10369

10369 board, top view

10369 board, bottom view

10369 Circuit Diagram, Parts List, PCB layout 10369 Gerber files

10369 interface board is an extension board for the Elphel 353/363 series cameras.

It provides multiple interfaces and peripherals to the camera:
- SATA port for external disk drives
- Compact Flash (in "True IDE" mode) and IDE HDD ports (with adapter/riser boards: 103691, 103692)
- RS-232 port
- Opto-isolated I/O port for synchronizing the camera or synchronizing together multiple cameras (modular RJ11 external connector)
- Opto-isolated I/O port for synchronizing multiple camera modules in the same enclosure (flex cable connectors)
- Digital thermometer with internal ("system") and external thermal sensor (emitter-base junction of PNP or NPN transistor)
- Fan driver, controlled by the digital thermometer with programmable on/off temperature
- Clock/calendar with the super-capacitor backup power
- EEPROM for the board identification and configuration

Connectors

J1 - AUX

AUX connector (from 10353)
Pin	Signal	Notes	Pin	Signal	Notes
1	GND		2	GND
3	EXT[0]	GPIO	4	EXT[2]	GPIO
5	EXT[1]	GPIO	6	EXT[3]	GPIO
7	GND		8	GND
9	EXT[4]	GPIO	10	EXT[6]	GPIO
11	EXT[5]	GPIO	12	EXT[7]	GPIO
13	GND		14	GND
15	EXT[8]	GPIO	16	EXT[10]	GPIO
17	EXT[9]	GPIO	18	EXT[11]	GPIO
19	GND		20	GND
21	CTS	RS232	22	RTS	RS232
23	RXD	RS232	24	TXD	RS232
25	VP33	+3.3V	26	VP33	+3.3V
27	U0VM	USB	28	U0VP	USB
29	VP33	+3.3V	30	VP33	+3.3V

J2 - IDE

IDE connector (from 10353)
Pin	Signal	Pin	Signal	Notes
1	IDE_RST	2	GND
3	IDE_D[7]	4	IDE_D[8]
5	IDE_D[6]	6	IDE_D[9]
7	IDE_D[5]	8	IDE_D[10]
9	IDE_D[4]	10	IDE_D[11]
11	IDE_D[3]	12	IDE_D[12]
13	IDE_D[2]	14	IDE_D[13]
15	IDE_D[1]	16	IDE_D[14]
17	IDE_D[0]	18	IDE_D[15]
19	GND	20	GND
21	IDE_DMARQ	22	GND
23	IDE_IOW	24	GND
25	IDE_IOR	26	GND
27	IDE_IORDY	28	GND
29	IDE_DMACK	30	GND
31	IDE_INTRQ	32	EXT_OE	not used
33	IDE_A[1]	34	--
35	IDE_A[0]	36	IDE_A[2]
37	IDE_CS0	38	IDE_CS1
39	--	40	GND

J3 - Power

Power connector (from 10353)
Pin	Signal	Notes		Pin	Signal	Notes
1	GND			3	VP33	+3.3V
2	LPWR48M	-48V, isolated, primary		4	LPWR48P	+48V, isolated, primary

Note: +/- 48V are non-regulated input power rails. For 12V or 24V camera modifications these lines will also have +/-12V or +/-24V.

J4 - Power (optional - to the next boards)

Power connector (optional - to the next boards)
Pin	Signal	Notes		Pin	Signal	Notes
1	GND			3	VP33	+3.3V
2	LPWR48M	-48V, isolated, primary		4	LPWR48P	+48V, isolated, primary

Note: J4 is normally not installed. It is used in some camera modificatios where ther is another board on top of the 10369 that needs power - J4 is located oppposite to J3, same as on 10353 system board.

J5 - Power (optional 3.3V in)

Power connector (optional 3.3V in)
Pin	Signal	Notes
1	GND
2	VP33	+3.3V
3	LPWR48M	-48V, isolated, primary
4	LPWR48P	+48V, isolated, primary

Note: J5 is normally not installed. It may be used in multi-camera systems to provide 3.3V from the commomn to all camera modules power supply (DC-DC converter on 10353 should not be installed).

J6 - IDE (to adapter/riser)

IDE connector to adpaters/risers (103691, 103692)
Pin	Signal	Notes	Pin	Signal	Notes
1	CF1PRESENT	GND if CF1 installed	2	GND
3	IDE_D[11]		4	IDE_D[3]
5	IDE_D[12]		6	IDE_D[4]
7	IDE_D[13]		8	IDE_D[5]
9	IDE_D[14]		10	IDE_D[6]
11	IDE_D[15]		12	IDE_D[7]
13	IDE_CS1		14	IDE_CS0
15	--		16	--
17	IDE_IOR		18	GND
19	IDE_IOW		20	--
21	--		22	--
23	IDE_INTRQ		24	--
25	+3.3V		26	+3.3V
27	GND		28	EXT[0](SCL)
29	RST_CFS	Reset master	30	EXT[0](SDA)
31	RST_CFM	Reset slave	32	IDE_A[2]
33	IDE_IORDY		34	--
35	IDE_DMARQ		36	IDE_A[2]
37	IDE_DMACK		38	IDE_A[1]
39	IDE_DASP		40	IDE_A[0]
41	IDE_PDIAG		42	IDE_D[0]
43	IDE_D[8]		44	IDE_D[1]
45	IDE_D[9]		46	IDE_D[2]
47	IDE_D[10]		48	--
49	GND		50	CF0PRESENT	GND if CF0 installed

J7 - SATA

SATA 7-pin connector to HDD
Pin	Signal	Notes
1	GND
2	SATATP	Transmit +
3	SATATM	Transmit -
4	GND
5	SATARM	Receive -
6	SATARP	Receive +
7	GND

J8 - USB0 (to external)

USB to 103693 adapter - external connector
Pin	Signal	Notes
1	GND	System ground, needs series inductor (on 103693)
2	DP1	USB data +
3	DM1	USB data -
4	PW1	USB +5V power (switched)
5	GND
6	EXT[0]	i2c SCL
7	EXT[1]	i2c SDA
8	EXT[6]	GPIO
9	EXT[7]	GPIO
10	P3_1	+3.3V power