NAND flash boot rootfs

Reflash factory image

Notes

• Will overwrite software/firmware or corrupt flash partition
• To update u-boot images, device tree and kernel - booting from micro SD card is not required.
• To update rootfs - boot from micro SD card otherwise a mounted flash partition will be rewritten, get corrupt and the camera might not boot - to recover, boot from micro SD card and reflash rootfs partition.
• boot.bin, u-boot-dtb.img - most likely won't need updating at all. Only if their partitions get corrupt
  • As Zynq's BootROM performs 32KB jumps within the first 128MiB of flash in the search of a boot.bin header with a correct checksum it is possible to flash a few backup images to the 1st flash partition (mtd0) in the device tree. The partition size is 1MB, boot.bin size is normally around 100KB (<192KB - Zynq's OCM requirement)

• Considering to store u-boot (probably not, because 192K-max-boot.bin might not fit UBIFS driver), device tree and kernel on UBIFS partitions in future. SPL has to be either on the NAND flash or MMC

Instructions

• Use files from elphel393/bootable-images/elphel393/nand/
  • boot.bin
  • u-boot-dtb.img
  • devicetree.dtb
  • uImage
  • rootfs.ubi or rootfs.ubifs

Option 1: web browser

• Boot the camera from the micro SD card (important for rootfs update)
• Go to the http://192.168.0.9/update_software.html
• Upload uImage and rootfs.ubi
• Verify-button, download backup then Flash-button

Option 2: command line

• Boot the camera from the micro SD card (important for rootfs update)
• Copy file to the camera, example from the PC terminal:

$ scp boot.bin u-boot-dtb.img devicetree.dtb uImage rootfs.ubi root@192.168.0.9:/<path-to-image-files>/

• From the ssh session (ssh root@192.168.0.9) reflash what needs an update:
  • Reflash rootfs (rootfs.ubi, /dev/mtd4) (radical)

cd <path-to-image-files>
flash_unlock /dev/mtd4
flash_erase /dev/mtd4 0 2048
ubiformat /dev/mtd4 -f rootfs.ubi -s 2048 -O 2048

OR

• • update rootfs (rootfs.ubifs, /dev/mtd4) (recommended)

flash_unlock /dev/mtd4
ubiattach /dev/ubi_ctrl -m 4
# NOT NEEDED: ubimkvol /dev/ubi0 -N elphel393-rootfs -s 256MiB
ubiupdatevol /dev/ubi0_0 rootfs.ubifs
# 
# read: http://www.linux-mtd.infradead.org/faq/ubifs.html
# read: http://free-electrons.com/blog/creating-flashing-ubi-ubifs-images/
# read: http://www.linux-mtd.infradead.org/doc/ubi.html#L_volupdate
# read: http://comments.gmane.org/gmane.linux.drivers.mtd/39415

• • Reflash kernel (uImage, /dev/mtd3)

cd <path-to-image-files>
# uImage
# mtd3 is 16M (128 eraseblocks,128K = 1 block, there are 64 pages of 2048 per block)
flash_unlock /dev/mtd3
flash_erase /dev/mtd3 0 128
nandwrite -n /dev/mtd3 -p uImage

• • Reflash devicetree (devicetree.dtb, /dev/mtd2)

cd <path-to-image-files>
# u-boot-dtb.img
# mtd2 is 1M (8 eraseblocks,128K = 1 block, there are 64 pages of 2048 per block)
flash_unlock /dev/mtd2
flash_erase /dev/mtd2 0 8
nandwrite -n /dev/mtd2 -p devicetree.dtb

• • Reflash u-boot (u-boot-dtb.img, /dev/mtd1)

cd <path-to-image-files>
# u-boot-dtb.img
# mtd1 is 4M (32 eraseblocks,128K = 1 block, there are 64 pages of 2048 per block)
# erase only the 1st 8 blocks as image is <1M, leave unused area for backup copies
flash_unlock /dev/mtd1
flash_erase /dev/mtd1 0 8
nandwrite -n /dev/mtd1 -p u-boot-dtb.img

• • Reflash SPL (boot.bin, /dev/mtd0)

cd <path-to-image-files>
# boot.bin
# mtd0 is 1MB (8 eraseblocks,128K = 1 block, there are 64 pages of 2048 per block)
# erase only first 2 blocks, other block are reserved for copies
flash_unlock /dev/mtd0
flash_erase /dev/mtd0 0 2
nandwrite -n /dev/mtd0 -p boot.bin