Difference between revisions of "Driverless mode 393"

Revision as of 08:46, 3 April 2018

Description

Instructions on how to disable sensor driver and get images from image sensor (for MT9F002 sensor)

Instructions

pre

• to load bitstream for MT9F002 appropriate changes need to be made to:
  • device tree

set sensors to mt9f002 in elphel393-detect_sensors,sensors entry

• • /etc/elphel393/default_10389.xml for setup w/o 10389 or 10389's eeprom otherwise write MT9F002 as application
• Disable driver

root@elphel393~# touch /etc/elphel393/disable_driver
# then reboot

init

• start python session:

root@elphel393~# cd /usr/local/verilog/; test_mcntrl.py @hargs-after

• init (if the driver is not disabled the i2c writes will not work):

setup_all_sensors True None 0x1 False 4384 3280

write_sensor_i2c 0 1 0 0x31c08000 # hispi timing
write_sensor_i2c 0 1 0 0x030600b4 # pll multiplier
write_sensor_i2c 0 1 0 0x31c68400 # hispi control status
write_sensor_i2c 0 1 0 0x306e9280 # datapath select
write_sensor_i2c 0 1 0 0x301a001c # reset and start streaming

hispi_phases_adjust 0

write_sensor_i2c 0 1 0 0x301a001c # reset and start streaming

setup_all_sensors True None 0x1 False 4384 3280
compressor_control all None None None None None 2
program_gamma all 0 0.57 0.04

write_sensor_i2c 0 1 0 0x3028000a # global gain
write_sensor_i2c 0 1 0 0x302c000d # some gain
write_sensor_i2c 0 1 0 0x302e0010 # some gain
write_sensor_i2c 0 1 0 0x30120080 # coarse exposure

jpeg_acquire_write

#write_sensor_i2c 0 1 0 0x301a0018 # put to standby

• inspect image:

http://192.168.0.9/img.jpeg

Example: 1600x1200

8-bit compress to jpeg

• setup:

write_sensor_i2c 0 1 0 0x3002001e
write_sensor_i2c 0 1 0 0x300604f5
write_sensor_i2c 0 1 0 0x034e04d8
write_sensor_i2c 0 1 0 0x300a056a
write_sensor_i2c 0 1 0 0x30040090
write_sensor_i2c 0 1 0 0x300806cf
write_sensor_i2c 0 1 0 0x034c0640
write_sensor_i2c 0 1 0 0x300c04c8

setup_all_sensors True None 0x1 False 1600 1200
compressor_control all None None None None None 2

write_sensor_i2c 0 1 0 0x301a001c
# wait
write_sensor_i2c 0 1 0 0x301a0018

jpeg_acquire_write

• inspect:

refresh http://192.168.0.9/img.jpeg

8-bit raw

• setup

same as above, no need to repeat if already done

• capture

setup_all_sensors True None 0x1 False 1600 1200

write_sensor_i2c 0 1 0 0x301a001c
# wait
write_sensor_i2c 0 1 0 0x301a0018

# notice membridge_start (under Setting membridge for sensor 0)
# it can be different 0x2e000000 or 0x2dc00000

membridge_start
mem_save "/usr/local/verilog/sensor_dump" 0x2e000000 0x400000

Notice membridge_start_address

16-bit raw