Difference between revisions of "Microzed issues"
From ElphelWiki
| Line 26: | Line 26: | ||
* Clear the RX disable and TX disable bits and then set the TX enable | * Clear the RX disable and TX disable bits and then set the TX enable | ||
* bit and RX enable bit to enable the transmitter and receiver.</i> | * bit and RX enable bit to enable the transmitter and receiver.</i> | ||
| + | <b>Links:</b> | ||
| + | * https://forums.xilinx.com/t5/Zynq-All-Programmable-SoC/Zynq-Uart-timeout-problem/td-p/432016 | ||
| + | * http://www.makelinux.net/ldd3/chp-7-sect-3 | ||
| + | </font> | ||
| − | |||
* SSH terminal | * SSH terminal | ||
<font size='2'> | <font size='2'> | ||
| Line 45: | Line 48: | ||
==Useful pages== | ==Useful pages== | ||
| − | |||
* http://processors.wiki.ti.com/index.php/Enabling_Stack_Dumping_in_Linux_Kernel | * http://processors.wiki.ti.com/index.php/Enabling_Stack_Dumping_in_Linux_Kernel | ||
| − | * https://lists.yoctoproject.org/pipermail/poky/2015-February/010037.html | + | * https://lists.yoctoproject.org/pipermail/poky/2015-February/010037.html - change hostname in poky |
* http://www.makelinux.net/ldd3/chp-7-sect-3 | * http://www.makelinux.net/ldd3/chp-7-sect-3 | ||
Revision as of 13:06, 19 February 2016
List
- [SOLVED] UART
Description:
UART register contents: timeout=0 rxfifo_level=56, should be timeout=10 rxfifo_level=56
minicom prints 56 symbols at a time when rxfifo reaches its level.
remembers all typed symbols
sometimes the timeout register is set correctly
Possible reason:
In driver .startup and .termios conflict? Race Reset?
Solution:
Added a delay after reset - some other functions in the driver also have it - some not. Luck?
Patch:
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index f214c7f..164e32d 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -704,6 +704,9 @@ static void cdns_uart_set_termios(struct uart_port *port,
ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
+ while (cdns_uart_readl(CDNS_UART_CR_OFFSET) &
+ (CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST))
+ cpu_relax();
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
Links:
* https://forums.xilinx.com/t5/Zynq-All-Programmable-SoC/Zynq-Uart-timeout-problem/td-p/432016
* http://www.makelinux.net/ldd3/chp-7-sect-3
- SSH terminal
Description:
Freezes, lags but remembers all typed symbols
Possible reason:
UART problem?
- RTC
Too many messages when rtc is missing
Description:
3x"hwclock: can't open '/dev/misc/rtc': No such file or directory" in boot log
Possible reason:
driver
