Eyesis gui

About

Eyesis GUI allows to:

• change sensors' settings
• change compression quality
• start/stop recording
• check images and monitor sub-units status information

Download & Install

Ubuntu Linux

Package name: elphel-eyesis-gui

Dependencies: apache2, php5

There is a prebuilt package for Ubuntu users at elphel-eyesis-gui PPA.

To install it, use the following commands, see help for more information.

 sudo add-apt-repository ppa:andersonnotgood/elphel
 sudo apt-get update
 sudo apt-get install elphel-eyesis-gui

Other platforms

• Get the sources from http://elphel.cvs.sourceforge.net/viewvc/elphel/eyesis353/elphel-eyesis-gui/
• Copy to you web server folder the following files:

eyesis.html, 
eyesis.js, 
camogmgui_multiple.php
jquery-ui-1.8.4.custom.tar.gz

• Unpack the archive (should get "jquery-ui-1.8.4.custom/")

User Guide

1. GUI page

http://127.0.0.1/eyesis.html

2. Quick Start

Fig.1 Color bars test pattern.

Note: There is a program called camogm for recording running on all 3 sub-cameras. Once the GUI page is accessed or refreshed a launch request is issued - it can take some time (~20-30sec).

• Set the IPs (correct ips are 192.168.0.xx1,192.168.0.xx2,192.168.0.xx3). Other parameters can be left default - access the GUI page. After camogms are started the "Camogm Status" will indicate that.
• Check the images

1. Go to the Other tab - switch on the Color bars pattern.
2. Press Get Previews button (it is ok if the images are cut from the bottom - it's the browser problem - just press the button again)
3. turn off the color pattern mode.

• Go to the Camera tab and press the Enable JP4 button.
• Make a test RECORD/STOP to check if all HDDs are present (the default RECORD delay is set to 5 seconds, so wait until camogm state becomes "running" then issue a STOP)
• RECORD
• Check camogm logs from time to time.

3. Tabs

Network

• Assign the correct IPs (currently works only in 192.168.0.x subnetwork + the correct IPs are 192.168.0.xx1,192.168.0.xx2, 192.168.0.xx3)
• Set refresh interval (status requests period) (can be left default)

Camogm

• HDDs are mounted with RECORD and unmounted with STOP.
• HDDs mount points are /var/0 - /var/7
• Prefix should be set to /var/0/ - /var/7/ (slash at the end is important). If the partition is less than 250GB an auto incrementing prefix change will be made.
• Split size, Split interval & Max frames - describe *.mov file split conditions. Whatever condition comes first it will result in a start of a new file.

Camera

• By default the autoexposure mode is ON with a 1ms maximum exposure. To turn it off go to "Other Parameters" link & AUTOEXP_ON=0

Quality

• Set Coring Index (the higher index the less the image size and so the quality is worse - default - 5, normal is 5-20).
• Control the compression quality.

Other

• "Manually" Mount/Unmount drives.
• ON/OFF color bars pattern.

4. Status & Errors

• Normally during the recording the buffers are not filled more than a half when the camogm state is "running". For "stopped" & "starting" the buffers can be filled arbitrarily.
• "Camogm last error code" = 5 - a frame wasn't written on the HDD in time. Although the recording will not be stopped - it is better to stop/start it.
• Check logs from time to time.
• If a HDD is not detected you'll get HDD low space error. Then reattach the HDD and reboot the corresponding camera (see the Other paragraph of this page).

Other

• telnet 192.168.0.xx1
• telnet 192.168.0.xx2
• telnet 192.168.0.xx3
• root/pass
• Soft reboot can be done in telnet session with a command "reboof -f" OR go to http://192.168.0.xxx -> Terminal and type the same there (the page will freeze because the camera will be rebooting)