103692

From ElphelWiki
Revision as of 14:40, 11 January 2010 by Oleg (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

103692 - Adapter board for ZIF-type 1.8" HDD

103692 is an adapter board used with the 10369 board to connect ZIF-type 1.8" hard drive to the Elphel Model 353 camera.

1.8" HDD proper cable connection

Notes

  • It can be impossible to mount an external SATA disk to the camera with an internal 18"HDD (NC353L-369A-HDD) as the internal disk (Toshiba MK1214GAH) does not react on master/slave-option bus and also it doesn't tristate the signals it shares with the SATA bridge.

Connectors


J1 - to 10369 board

connector to the 10369 board
Pin Signal Notes Pin Signal Notes
1 CF1PRESENT GND if CF1 installed 26 GND
2 B0D[11] 27 B0D[3]
3 B0D[12] 28 B0D[4]
4 B0D[13] 29 B0D[5]
5 B0D[14] 30 B0D[6]
6 B0D[15] 31 B0D[7]
7 B0CS1 32 B0CS0
8 -- 33 --
9 B0IORD 34 GND
10 B0IOWR 35 --
11 -- 36 --
12 B0INTRQ 37 --
13 +3.3V 38 +3.3V
14 GND 39 SCL
15 B0RSTS Reset master 40 SDA
16 B0RSTM Reset slave 41 --
17 B0IORDY 42 GND
18 B0DMARQ 43 B0A[2]
19 B0DMACK 44 B0A[1]
20 B0DASP 45 B0A[0]
21 B0PDIAG 46 B0D[0]
22 B0D[8] 47 B0D[1]
23 B0D[9] 48 B0D[2]
24 B0D[10] 49 B0IOCS16
25 GND 50 CF0PRESENT GND if CF0 installed



J2 - IDE (to the HDD)

IDE connector (to the ZIF-type 1.8" HDD)
Pin Signal Notes Pin Signal Notes
1 -- 2 --
3 B0RSTM 4 GND
5 B0D[7] 6 B0D[8]
7 B0D[6] 8 B0D[9]
9 B0D[5] 10 B0D[10]
11 B0D[4] 12 B0D[11]
13 B0D[3] 14 B0D[12]
15 B0D[2] 16 B0D[13]
17 B0D[1] 18 B0D[14]
19 B0D[0] 20 B0D[15]
21 GND 22 B0DMARQ
23 GND 24 B0IOWR
25 B0IORD 26 GND
27 B0IORDY 28 GND
29 B0DMACK 30 B0INTRQ
31 B0A[1] 32 B0PDIAG
33 B0A[0] 34 B0A[2]
35 B0CS0 36 B0CS1
37 B0DASP 38 +3.3V
39 +3.3V 40 --

Note: This connector uses 0.3mm flex cable, the HDD needs 0.2mm cable end.