10393 manual

Connections

• Connect sensors to system board - FPC cables are not symmetrical
• Ports:

Defaults

IP addr: 192.168.0.8

user / pwd: root / <empty>

• The address is set in the init_elphel393.sh script on the card's FAT32 partition.

init_elphel393.sh

• Before boot set SENSOR_TYPE:
  • SENSOR_TYPE=5 - for 5MPix sensors
  • SENSOR_TYPE=14 - for 14MPix

NOTE: 5 & 14 MPix sensors cannot be mixed - require different bitstreams.

• Change the default IP address

Boot

• on power-on boots from NAND flash: u-boot, device tree and kernel.

devicetree has "chosen = ...root=/dev/mmcblk0p2..." - rootfs is on the micro SD card second partition.

Command line access

ssh root@192.168.0.8

Serial console access

• Use a microUSB-USB cable to connect to PC - the cable's end should be thin enough otherwise interferes with the micro SD card.

• Linux: minicom -c on
  • likely device: /dev/ttyUSB0
  • settings: 115200 8N1, no for hardware/software flow control

Get images

channel 1: http://192.168.0.8:2323/noexif/img

channel 2: http://192.168.0.8:2324/noexif/img

channel 3: http://192.168.0.8:2325/noexif/img

channel 4: http://192.168.0.8:2326/noexif/img

Video recording

• More info
• If prefix parameter for a channel is not set the file will be written somewhere to rootfs (likely /usr/local/verilog/)

browser

Example:

• channel 0, /dev/sda1, w/o a file name prefix, 1GB or 10min files whichever occurs first
  • setup:

http://192.168.0.8/camogm.php?channel=0&cmd=format=mov;exif=0;prefix=/mnt/sda1/;duration=600;length=1073741824;status=/tmp/camogm0.status;

• • start:

http://192.168.0.8/camogm.php?channel=0&cmd=start;

• • stop:

http://192.168.0.8/camogm.php?channel=0&cmd=stop;

command line

Example:

• channel 2, /home/root, file prefix=test_, 1GB or 10min files whichever occurs first
  • setup and start (in one line):

echo "format=mov;status=/var/tmp/camogm2.status;prefix=/home/root/test_;duration=600;length=1073741824;start" > /var/volatile/camogm_cmd2

• • stop recording:

echo "stop" > /var/volatile/camogm_cmd2
sync

Change parameters

• http://192.168.0.8/controls.html - previews and basic parameters:
  • Exposure - the values are in the sensor lines. Currently conversion to seconds is not correct.
  • WB - r,g,b gains
  • Quality - compression quality - individual for compressor but common for the buffer driver - it's better to have the same value for all channels.

• For 5MPix the startup settings are defined int the /usr/local/verilog/startup5 on the micro SD card, FAT32 partition:

...
-c write_sensor_i2c  all 1 0 0x9009001e (exposure)
-c write_sensor_i2c  all 1 0 0x9035000a (set all gains to 0xa)
-c write_sensor_i2c  all 1 0 0x902c000e (blue gain to 0xe)
-c write_sensor_i2c  all 1 0 0x9009001d (red gain to 0xd)
...

Temperature monitor

• http://192.168.0.8/hwmon.html:
  • T_shutdown - automatic shutdown temperature level

Proper shutdown

shutdown -hP now

Firmware image

• 20160601 (new)
• 20160526 (old)
• 20160524 (old)
• 20160519 (old)

Known problems

• Vertical artifacts in jpegs. Images are ok at 100% quality. Fixed, testing.
• http://192.168.0.8:232x/noexif/mimg - multipart jpeg displays corrupted frames from time to time. Reason: network bandwidth?
• Sometimes on power-on (NAND flash boot) cannot mount the card's rootfs partition. Kernel Panics. Power off/on. Soft "reboot -f" works ok.
• Changing exposure/quality/gains - can corrupt images - needs testing.