupt (writing any compressor command)
Adaptation should consist of assigning Theora compressor irq sources to vectors 6 and 7 for example if the MJPEG compressor is to be replaced.
DMA FIFOs
353 design uses 2 DMA FIFOs between the compressor and the system interface instead of one for the 333 Theora compressor. The two DMA FIFOs have also slight differences between the two design. Maybe a single 333 FIFO should be kept for the final design (?)
FPGA -> CPU data out MUX
The purpose of this MUX is to route data out from the different FPGA blocks to the system interface and then to the data bus to the CPU. The selection is made with the internal address bus ia.
_ --| \ --| | --| | --| |--- iod[31:0] -> to system interface --| | --| | |_/ from system interface -> ia[7:0]__|
333 MUX
Adress range | ia(5) | ia(4) | iod[31:0] | Comments |
---|---|---|---|---|
0x0.. | 0 | 0 | dma_d[31:0] | DMA data |
0x1.. | 0 | 1 | rd_regs[31:0] | Data from internal registers |
0x2.. | 1 | 0 | {8'h0,xfer_bytes[23:0]} | Frame length (in bytes) |
0x3.. | 1 | 1 | bdo[31:0] | 32-bit data from SDRAM channel 3 |
353 MUX
Address | ia(6) | ia(5) | ia(4) | ia(2) | ia(0) | iod[31:0] | Comments |
---|---|---|---|---|---|---|---|
0x0.. (even) | 0 | 0 | 0 | X | 0 | dma_d0[31:0] | DMA 0 data |
0x0.. (odd) | 0 | 0 | 0 | X | 1 | dma_d1[31:0] | DMA 1 data |
0x1.. | 0 | 0 | 1 | X | X | rd_regs[31:0] | Data from internal registers |
0x2.. | 0 | 1 | 0 | X | X | dsdo[31:0] | Data out from descriptor memory |
0x3.. | 0 | 1 | 1 | X | X | bdo[31:0] | 32-bit data from SDRAM channel3 |
0x40..0x43 | 1 | 0 | X | 0 | X | hist_do[31:0] | Histogram data out, actully only [17:0] |
0x44 | 1 | 0 | X | 1 | 0 | {12'h0,pio_usec[19:0]} | usec output from RTC |
0x45 | 1 | 0 | X | 1 | 1 | pio_sec[31:0] | sec output from RTC |
0x6.. | 1 | 1 | 0 | X | X | 32'h0 | 0x0000 |
0x7.. | 1 | 1 | 1 | X | X | {14'b0,xfpgatdo,xfpgastat,4'b0,io_pins[11:0]} | TDO read from an external FPGA / Multiplexed read data from xjtag / Status of 12 i/o pins |
Internal registers MUX and status register
333 MUX
Address | ia(1) | ia(0) | rd_regs[31:0] | Comments |
---|---|---|---|---|
0x10 | 0 | 0 | Status register | See below |
0x11 | 0 | 1 | {24'b0,irqr[7:0]} | Interrupts |
0x12 | 1 | 0 | {5'b0,trig_v[10:0],4'b0,trig_h[11:0]} | Trigger phase |
0x13 | 1 | 1 | MODELREV | Model revision |
353 MUX
Address | ia(2) | ia(1) | ia(0) | rd_regs[31:0] | Comments |
---|---|---|---|---|---|
0x10 | 0 | 0 | 0 | Status register | See below |
0x11 | 0 | 0 | 1 | irqr[31:0] | Interrupts |
0x12 | 0 | 1 | 0 | {5'b0,trig_v[10:0],4'b0,trig_h[11:0]} | Trigger phase |
0x13 | 0 | 1 | 1 | MODELREV | Model revision |
0x14 | 1 | X | 0 | {8'h0,imgptr[23:0]} | Image pointer in 32-byte chunks |
0x15 | 1 | X | 1 | hifreq[31:0] | Accumulated high-freq components |
333 status register
Bit # | Signal | Comments |
---|---|---|
0 | sr_sda0 | I2C to sensor |
1 | sr_scl0 | I2C clock0 |
2 | sr_sda1 | I2C |
3 | sr_scl1 | I2C clock1 |
4..12 | rq_busy[8:0] | Request or busy - per mcontr channel |
13..15 | sr_sensortrig[2:0] | x00 - idle, x01 - waiting vacts to start, x10 - waiting for trigger, x11 - frame over ,1xx - frame done (reset by writing command to sensor_trig |
16 | sr_memrdy | Ready to r/w next 8x32 page (channel 3) CPU<->SDRAM |
17 | sr_wrempty | CPU write buffer empty (valid only in write mode) |
18 | 1'b0 | 0x0 |
19 | dma_empty | dma output buffer empty and dma is enabled (pessimistic - with delay) |
20 | itrig | TRIG input |
21..22 | dcm_err[1:0] | 00 - no data (SDRAM reads) since last change (wclk*wcmd)
, 01 - clock is too late , 10 - clock is too early , 11 - OK (some measurements show too late, some - too early) |
23 | dcm_done | |
24 | sr_pipe_rdy | Will go active with delay to overlap with DMA busy (external) |
25 | sr_pipe_nempty | Compressor pipe not empty (updated with done -> IRQ) |
26 | sr_pipe_full | Compressor pipe has 3 frame compress commands in the input queue/in progress |
27 | en_refresh | Status bit to find out if SDRAM is programmed |
28 | tok_frame_num_wr | Odd/even frame of tokens written |
29 | 1'b0 | 0x0 |
30 | debug_out | Debug shift register output |
31 | 'b0 | 0x0 |
353 status register
Bit # | Signal | Comments |
---|---|---|
0 | sr_sda0 | I2C to sensor |
1 | sr_scl0 | I2C clock |
2 | sr_ch0rdy | Ready to write next page (channel 0) SENSOR->SDRAM |
3 | sr_ch1rdy | Ready to read next page (channel 1) SDRAM->FPN(SENSOR) |
4 | sr_ch2rdy | Ready to read next page (channel 2) SDRAM->DMA |
5 | sr_memrdy | Ready to r/w next 8x32 page (channel 3) CPU<->SDRAM |
6 | sr_wrempty | CPU write buffer empty (valid only in write mode). May reprogram channel3. |
7..10 | sr_nextFrame[3:0] | (level) generated before actual block is filled - needed to be combined with the pulse from buffer control |
11..13 | sr_sensortrig[2:0] | x00 - idle, x01 - waiting vacts to start, x10 - waiting for trigger, x11 - frame over ,1xx - frame done (reset by writing command to sensor_trig |
14 | dcc_rdy | 128 of DC components from JPEG encoder are available (same as interrupt) |
15 | compressor_done_input | will go high after EOT and persist until DCT is enabled |
16 | compressor_done_compress | will go high after all data is sent out |
17 | dma_empty | dma output buffer empty and dma is enabled (pessimistic - with delay) |
19..18 | dcm_err[1:0] | SDRAM DCM phase error |
20 | dcm_done | SDRAM DCM cmd (inc/dec) done |
21 | dcm_locked | SDRAM DCM overflow |
22 | dcm_status[0] | SDRAM DCM overflow |
24..23 | sens_ph_err[1:0] | Sensor DCM phase error |
25 | sens_dcm_done | Sensor DCM cmd (inc/dec/reset) done |
26 | sens_dcm_locked | Sensor DCM overflow |
27 | sens_dcm_status[0] | Sensor DCM overflow |
28 | clockios_locked | dcm locked |
29..30 | clockios_status[1:0] | dcm status (bit 1 - dcm clkin stopped) |
31 | 1'b0 | 0x0 |
Control register
The dcr[31:0] bus is used to control the different blocks according to the control register values. The control register can be directly written by the CPU at the address 0x00.
333 control register
bit # | destination block | Comments |
---|---|---|
0..2 | Not used | |
3 | sensorpads | Inverts idclk phase |
4 | sensorpads | fillfactory sensor mode |
5 | sensorpads | delay hact pulse by 1 |
6 | sensorpads | cb_zoran |
7 | sensorpads | skip first scan line from the sensor |
8 | sensortrig | external trigger polarity (0: 1->0, 1: 0->1) |
9 | sensorpads | iarst |
10 | sensorpads | iaro |
11 | iobuf | EXPS (output pin) |
12 | iobuf | EXPS (output pin) |
13 | sensorpads | imrst |
14 | iobuf | XRST (output pin) |
15 | i2cpads | scl0 out |
16 | i2cpads | scl0 enable |
17 | i2cpads | sda0 out |
18 | i2cpads | sda0 enable |
19 | i2cpads | scl1 out |
20 | i2cpads | scl1 enable |
21 | i2cpads | sda1 out |
22 | i2cpads | sda1 enable |
23 | Not used | |
24..27 | clock_pclk | pclk source |
28..30 | Not used | |
31 | clock_pclk | clk enable |
353 control register
bit # | destination block | Comments |
---|---|---|
0 | Not used | |
1..2 | compressor, sensorpix, histogram | |
3 | sensorpads | Inverts idclk phase |
4 | sensorpads | fillfactory sensor mode |
5 | sensorpads | delay hact pulse by 1 |
6 | sensorpads | cb_zoran |
7 | sensorpads | skip first scan line from the sensor |
8 | sensortrig | external trigger polarity (0: 1->0, 1: 0->1) |
9 | sensorpads | iarst |
10 | sensorpads | iaro |
11 | sensorpads | 0 - use 12-bit sensor data, 1 - use converter output pins |
12 | sensorpads | sensor trigger |
13 | sensorpads | imrst |
14 | iobuf | XRST (output pin) |
15 | i2cpads | scl0 out |
16 | i2cpads | scl0 enable |
17 | i2cpads | sda0 out |
18 | i2cpads | sda0 enable |
19 | sensorpads | dclkmode |
20 | sensorpads | use {vact,hact} as 2 LSB in 14-bit data |
21..22 | sensorpads | register hact, vact, bpf N/4 Tpclk later than data |
23 | Not used | |
24..25 | BUFGMUX | pclk source |
28..30 | compressor | |
31 | clock_pclk |
Others
- Looks like Theora compressor requires 90° phase clock that was abandoned in the 353 design.
Using different phases reduces AC component of the current through the power/ground lines of the FPGA by spreading register transitions. Theora has larger core so it may help spreading phases.--Andrey.filippov 13:45, 25 February 2008 (CST)
- ...?
Software updates
- Adapt FPGA definitions (x353.h) and most likely some other FPGA drivers.
- ...?
These lists of update are obviously incomplete. They need to be more detailed in order to make an exhaustive list of the changes that have to be done.
353 Theora new design
Compressor
Writing tables in compressor (and mcontr8ch) is the same than the 333 design :
- ia = 0x2d and idi = table address (X313_WA_COMP_TA=0x2d)
then
- ia = 0x2c and idi = table data (X313_WA_COMP_TD=0x2c)
Example : Writing zerobin and quantization tables in 353 Theora design
Sensorpix
Most of the 353 design was used for the new design. Writing procedure for gamma tables in sensorpix block is the same than in 353 (ie with ta bus and twr_gamma signal).
- ia = 0x0e and idi = table address
then
- ia = 0x0f and idi = table data
Table address is not autoincremented within the sensorpix block but is fed externally with the ta bus.
Memory controller
Channel | Description |
---|---|
0 | 8/16 bit data from sensor to SDRAM |
1 | 16 bit data from SDRAM to FPN correction module |
2 | 20x20 tiles of raw data from SDRAM to the color space converter and compressor |
3 | PIO read/write of SDRAM data |
4 | Writing current (restored) frame as YCbCr 4:2:0 data to SDRAM |
5 | Reading previous frame as YCbCr 4:2:0 data from SDRAM |
6 | Writing 12-bit pre-tokens to SDRAM (in macroblock-scan order, starting with AC[63] |
7 | Reading 12-bit pre-tokens from SDRAM in indexed coded order |
System interface
Address | da signal | Comments |
---|---|---|
0x00 | da_ctl | WE to control 32-bit register (1 loc) |
0x01 | da_dmamode | select writing to dma_cntr/dma_raw (1 loc) |
0x02 | da_sensormode | select writing to sensorpix (1 loc) |
0x03 | da_virttrig | write virtual trigger threshold |
0x04 | da_sensortrig | select writing to sensorpix (1 loc) |
0x05 | da_sensortrig_lines | write number of lines to be transferred in a frame (or after trigger) |
0x07 | da_sens_dc | write to sensor DCDC converter frequency divider |
0x08 | da_dcm | tune SDRAM clock phase |
0x0a | da_framesync_dly | write frame sync interrupt delay (in scan lines) |
0x0e | da_table_a0 | write gamma table address |
0x0f | twr0 | write gamma table data |
0x10 | Status register | |
0x1b | dcmrst | async signal to restart DCMs (if irnw=0) |
0x1c..0x1f | da_interrupts | interrupt control |
0x20..0x27 | da_mcontr | select reading/writing to mcontr (8 locations) |
0x28..0x2f | da_compressor | will be farther decoded in the compressor module |
0x2c..0x2d | da_table | write gamma tables address (same as in compressor) |
0x30 | da_mem | read/write to SDRAM buffer, autoincrement address |
0x40..0x43 | da_hist | write/read histogram related data/registers |
0x44..0x47 | da_rtc | real time clock |
0x48 | da_timestamp | write timestamp mode |
0x74 | da_xjta0 | write to external (sensor board) JTAG |
0x78..0x7b | da_extsync | control of external sync module 0x78 - 0x7b |
Interrupts
irq_in | Signal | Comments |
---|---|---|
15..8 | GND | Extra |
7 | compressor_done_compress | single-cycle pulse when the compressed frame is sent out |
6 | compressor_reset_compress | reset compressor done interrupt (writing any compressor command) |
5 | GND | dcc_rdy was tied to GND in the 333 design |
4 | GND | eot irq was tied to GND in the 333 design |
3 | sr_sensortrig[2] | (sync to pclk) - level, reset by writing to sensor triggering command register |
2 | xfer_over_irq | (sync to pclk) - frame acquisition over |
1 | trig_irq | (sync to pclk) - external trigger |
0 | vacts | (sync to pclk) - frame sync |
DMA FIFOs
A single DMA FIFO from the 333 design will be instanciated.
FPGA -> CPU data out MUX
Address | ia(6) | ia(5) | ia(4) | ia(2) | ia(0) | iod[31:0] | Comments |
---|---|---|---|---|---|---|---|
0x0.. | 0 | 0 | 0 | x | 0 | dma_d[31:0] | DMA data |
0x1.. | 0 | 0 | 1 | x | x | rd_regs[31:0] | Data from internal registers |
0x2.. | 0 | 1 | 0 | x | x | {8'h0,xfer_bytes[23:0]} | Frame length (in bytes) |
0x3.. | 0 | 0 | 1 | x | x | bdo[31:0] | 32-bit data from SDRAM channel 3 |
0x40..0x43 | 1 | 0 | x | 0 | x | hist_do[31:0] | Histogram data out, actully only [17:0] |
0x44 | 1 | 0 | x | 1 | 0 | {12'h0,pio_usec[19:0]} | usec output from RTC |
0x45 | 1 | 0 | x | 1 | 1 | pio_sec[31:0] | sec output from RTC |
0x6.. | 1 | 1 | 0 | x | x | 32'h0 | 0x0000 |
0x7.. | 1 | 1 | 1 | x | x | {14'b0,xfpgatdo,xfpgastat,4'b0,io_pins[11:0]} | TDO read from an external FPGA / Multiplexed read data from xjtag / Status of 12 i/o pins |
Internal registers MUX and status register
Address | ia(1) | ia(0) | rd_regs[31:0] | Comments |
---|---|---|---|---|
0x10 | 0 | 0 | Status register | See below |
0x11 | 0 | 1 | irqr[31:0] | Interrupts |
0x12 | 1 | 0 | {5'b0,trig_v[10:0],4'b0,trig_h[11:0]} | Trigger phase |
0x13 | 1 | 1 | MODELREV | Model revision |
Status register
Bit # | Signal | Comments |
---|---|---|
0 | sr_sda0 | I2C data |
1 | sr_scl0 | I2C clock |
2..10 | rq_busy[8:0] | Request or busy - per mcontr channel |
11 | sr_memrdy | Ready to r/w next 8x32 page (channel 3) CPU<->SDRAM |
12 | sr_wrempty | CPU write buffer empty (valid only in write mode) |
13..15 | sr_sensortrig[2:0] | x00 - idle, x01 - waiting vacts to start, x10 - waiting for trigger, x11 - frame over ,1xx - frame done (reset by writing command to sensor_trig |
16 | dma_empty | dma output buffer empty and dma is enabled (pessimistic - with delay) |
17..18 | dcm_err[1:0] | 00 - no data (SDRAM reads) since last change (wclk*wcmd)
, 01 - clock is too late , 10 - clock is too early , 11 - OK (some measurements show too late, some - too early) |
19 | dcm_done | SDRAM DCM cmd (inc/dec) done |
20 | dcm_locked | SDRAM DCM overflow |
21..22 | sens_ph_err[1:0] | Sensor DCM phase error |
23 | sens_dcm_done | Sensor DCM cmd (inc/dec/reset) done |
24 | sens_dcm_locked | Sensor DCM overflow |
25 | clockios_locked | dcm locked |
26 | clockios_status[1] | dcm status (bit 1 - dcm clkin stopped) |
27 | sr_pipe_rdy | Will go active with delay to overlap with DMA busy (external) |
28 | sr_pipe_nempty | Compressor pipe not empty (updated with done -> IRQ) |
29 | sr_pipe_full | Compressor pipe has 3 frame compress commands in the input queue/in progress |
30 | en_refresh | Status bit to find out if SDRAM is programmed |
31 | took_frame_num_wr | Odd/even frame of tokens written |
Control register
bit # | Signal | Destination block | Comments |
---|---|---|---|
0 | Not used | ||
1..2 | cb_bayer_phase | compressor, sensorpix, histogram | |
3 | sensorpads | Inverts idclk phase (Not used) | |
4 | cb_fillfactory | sensorpads | fillfactory sensor mode |
5 | cb_dlyhact | sensorpads | delay hact pulse by 1 |
6 | cb_zoran | sensorpads | cb_zoran |
7 | cb_skipline | sensorpads | skip first scan line from the sensor |
8 | cb_xt_pol | sensortrig | external trigger polarity (0: 1->0, 1: 0->1) |
9 | iarst | sensorpads | iarst |
10 | iaro | sensorpads | iaro |
11 | cb_encnvclk | sensorpads | 0 - use 12-bit sensor data, 1 - use converter output pins |
12 | cb_sensor_trigger | sensorpads | sensor trigger |
13 | imrst | sensorpads | imrst |
14 | cb_scl0_o | iobuf | XRST (output pin) |
15 | cb_scl0_o | i2cpads | scl0 out |
16 | cb_scl0_en | i2cpads | scl0 enable |
17 | cb_sda0_o | i2cpads | sda0 out |
18 | cb_sda0_en | i2cpads | sda0 enable |
19 | cb_dclkmode | sensorpads | dclkmode |
20 | cb_pxd14 | sensorpads | use {vact,hact} as 2 LSB in 14-bit data |
21..22 | cb_latehact | sensorpads | register hact, vact, bpf N/4 Tpclk later than data |
23 | Not used | ||
24..25 | cb_pclksrc | BUFGMUX | pclk source |
28..30 | Not used | ||
31 | Not used |