Difference between revisions of "Load custom bitstream"
From ElphelWiki
(Created page with "==from u-boot== ==from OS== Category:393") |
|||
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | ==from u-boot== | + | ==Description== |
| − | == | + | The default bitstream is loaded from OS not from u-boot. |
| + | Reasons: | ||
| + | * Different banks have different (software - controlled and regulated) voltages and they need to be set up before loading. | ||
| + | ** voltages are set by the software through i2c | ||
| + | |||
| + | ==Bitstreams paths== | ||
| + | * ''/usr/local/verilog/'' | ||
| + | {| class='wikitable' | ||
| + | ! name | ||
| + | ! description | ||
| + | |- | ||
| + | |x393_parallel.bit | ||
| + | |for 5MPix sensor with parallel interface + SATA | ||
| + | |- | ||
| + | |x393_hispi.bit | ||
| + | |for 14MPix sensor with serial interface + SATA | ||
| + | |- | ||
| + | |x393_sata.bit | ||
| + | |SATA only | ||
| + | |- | ||
| + | |x359.bit | ||
| + | |for external MUX 3-to-1 board | ||
| + | |} | ||
| + | |||
| + | ==Init== | ||
| + | * /etc/init.d/init_elphel393 | ||
| + | ... | ||
| + | $CONFDIR/init_elphel393.py "{\"usb_hub\":1, \"ip\":1,\"imgsrv\":1, \"autoexp_daemon\":1, \"autocampars\":1, \"sata\":1, \"gps\":1, \"eyesis\":0 }" | ||
| + | ... | ||
| + | ** in this line the extra init procedures are listed, to disable/skip certain procedure set 0, to enable - set 1 | ||
| + | ** everything is done in ''/etc/elphel393/init_elphel393.py'' which runs other scripts. | ||
| + | ** the bitstream is loaded by '''autocampars''' or '''sata''' (if autocampars is skipped) | ||
| + | |||
| + | |||
| + | |||
[[Category:393]] | [[Category:393]] | ||
Revision as of 14:07, 20 April 2017
Description
The default bitstream is loaded from OS not from u-boot. Reasons:
- Different banks have different (software - controlled and regulated) voltages and they need to be set up before loading.
- voltages are set by the software through i2c
Bitstreams paths
- /usr/local/verilog/
| name | description |
|---|---|
| x393_parallel.bit | for 5MPix sensor with parallel interface + SATA |
| x393_hispi.bit | for 14MPix sensor with serial interface + SATA |
| x393_sata.bit | SATA only |
| x359.bit | for external MUX 3-to-1 board |
Init
- /etc/init.d/init_elphel393
...
$CONFDIR/init_elphel393.py "{\"usb_hub\":1, \"ip\":1,\"imgsrv\":1, \"autoexp_daemon\":1, \"autocampars\":1, \"sata\":1, \"gps\":1, \"eyesis\":0 }"
...
- in this line the extra init procedures are listed, to disable/skip certain procedure set 0, to enable - set 1
- everything is done in /etc/elphel393/init_elphel393.py which runs other scripts.
- the bitstream is loaded by autocampars or sata (if autocampars is skipped)
