Difference between revisions of "10393 power"
From ElphelWiki
(→Example setup and cables for 48V) |
(→Example setup and cables for 48V) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 30: | Line 30: | ||
==Powering from batteries== | ==Powering from batteries== | ||
===12V setup=== | ===12V setup=== | ||
| − | Power from any battery output voltage ranging 12-36V. | + | Power from any battery with output voltage ranging 12-36V. |
===48V setup=== | ===48V setup=== | ||
| − | Power from any battery output voltage ranging 18-75V. | + | Power from any battery with output voltage ranging 18-75V. |
===Example setup and cables for 48V=== | ===Example setup and cables for 48V=== | ||
| Line 45: | Line 45: | ||
File:10393 battery48v power cable.jpeg| Fig.7 Power cable | File:10393 battery48v power cable.jpeg| Fig.7 Power cable | ||
File:10393 battery48v 48-to-12v converter.jpeg| Fig.8 48-to-12v DC DC converter cable | File:10393 battery48v 48-to-12v converter.jpeg| Fig.8 48-to-12v DC DC converter cable | ||
| − | File:10393 battery48v 2.jpeg| Fig.9 | + | File:10393 battery48v 2.jpeg| Fig.9 48V power setup |
| − | File:10393 battery48v all connected.jpeg| Fig.10 | + | File:10393 battery48v all connected.jpeg| Fig.10 48V and extra 12V for something else |
</gallery> | </gallery> | ||
[[Category:393]] | [[Category:393]] | ||
Revision as of 13:45, 12 January 2018
Contents
18-75V (48V)
- camera's DC-DC converter installed: TRACO POWER THD 12-4810WI, IN 18-75V, OUT 3.3V/3500mA
Notes
- For 48V the recommended connector is J3 (accessible from the back panel)
9-36V (12V)
- camera's DC-DC converter installed: TRACO POWER THD 12-2410WI, IN 9-36V, OUT 3.3V/3500mA
Notes
- For 12V the recommended connector is J4 - bypassing diodes reduces voltage drop and the chances of not hitting the lower voltage limit are higher.
- For 18+ V the recommended connector is J3
Power supply requirements
AC/DC WALL MOUNT ADAPTER
- 20+ W
- 48V => 0.42+ A
- 12V => 1.67+ A
3.3V
- Without power board
 Fig.3 10393 (J1) and cable, see schematics |
Powering from batteries
12V setup
Power from any battery with output voltage ranging 12-36V.
48V setup
Power from any battery with output voltage ranging 18-75V.
Example setup and cables for 48V
- ANTY BATTERY 48V 4A (ANTY or BOOANT, can be found on AliExpress). Enough to power a single camera for several hours. See Fig.6.
- Power cable with an inline fuse and a switch, battery connector came with the battery, the outputs are 2.1mm plugs. Is used to power the camera. See Fig.7.
- Cable with a 48-to-12v converter (CUI INC PYB15-Q48-S12). It was used to power an extra network switch which might not be needed. See Fig.8.
- The camera was connected to a laptop running on its own battery.
Fig.6 Battery
Fig.7 Power cable
Fig.8 48-to-12v DC DC converter cable
Fig.9 48V power setup
Fig.10 48V and extra 12V for something else
