10369

From ElphelWiki
Jump to navigation Jump to search

10369

10369 board, top view
10369 board, bottom view
10369 Circuit Diagram, Parts List, PCB layout     10369 Gerber files

10369 interface board is an extension board for the Elphel 353/363 series cameras.

  • It provides multiple interfaces and peripherals to the camera:
    • SATA port for external disk drives
    • Compact Flash (in "True IDE" mode) and IDE HDD ports (with adapter/riser boards: 103691, 103692)
    • RS-232 port
    • Opto-isolated I/O port for synchronizing the camera or synchronizing together multiple cameras (modular RJ11 external connector)
    • Opto-isolated I/O port for synchronizing multiple camera modules in the same enclosure (flex cable connectors)
    • Digital thermometer with internal ("system") and external thermal sensor (emitter-base junction of PNP or NPN transistor)
    • Fan driver, controlled by the digital thermometer with programmable on/off temperature
    • Clock/calendar with the super-capacitor backup power
    • EEPROM for the board identification and configuration

Connectors

J1 - AUX
AUX connector (from 10353)
Pin Signal Notes Pin Signal Notes
1 GND 2 GND
3 EXT[0] GPIO 4 EXT[2] GPIO
5 EXT[1] GPIO 6 EXT[3] GPIO
7 GND 8 GND
9 EXT[4] GPIO 10 EXT[6] GPIO
11 EXT[5] GPIO 12 EXT[7] GPIO
13 GND 14 GND
15 EXT[8] GPIO 16 EXT[10] GPIO
17 EXT[9] GPIO 18 EXT[11] GPIO
19 GND 20 GND
21 CTS RS232 22 RTS RS232
23 RXD RS232 24 TXD RS232
25 +3.3V power 26 +3.3V
27 U0VM USB 28 U0VP USB
29 +3.3V power 30 +3.3V


J2 - IDE
IDE connector (from 10353)
Pin Signal Notes Pin Signal Notes
1 IDE_RST 2 GND
3 IDE_D[7] 4 IDE_D[8]
5 IDE_D[6] 6 IDE_D[9]
7 IDE_D[5] 8 IDE_D[10]
9 IDE_D[4] 10 IDE_D[11]
11 IDE_D[3] 12 IDE_D[12]
13 IDE_D[2] 14 IDE_D[13]
15 IDE_D[1] 16 IDE_D[14]
17 IDE_D[0] 18 IDE_D[15]
19 GND 20 GND
21 IDE_DMARQ 22 GND
23 IDE_IOW 24 GND
25 IDE_IOR 26 GND
27 IDE_IORDY 28 GND
29 IDE_DMACK 30 GND
31 IDE_INTRQ 32 EXT_OE not used
33 IDE_A[1] 34 --
35 IDE_A[0] 36 IDE_A[2]
37 IDE_CS0 38 IDE_CS1
39 -- 40 GND


J3 - Power
Power connector (from 10353)
Pin Signal Notes Pin Signal Notes
1 GND 3 +3.3V
2 -48V isolated, primary 4 +48V isolated, primary

Note: +/- 48V are non-regulated input power rails. For 12V or 24V camera modifications these lines will also have +/-12V or +/-24V.


J4 - Power (optional - to the next boards)
Power connector (optional - to the next boards)
Pin Signal Notes Pin Signal Notes
1 GND 3 +3.3V
2 -48V isolated, primary 4 +48V isolated, primary

Note: J4 is normally not installed. It is used in some camera modificatios where ther is another board on top of the 10369 that needs power - J4 is located oppposite to J3, same as on 10353 system board.


J5 - Power (optional 3.3V in)
Power connector (optional 3.3V in)
Pin Signal Notes Pin Signal Notes
1 GND 3 -48V isolated, primary
2 +3.3V 4 +48V isolated, primary

Note: J5 is normally not installed. It may be used in multi-camera systems to provide 3.3V from the commomn to all camera modules power supply (DC-DC converter on 10353 should not be installed).


J6 - IDE (to adapter/riser)
IDE connector to adpaters/risers (103691, 103692)
Pin Signal Notes Pin Signal Notes
1 CF1PRESENT GND if CF1 installed 2 GND
3 IDE_D[11] 4 IDE_D[3]
5 IDE_D[12] 6 IDE_D[4]
7 IDE_D[13] 8 IDE_D[5]
9 IDE_D[14] 10 IDE_D[6]
11 IDE_D[15] 12 IDE_D[7]
13 IDE_CS1 14 IDE_CS0
15 -- 16 --
17 IDE_IOR 18 GND
19 IDE_IOW 20 --
21 -- 22 --
23 IDE_INTRQ 24 --
25 +3.3V 26 +3.3V
27 GND 28 EXT[0](SCL)
29 RST_CFS Reset master 30 EXT[0](SDA)
31 RST_CFM Reset slave 32 IDE_A[2]
33 IDE_IORDY 34 --
35 IDE_DMARQ 36 IDE_A[2]
37 IDE_DMACK 38 IDE_A[1]
39 IDE_DASP 40 IDE_A[0]
41 IDE_PDIAG 42 IDE_D[0]
43 IDE_D[8] 44 IDE_D[1]
45 IDE_D[9] 46 IDE_D[2]
47 IDE_D[10] 48 --
49 GND 50 CF0PRESENT GND if CF0 installed
103691: Dual CF card adapter/riser board
103692: 1.8" ZIF-type HDD adapter board
103693: External USB connector adapter board
Retrieved from "https://wiki.elphel.com/index.php?title=10369&oldid=4341"