10369

From ElphelWiki
Jump to: navigation, search

10369

10369 interface board is an extension board for the Elphel 353/363 series cameras.

  • It provides multiple interfaces and peripherals to the camera:
    • SATA port for external disk drives
    • Compact Flash (in "True IDE" mode) and IDE HDD ports (with adapter/riser boards: 103691, 103692)
    • RS-232 port
    • Opto-isolated I/O port for synchronizing the camera or synchronizing together multiple cameras (modular RJ11 external connector)
    • Opto-isolated I/O port for synchronizing multiple camera modules in the same enclosure (flex cable connectors)
    • Digital thermometer with internal ("system") and external thermal sensor (emitter-base junction of PNP or NPN transistor)
    • Fan driver, controlled by the digital thermometer with programmable on/off temperature
    • Clock/calendar with the super-capacitor backup power
    • EEPROM for the board identification and configuration

Connectors


J1 - AUX
AUX connector (from 10353)
Pin Signal Notes Pin Signal Notes
1 GND 2 GND
3 EXT[0] GPIO 4 EXT[2] GPIO
5 EXT[1] GPIO 6 EXT[3] GPIO
7 GND 8 GND
9 EXT[4] GPIO 10 EXT[6] GPIO
11 EXT[5] GPIO 12 EXT[7] GPIO
13 GND 14 GND
15 EXT[8] GPIO 16 EXT[10] GPIO
17 EXT[9] GPIO 18 EXT[11] GPIO
19 GND 20 GND
21 CTS RS232 22 RTS RS232
23 RXD RS232 24 TXD RS232
25 +3.3V power 26 +3.3V
27 U0VM USB 28 U0VP USB
29 +3.3V power 30 +3.3V



J2 - IDE
IDE connector (from 10353)
Pin Signal Notes Pin Signal Notes
1 IDE_RST 2 GND
3 IDE_D[7] 4 IDE_D[8]
5 IDE_D[6] 6 IDE_D[9]
7 IDE_D[5] 8 IDE_D[10]
9 IDE_D[4] 10 IDE_D[11]
11 IDE_D[3] 12 IDE_D[12]
13 IDE_D[2] 14 IDE_D[13]
15 IDE_D[1] 16 IDE_D[14]
17 IDE_D[0] 18 IDE_D[15]
19 GND 20 GND
21 IDE_DMARQ 22 GND
23 IDE_IOW 24 GND
25 IDE_IOR 26 GND
27 IDE_IORDY 28 GND
29 IDE_DMACK 30 GND
31 IDE_INTRQ 32 EXT_OE not used
33 IDE_A[1] 34 --
35 IDE_A[0] 36 IDE_A[2]
37 IDE_CS0 38 IDE_CS1
39 -- 40 GND



J3 - Power
Power connector (from 10353)
Pin Signal Notes Pin Signal Notes
1 GND 3 +3.3V
2 -48V isolated, primary 4 +48V isolated, primary

Note: +/- 48V are non-regulated input power rails. For 12V or 24V camera modifications these lines will also have +/-12V or +/-24V.



J4 - Power (optional - to the next boards)
Power connector (optional - to the next boards)
Pin Signal Notes Pin Signal Notes
1 GND 3 +3.3V
2 -48V isolated, primary 4 +48V isolated, primary

Note: J4 is normally not installed. It is used in some camera modificatios where ther is another board on top of the 10369 that needs power - J4 is located oppposite to J3, same as on 10353 system board.



J5 - Power (optional 3.3V in)
Power connector (optional 3.3V in)
Pin Signal Notes Pin Signal Notes
1 GND 3 -48V isolated, primary
2 +3.3V 4 +48V isolated, primary

Note: J5 is normally not installed. It may be used in multi-camera systems to provide 3.3V from the commomn to all camera modules power supply (DC-DC converter on 10353 should not be installed).



J6 - IDE (to adapter/riser)
IDE connector to adpaters/risers (103691, 103692)
Pin Signal Notes Pin Signal Notes
1 CF1PRESENT GND if CF1 installed 2 GND
3 IDE_D[11] 4 IDE_D[3]
5 IDE_D[12] 6 IDE_D[4]
7 IDE_D[13] 8 IDE_D[5]
9 IDE_D[14] 10 IDE_D[6]
11 IDE_D[15] 12 IDE_D[7]
13 IDE_CS1 14 IDE_CS0
15 -- 16 --
17 IDE_IOR 18 GND
19 IDE_IOW 20 --
21 -- 22 --
23 IDE_INTRQ 24 --
25 +3.3V 26 +3.3V
27 GND 28 EXT[0](SCL)
29 RST_CFS Reset master 30 EXT[0](SDA)
31 RST_CFM Reset slave 32 IDE_A[2]
33 IDE_IORDY 34 --
35 IDE_DMARQ 36 IDE_A[2]
37 IDE_DMACK 38 IDE_A[1]
39 IDE_DASP 40 IDE_A[0]
41 IDE_PDIAG 42 IDE_D[0]
43 IDE_D[8] 44 IDE_D[1]
45 IDE_D[9] 46 IDE_D[2]
47 IDE_D[10] 48 --
49 GND 50 CF0PRESENT GND if CF0 installed