Difference between revisions of "Porting Theora to 353 cameras"

Revision as of 05:26, 22 February 2008

Elphel model 333 cameras were able to encode and stream Ogg Theora with 6.3.9 firmware. However, this model is no longer produced by Elphel. The goal of this project is to use the full potential of 353 cameras (larger FPGA, faster CPU) in order to port the Ogg Theora feature on the new hardware. First, the camera should be able to upload small Theora clips via FTP.

Different solutions are possible as previously mentioned in the Theora page :

• Instantiate both the Theora compressor and the MJPEG compressor in the FPGA since the new Spartan 3E seems to be large enough to handle the two features.
• Replace the existing MJPEG compressor with the Theora compressor and implement software Theora to JPEG conversion if JPEG is needed.
• Replace the existing MJPEG compressor in the 353 camera with the Theora compressor and keep two configuration files on the camera filesystem (one for Theora the other for MJPEG). FPGA code could be changed at run-time according to the needs.

Dealing with the last solution seems to be a good start for this project as the other features mentioned can be added later. In all cases, both FPGA code and software code will need to be adapted.

Hardware updates

Compressor

Replace the MJPEG compressor in the 353 with the 333 Theora compressor (333 Theora FPGA code). Maybe some adaptations need to be done within the Theora compressor itself. However, assuming that the compressor worked in 333 cameras a simple instantiation should suffice.

Memory controller

Replace the 4-channel memory controller with an 8-channel memory interface as in the 333 model in order to handle Theora specific data.

System Interface

Adapt the system interface to assure communication between FPGA and its environment.

A feature of the system interface is to establish communication between the system CPU and the different blocks within the FPGA (compressor, memory controller etc). This is done by selecting a block with the address bus a[12:0] connected to the internal address bus ial[7:0]:

x353.v
always @ (posedge cwr) begin
   a0[7:0]<=ial[7:0];  // may want to change to just ia if ia will be late enough;
   wnr0                <= ~irnw;
   da_ctl0             <= (ial[7:0]==8'h00);  // 0x00 WE to control 32-bit register (1 loc)
   da_dmamode0         <= (ial[7:0]==8'h01);  // 0x01 select writing to dma_cntr/dma_raw (1 loc)
   da_sensormode0      <= (ial[7:0]==8'h02);  // 0x02 select writing to sensorpix (1 loc)
   ...
   da_compressor0      <= (ial[7:1]==7'h06);  // 0x0c..0x0d - will be farther decoded in the compressor module
   ...

Since memory controller and compressor are to be replaced these addresses have to be adapted.

353 system interface address table

333 system interface address table

Addresses 0x01,2,3,4,5,6,8 and 0x30 can be kept in the 353 system interface. The interrupt mask address 0x06 in the 333 sys interface is no longer used (353 uses interrupt vectors). The Theora compressor and the new memory controller addresses have to be mapped again in the new design (addresses 0x0c..0x0d and 0x20 to 0x2f).

Interrupts

Adapt the Theora compressor interrupts to the 353 interrupt vector .

The 353 interrupt vector can handle up to 16 different irq. However, only irq 0 to 8 are used :

x353.v

assign irq_in= {8'b0,                    // extra
               compressor_done_compress, // 7 - will go high after all data is sent out (reset by compressor)
               compressor_done_input,    // 6 - will go high after EOT and persist until DCT is enabled (reset by compressor)
               dcc_rdy,                  // 5 - obsolete in 333 - channel3 has 128 more dc coefficients (or some if the compression is finished)
               compressor_eot,           // 4 - compressor read in the last MCU (predictable time to end of transfer)
               sr_sensortrig[2],         // 3 - (sync to pclk) - level, reset by writing to sensor triggering command register
               xfer_over_irq,            // 2 - (sync to pclk) - frame acquisition over
               trig_irq,                 // 1 - (sync to pclk) - external trigger
               vacts};                   // 0 - (sync to pclk) - frame sync

353 MJPEG compressor triggers irqs 4, 6 and 7. 333 Theora compressor is the source of two irqs :

compressor_all.v

done,           // single-cycle pulse when the compressed frame is sent out (IRQ source).
reset_compress, // reset compressor done interrupt (writing any compressor command)

Adaptation should consist of assigning Theora compressor irq sources to vectors 6 and 7 for example if the MJPEG compressor is to be replaced.

DMA FIFOs

353 design uses 2 DMA FIFOs between the compressor and the system interface instead of one for the 333 Theora compressor. The two DMA FIFOs have also slight differences between the two design. Maybe a single 333 FIFO should be kept for the final design (?)

Others

• Looks like Theora compressor requires 90° phase clock that was abandoned in the 353 design.
• Is it necessary to keep histogram and timestamp blocks in a design which supports Theora only ? If not, some code will have to be removed from sysinterface and mcontr.
• ...?

Software updates

• Adapt FPGA definitions (x353.h) and most likely some other FPGA drivers.
• ...?

These lists of update are obviously incomplete. They need to be more detailed in order to make an exhaustive list of the changes that have to be done.

See also

• Theora
• FPGA Development in Elphel cameras
• FPGA Theora Encoder for Videoconferencing
• 10353