Difference between revisions of "Focus adjustment 393"
From ElphelWiki
(Created page with "==Description== internal use ==regular SFE== {| |thumb|1600px |} * '''restore''' from ''test_focusing/default.conf-xml'' * ''...") |
(→Pattern) |
||
| (23 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
==Description== | ==Description== | ||
internal use | internal use | ||
| − | == | + | ==Regular SFE== |
{| | {| | ||
|[[File:Aberration calibration 393 regular SFE.png|thumb|1600px]] | |[[File:Aberration calibration 393 regular SFE.png|thumb|1600px]] | ||
|} | |} | ||
| − | + | # used on big the Xeon PC - 192.168.0.6 | |
| − | + | # '''restore''' from ''/home/elphel/test_focusing/default.conf-xml'' | |
| − | + | # '''quick get&show''' | |
| − | + | # '''find grid''' (if error - increase/decrease exposure using the 'camera settings' button - the range is 2.5-5.0 ms - rerun steps 3. and 4.) | |
| + | # '''no-move measure''' | ||
| + | # '''show PSF''' | ||
| + | # adjust screws | ||
| + | # repeat from 5. until good (if some PSF spots are missing - repeat from 4.) | ||
| + | |||
| + | ==Setup before using ImageJ Aberration Calibration plugin== | ||
| + | ===Parts=== | ||
| + | * Assembled SFE without lens and without IR-cut filter (can be with the filter if the target lens is different) | ||
| + | * M12 adapter | ||
| + | * 2 spacers: 5mm and 4.7mm (shaved off 0.3mm (made from 5mm spacer) for optimal adjustment) | ||
| + | * Lens N125B04530W with IR-cut filter. If the target lens is different, still use this one for adjustment then replace. Wrap the thread of the lens with the teflon tape for better thread fitting - 2 layers is enough. When screwing in make sure the tape does not get in the optical path. Screw in the lens until full stop. | ||
| + | {| | ||
| + | |valign='top'|[[File:SFE focusing parts.jpeg|thumb|500px|Fig.2a SFE parts]] | ||
| + | |valign='top'|[[File:SFE focusing sensor spacer.jpeg|thumb|150px|Fig.2b Sensor teflon spacers]] | ||
| + | |} | ||
| + | * Focus adjustment screws - do not overtighten initially. Later, right before starting the procedure when the camera is against the pattern - turn it on, while in jpeg open the control interface and adjust the screws for the best manual focus (do not apply too much force). | ||
| + | {| | ||
| + | |[[File:SFE focusing SFE screws.jpeg|thumb|200px|Fig.3 Focus adjustment screws]] | ||
| + | |} | ||
| + | |||
| + | ===Assembled setup=== | ||
| + | * Take a longer cable - at least 100mm | ||
| + | * Connect to port 0 | ||
| + | * Set the camera address to 192.168.0.38 | ||
| + | # temporary (ssh will freeze, connect from another window) | ||
| + | ~# ifconfig eth0 192.168.0.38 | ||
| + | |||
| + | # permanently (reboot required) | ||
| + | edit /etc/network/interfaces | ||
| + | |||
| + | * Make sure the power supply provides the right voltage - 12V or 48V. If possible install PoE compatible power board - 10386. | ||
| + | {| | ||
| + | |[[File:SFE focusing camera.jpeg|thumb|200px|Fig.4 Assembled focusing setup]] | ||
| + | |} | ||
| + | |||
| + | ===Pattern=== | ||
| + | * Use the wallpaper pattern. | ||
| + | * Notice the distance from the pattern. | ||
| + | * Notice the height of the camera. Position the camera to point to the center of imaginary rectangle where laser pointers mark the corners. Actually the center is marked with a blue masking tape triangle. | ||
| + | {| | ||
| + | |valign='top'|[[File:SFE focusing tripod.jpeg|thumb|200px|Fig.5 Tripod placement]] | ||
| + | |valign='top'|[[File:SFE focusing tripod closer.jpeg|thumb|200px|Fig.6 Tripod closeup]] | ||
| + | |} | ||
| + | * Make sure all 4 lasers are pointing in the right spots - "manual laser pointers" yellow button in the imagej plugin | ||
| + | {| | ||
| + | |valign='top'|[[File:SFE focusing laser spots.jpeg|thumb|200px|Fig.7 Laser spot markings]] | ||
| + | |} | ||
| + | |||
| + | * Turn off the room lights. | ||
| + | * Turn on the patter lights if they are not on automatically. | ||
| + | * No need to close the garage door. | ||
| + | * Now proceed with '''[[Focus_adjustment_393#regular_SFE|regular_SFE]]''' instructions. | ||
Latest revision as of 15:56, 2 October 2020
Contents
Description
internal use
Regular SFE
- used on big the Xeon PC - 192.168.0.6
- restore from /home/elphel/test_focusing/default.conf-xml
- quick get&show
- find grid (if error - increase/decrease exposure using the 'camera settings' button - the range is 2.5-5.0 ms - rerun steps 3. and 4.)
- no-move measure
- show PSF
- adjust screws
- repeat from 5. until good (if some PSF spots are missing - repeat from 4.)
Setup before using ImageJ Aberration Calibration plugin
Parts
- Assembled SFE without lens and without IR-cut filter (can be with the filter if the target lens is different)
- M12 adapter
- 2 spacers: 5mm and 4.7mm (shaved off 0.3mm (made from 5mm spacer) for optimal adjustment)
- Lens N125B04530W with IR-cut filter. If the target lens is different, still use this one for adjustment then replace. Wrap the thread of the lens with the teflon tape for better thread fitting - 2 layers is enough. When screwing in make sure the tape does not get in the optical path. Screw in the lens until full stop.
- Focus adjustment screws - do not overtighten initially. Later, right before starting the procedure when the camera is against the pattern - turn it on, while in jpeg open the control interface and adjust the screws for the best manual focus (do not apply too much force).
Assembled setup
- Take a longer cable - at least 100mm
- Connect to port 0
- Set the camera address to 192.168.0.38
# temporary (ssh will freeze, connect from another window) ~# ifconfig eth0 192.168.0.38 # permanently (reboot required) edit /etc/network/interfaces
- Make sure the power supply provides the right voltage - 12V or 48V. If possible install PoE compatible power board - 10386.
Pattern
- Use the wallpaper pattern.
- Notice the distance from the pattern.
- Notice the height of the camera. Position the camera to point to the center of imaginary rectangle where laser pointers mark the corners. Actually the center is marked with a blue masking tape triangle.
- Make sure all 4 lasers are pointing in the right spots - "manual laser pointers" yellow button in the imagej plugin
- Turn off the room lights.
- Turn on the patter lights if they are not on automatically.
- No need to close the garage door.
- Now proceed with regular_SFE instructions.
