Difference between revisions of "10369"

Revision as of 09:47, 26 June 2008

10369

10369 board, top view

10369 board, bottom view

10369 Circuit Diagram, Parts List, PCB layout 10369 Gerber files

103691: Dual CF card adapter/riser board

103692: 1.8" ZIF-type HDD adapter board

103693: External USB connector adapter board

Features

10369 interface board is an extension board for the Elphel 353/363 series cameras.

It provides multiple interfaces and peripherals to the camera:
- SATA port for external disk drives
- Compact Flash (in "True IDE" mode) and IDE HDD ports (with adapter/riser boards: 103691, 103692)
- RS-232 port
- Opto-isolated I/O port for synchronizing the camera or synchronizing together multiple cameras (modular RJ14 external connector)
- Opto-isolated I/O port for synchronizing multiple camera modules in the same enclosure (flex cable connectors)
- Digital thermometer with internal ("system") and external thermal sensor (emitter-base junction of PNP or NPN transistor)
- Fan driver, controlled by the digital thermometer with programmable on/off temperature
- Clock/calendar with the super-capacitor backup power
- EEPROM for the board identification and configuration

Connectors

J1 - AUX (from the CPU board)

AUX connector (from 10353)
Pin	Signal	Notes	Pin	Signal	Notes
1	GND		2	GND
3	EXT[0]	GPIO	4	EXT[2]	GPIO
5	EXT[1]	GPIO	6	EXT[3]	GPIO
7	GND		8	GND
9	EXT[4]	GPIO	10	EXT[6]	GPIO
11	EXT[5]	GPIO	12	EXT[7]	GPIO
13	GND		14	GND
15	EXT[8]	GPIO	16	EXT[10]	GPIO
17	EXT[9]	GPIO	18	EXT[11]	GPIO
19	GND		20	GND
21	CTS	RS232	22	RTS	RS232
23	RXD	RS232	24	TXD	RS232
25	VP33	+3.3V	26	VP33	+3.3V
27	U0VM	USB	28	U0VP	USB
29	VP33	+3.3V	30	VP33	+3.3V

J2 - IDE (from the CPU board)

IDE connector (from 10353)
Pin	Signal	Pin	Signal	Notes
1	IDE_RST	2	GND
3	IDE_D[7]	4	IDE_D[8]
5	IDE_D[6]	6	IDE_D[9]
7	IDE_D[5]	8	IDE_D[10]
9	IDE_D[4]	10	IDE_D[11]
11	IDE_D[3]	12	IDE_D[12]
13	IDE_D[2]	14	IDE_D[13]
15	IDE_D[1]	16	IDE_D[14]
17	IDE_D[0]	18	IDE_D[15]
19	GND	20	GND
21	IDE_DMARQ	22	GND
23	IDE_IOW	24	GND
25	IDE_IOR	26	GND
27	IDE_IORDY	28	GND
29	IDE_DMACK	30	GND
31	IDE_INTRQ	32	EXT_OE	not used
33	IDE_A[1]	34	--
35	IDE_A[0]	36	IDE_A[2]
37	IDE_CS0	38	IDE_CS1
39	--	40	GND

J3 - Power (from the CPU board)

Power connector (from 10353)
Pin	Signal	Notes		Pin	Signal	Notes
1	GND			3	VP33	+3.3V
2	LPWR48M	-48V, isolated, primary		4	LPWR48P	+48V, isolated, primary

Note: +/- 48V are non-regulated input power rails. For 12V or 24V camera modifications these lines will also have +/-12V or +/-24V.

J4 - Power (optional - to the next boards)

Power connector (optional - to the next boards)
Pin	Signal	Notes		Pin	Signal	Notes
1	GND			3	VP33	+3.3V
2	LPWR48M	-48V, isolated, primary		4	LPWR48P	+48V, isolated, primary

Note: J4 is normally not installed. It is used in some camera modificatios where ther is another board on top of the 10369 that needs power - J4 is located oppposite to J3, same as on 10353 system board.

J5 - Power (optional 3.3V in)

Power connector (optional 3.3V in)
Pin	Signal	Notes
1	GND
2	VP33	+3.3V
3	LPWR48M	-48V, isolated, primary
4	LPWR48P	+48V, isolated, primary

Note: J5 is normally not installed. It may be used in multi-camera systems to provide 3.3V from the commomn to all camera modules power supply (DC-DC converter on 10353 should not be installed).

J6 - IDE (to adapter/riser)

IDE connector to adpaters/risers (103691, 103692)
Pin	Signal	Notes	Pin	Signal	Notes
1	CF1PRESENT	GND if CF1 installed	2	GND
3	IDE_D[11]		4	IDE_D[3]
5	IDE_D[12]		6	IDE_D[4]
7	IDE_D[13]		8	IDE_D[5]
9	IDE_D[14]		10	IDE_D[6]
11	IDE_D[15]		12	IDE_D[7]
13	IDE_CS1		14	IDE_CS0
15	--		16	--
17	IDE_IOR		18	GND
19	IDE_IOW		20	--
21	--		22	--
23	IDE_INTRQ		24	--
25	+3.3V		26	+3.3V
27	GND		28	EXT[0](SCL)
29	RST_CFS	Reset master	30	EXT[0](SDA)
31	RST_CFM	Reset slave	32	IDE_A[2]
33	IDE_IORDY		34	--
35	IDE_DMARQ		36	IDE_A[2]
37	IDE_DMACK		38	IDE_A[1]
39	IDE_DASP		40	IDE_A[0]
41	IDE_PDIAG		42	IDE_D[0]
43	IDE_D[8]		44	IDE_D[1]
45	IDE_D[9]		46	IDE_D[2]
47	IDE_D[10]		48	--
49	GND		50	CF0PRESENT	GND if CF0 installed

J7 - SATA

SATA 7-pin connector to HDD
Pin	Signal	Notes
1	GND
2	SATATP	Transmit +
3	SATATM	Transmit -
4	GND
5	SATARM	Receive -
6	SATARP	Receive +
7	GND

J8 - USB0 (to external)

USB to 103693 adapter - external connector
Pin	Signal	Notes
1	GND	System ground, needs series inductor (on 103693)
2	DP1	USB data +
3	DM1	USB data -
4	PW1	USB +5V power (switched)
5	GND
6	EXT[0]	i2c SCL
7	EXT[1]	i2c SDA
8	EXT[6]	GPIO
9	EXT[7]	GPIO
10	P3_1	+3.3V power

J9 - USB1 (to internal)

USB , i2c, GPIO, 3.3V power to extension boards
Pin	Signal	Notes
1	GND
2	DP2	USB data +
3	DM2	USB data -
4	PW2	USB +5V power (switched)
5	GND
6	EXT[0]	i2c SCL
7	EXT[1]	i2c SDA
8	EXT[2]	GPIO
9	EXT[3]	GPIO
10	P3_2	+3.3V power

J10 - USB2 (to internal)

USB , i2c, GPIO, 3.3V power to extension boards
Pin	Signal	Notes
1	GND
2	DP3	USB data +
3	DM3	USB data -
4	PW3	USB +5V power (switched)
5	GND
6	EXT[0]	i2c SCL
7	EXT[1]	i2c SDA
8	EXT[4]	GPIO
9	EXT[5]	GPIO
10	P3_3	+3.3V power

J11 - USB4 (to internal)

USB , i2c, GPIO, 3.3V power to extension boards
Pin	Signal	Notes
1	GND
2	DP4	USB data +
3	DM5	USB data -
4	PW4	USB +5V power (switched)
5	GND
6	EXT[0]	i2c SCL
7	EXT[1]	i2c SDA
8	EXT[6]	GPIO
9	EXT[7]	GPIO
10	P3_4	+3.3V power

J12 - SYNC (internal, master)

Interboard synchronization I/O, master, bottom contacts
Pin	Signal	Notes
1	GND	Driver return
2	ISYNCDR	Driver output
3	ISYNC1	Optoisolated I/O
4	ISYNC2	Optoisolated I/O return

Note: Connect J12 to J14 on the next camera in chain with a 4-conductor flex jumper, then from J13 of that next camera to the next in chain's J14, and so on. J12 and J13 have contacts on the bottom side, J14 - on the top to simplify chaining.

J13 - SYNC (internal, slave)

Interboard synchronization I/O, slave, bottom contacts
Pin	Signal	Notes
1	ISYNC2	Optoisolated I/O return
2	ISYNC1	Optoisolated I/O
3	ISYNC1	Optoisolated I/O
4	ISYNC2	Optoisolated I/O return

Note: Connect J12 to J14 of the next camera module in chain.

J14 - SYNC (internal, slave)

Interboard synchronization I/O, slave, top contacts
Pin	Signal	Notes
1	ISYNC2	Optoisolated I/O return
2	ISYNC1	Optoisolated I/O
3	ISYNC1	Optoisolated I/O
4	ISYNC2	Optoisolated I/O return

Note: Connect J14 to J13 of the previous camera module in chain (if the previous is not the master). If it is the master, connect J14 to the master's J12 instead of the J13

J15 - SYNC (external)

Intercamera synchronization I/O, modular RJ-14
Pin	Signal	Notes
1	GND	Driver return
2	XSYNC1	Optoisolated I/O
3	XISYNC2	Optoisolated I/O return
4	XSYNCDR	Driver output

Note: In order to synchronize multiple cameras connect the pins 2 on all cameras together, same for all the pins 3. Additionally connect pin 1 on the 'master' (synchronization source) camera to pin 3, pin 4 - with pin2.

J16 - RS-232

Serial RS-232 port, modular RJ-25
Pin	Signal	Notes
1	XCTS	CTS
2	XRXD	RxD
3	GND
4	GND
5	XTXD	TxD
6	XRTS	RTS

J17 - Fan

Optional Fan connection (3.3V/5.0V)
Pin	Signal	Notes
1	FANPOS	Fan positive terminal
2	GND	Fan negative terminal

Note: Default configuration supports 3.3VDC fans, in order to switch to 5.0V you need to open (cut trace) jumper JP2 and close (solder together terminals of) jumper JP1.

W2-W4 - Terminals for external temperature sensor

Solder terminals for optional thermal sensor
Pin	Signal	Notes
W2	TSNSP	Thermal sensor positive
W3	TSNSP	Thermal sensor positive
W3	GND	connect to sensor cable shield

Note: small NPN (i.e. 2N3904) or PNP (i.e. 2N3906) can be used as an external sensor. Connect NPN base (or PNP emitter) to W2, NPN emitter (or PNP base) to W3 (W4 may be connected to the shield around these two wires that shoul be twisted). If no sensor is used W2 and W3 should be connected together to enable fan control.

@@ Line 8: / Line 8: @@
 [[Image:103693_sm.jpeg|frame|[[Media:103693.jpeg|103693: External USB connector adapter board]]]]
+=== Features ===
 interface board is an extension board for the [[353|Elphel 353/363 series cameras]].
 * It provides multiple interfaces and peripherals to the camera:
@@ Line 19: / Line 20: @@
 ** Clock/calendar with the super-capacitor backup power
 ** EEPROM for the board identification and configuration
-==== Connectors ====
+=== Connectors ===
 ----
-===== J1 - AUX (from the CPU board) =====
+==== J1 - AUX (from the CPU board) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ AUX connector (from 10353)
@@ Line 65: / Line 66: @@
 ----
-===== J2 - IDE (from the CPU board) =====
+==== J2 - IDE (from the CPU board) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
@@ Line 117: / Line 118: @@
 ----
-===== J3 - Power (from the CPU board) =====
+==== J3 - Power (from the CPU board) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Power connector (from 10353)
@@ Line 133: / Line 134: @@
 ----
-===== J4 - Power (optional - to the next boards) =====
+==== J4 - Power (optional - to the next boards) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Power connector (optional - to the next boards)
@@ Line 149: / Line 150: @@
 ----
-===== J5 - Power  (optional 3.3V in) =====
+==== J5 - Power  (optional 3.3V in) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Power connector (optional 3.3V in)
@@ Line 168: / Line 169: @@
 ----
-===== J6 - IDE (to adapter/riser) =====
+==== J6 - IDE (to adapter/riser) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ IDE connector to adpaters/risers (103691, 103692)
@@ Line 229: / Line 230: @@
 ----
-===== J7 - SATA =====
+==== J7 - SATA ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ SATA 7-pin connector to HDD
@@ Line 254: / Line 255: @@
 ----
-===== J8 - USB0 (to external) =====
+==== J8 - USB0 (to external) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ USB to 103693 adapter - external connector
@@ Line 285: / Line 286: @@
 ----
-===== J9 - USB1 (to internal) =====
+==== J9 - USB1 (to internal) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ USB , i2c, GPIO, 3.3V power to extension boards
@@ Line 316: / Line 317: @@
 ----
-===== J10 - USB2 (to internal) =====
+==== J10 - USB2 (to internal) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ USB , i2c, GPIO, 3.3V power to extension boards
@@ Line 347: / Line 348: @@
 ----
-===== J11 - USB4 (to internal) =====
+==== J11 - USB4 (to internal) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ USB , i2c, GPIO, 3.3V power to extension boards
@@ Line 378: / Line 379: @@
 ----
-===== J12 - SYNC (internal, master) =====
+==== J12 - SYNC (internal, master) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Interboard synchronization I/O, master, bottom contacts
@@ Line 398: / Line 399: @@
 ----
-===== J13 - SYNC (internal, slave) =====
+==== J13 - SYNC (internal, slave) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Interboard synchronization I/O, slave, bottom contacts
@@ Line 418: / Line 419: @@
 ----
-===== J14 - SYNC (internal, slave) =====
+==== J14 - SYNC (internal, slave) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Interboard synchronization I/O, slave, top contacts
@@ Line 438: / Line 439: @@
 ----
-===== J15 - SYNC (external) =====
+==== J15 - SYNC (external) ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Intercamera synchronization I/O, modular RJ-14
@@ Line 458: / Line 459: @@
 ----
-===== J16 - RS-232 =====
+==== J16 - RS-232 ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Serial RS-232 port, modular RJ-25
@@ Line 481: / Line 482: @@
 ----
-===== J17 - Fan =====
+==== J17 - Fan ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Optional Fan connection (3.3V/5.0V)
@@ Line 497: / Line 498: @@
 ----
-===== W2-W4 - Terminals for external temperature sensor =====
+==== W2-W4 - Terminals for external temperature sensor ====
 {|  class="wikitable" style="background:#fcfcfc; "  border="1"
 |+ Solder terminals for optional thermal sensor

Difference between revisions of "10369"

Revision as of 09:47, 26 June 2008

Contents