-
if [ -s $img ] ; then
if [ -s "$OUTFILE" ] ; then
2 KB (193 words) - 07:23, 15 June 2007
-
...ither earlier assigned MAC address (written in bootblock of the flash) or, if it is a brand new camera, temporary use random MAC address. Next step - run
...be used to read flash from the camera for postmortem analysis of the data if camera does not boot for some reason.
7 KB (1,207 words) - 16:19, 20 June 2009
-
Quality of image may be better if we include a manual iris to have more depth in the picture.
12 KB (1,769 words) - 09:59, 24 October 2018
-
...utton was pressed, do not attempt to reboot (it will fail or reflash again if the future bulk-flash daemon is still running) but just output message inst
It takes longer time to connect to the camera if the IP during netboot is the same as during normal boot, but MAC addresses
2 KB (280 words) - 23:51, 29 September 2007
-
...rd, so no 2 0xff bytes can appear together - this fact is used to find out if the data in the circular buffer was overwritten by the newer image frames.
...ligning them to the end of the 32-byte chunk, adding zeros before the data if needed. The last 4 bytes contain a 24-bit byte length of the JPEG data with
18 KB (2,955 words) - 00:26, 1 December 2007
-
...ar/state/exif.template'' is read in only once - at the imgsrv start up. So if you want to modify the Exif data attached to the camera images, you will ne
2 KB (319 words) - 00:05, 11 October 2007
-
...become available (it is possible that no waiting will actually take place if the image acquisition is ahead of the reading images out process. As far as
If issued with empty arguments (just <nowiki>http://<camera_ip>:8081/</nowiki>
9 KB (1,584 words) - 12:42, 27 January 2017
-
...ogram (0x200-0x27f for odd/all exposures, 0x280-0x2ff - for even ones) and if it is empty - programs default sequence (will not change existent sequence)
...to process the incoming sensor data you do not need to use ccam.cgi - only if any of the parameters above need to be changed, Later we'll develop new sof
13 KB (2,170 words) - 13:21, 30 October 2008
-
1852 if ((vp=paramValue(gparams, "iq"))) ioctl(devfd, _CCCMD(CCAM_WPARS , P_QUALI
...make this value as close as possible to the one specified by application, if the application passed the invalid value driver will use the corrected one.
6 KB (980 words) - 00:43, 17 October 2007
-
...rent cable length you may see image that looks like monochrome or purple - if the pixels are sampled at wrong time, red and green (also green and blue) p
Open the following URL in the browser (replace 192.168.0.9 if camera has different IP):
9 KB (1,508 words) - 15:06, 1 May 2022
-
..."1" for high level (near 3.3V) and "0" for low level (near zero volts), so if the signal is defined as output and set to output "1" it will read "1", unl
...he devices can read back) will be "1" if any of the outputs is "1" and "0" if all are "Z". Similarly it is possible to make a "wire-AND" by connecting ("
9 KB (1,380 words) - 01:36, 21 October 2007
-
...d to set "Program ahead" parameter to 5 instead of it's default value - 3. If not the camera freeze after the first frame.
935 bytes (148 words) - 06:44, 19 July 2010
-
* patched busybox hdparm utility to output large sectors if invoked as "hdparm -I"
Broken release, please remove it if you downloaded it during half-day it was posted @ SourceForge
32 KB (4,592 words) - 16:14, 26 September 2014
-
...in the GET request as well as the script name. Script uses default values if the parameters ("NFS=" and "SCRIPT=") are not specified.
The script returns XML response with error message or status OK if it went as far as starting remote script on NFS server. After that response
1 KB (216 words) - 01:18, 22 April 2009
-
= This is the sandbox. If you're new to Media-wiki systems, please edit here first =
212 bytes (29 words) - 03:53, 8 December 2010
-
...operations on the HDD will not cause the frame loss - that can be verified if the Exif headers are enabled - regardless of the format selected each frame
Eventually camogm will be started (and restarted if needed) automatically at boot time, now it is started manually with the com
24 KB (3,768 words) - 14:39, 11 July 2021
-
...ddress has been configured the script exits and thus needs to be restarted if the address is to be reconfigured.
The unit responds to the ping in the examples above if the new address was configured. Note, this method(ARP/ping mehtod above) on
4 KB (575 words) - 16:13, 24 October 2018
-
...p://192.168.0.9/var/''' in the web browser) - recommended for experiments, if something goes wrong you can just power-cycle the camera and all your chang
...mbers, not strings - you may want to use $value+0 (instead of just $value) if $value may be a string (i.e. passed from _GET[])''--[[User:Andrey.filippov|
36 KB (5,115 words) - 06:00, 8 February 2012
-
if it will be used to compile computer, restart which is not desirable and dis
knoppix# dd if=/dev/zero of=swapfile bs=1024 count=1024M
3 KB (450 words) - 07:59, 6 December 2007
-
logging all - good and bad, trying input type 'hidden' to see if the bots really load a page or generate on their own
248 bytes (45 words) - 16:49, 14 January 2008
