Difference between revisions of "10393 power"
From ElphelWiki
(→Options) |
|||
| Line 7: | Line 7: | ||
!Range | !Range | ||
!Power supply | !Power supply | ||
| + | !Power board | ||
|- | |- | ||
|align='left'|'''36-72V''' (default) | |align='left'|'''36-72V''' (default) | ||
| wall adapter (48V) | | wall adapter (48V) | ||
| + | | 10386 | ||
|- | |- | ||
|align='left'|'''18-75V''' | |align='left'|'''18-75V''' | ||
| wall adapter (48V) | | wall adapter (48V) | ||
| + | | 10385 | ||
|- | |- | ||
|align='left'|'''12-36V''' | |align='left'|'''12-36V''' | ||
| wall adapter, battery (12V) | | wall adapter, battery (12V) | ||
| + | | 10385 | ||
|- | |- | ||
|align='left'|'''3.3V''' | |align='left'|'''3.3V''' | ||
| direct, custom | | direct, custom | ||
| + | | None | ||
|} | |} | ||
| + | |||
==18-75V (48V)== | ==18-75V (48V)== | ||
* camera's DC-DC converter installed: TRACO POWER THD 12-4810WI, IN 18-75V, OUT 3.3V/3500mA | * camera's DC-DC converter installed: TRACO POWER THD 12-4810WI, IN 18-75V, OUT 3.3V/3500mA | ||
Latest revision as of 09:58, 4 September 2018
Contents
Options
| Range | Power supply | Power board |
|---|---|---|
| 36-72V (default) | wall adapter (48V) | 10386 |
| 18-75V | wall adapter (48V) | 10385 |
| 12-36V | wall adapter, battery (12V) | 10385 |
| 3.3V | direct, custom | None |
18-75V (48V)
- camera's DC-DC converter installed: TRACO POWER THD 12-4810WI, IN 18-75V, OUT 3.3V/3500mA
Notes
- For 48V the recommended connector is J3 (accessible from the back panel)
9-36V (12V)
- camera's DC-DC converter installed: TRACO POWER THD 12-2410WI, IN 9-36V, OUT 3.3V/3500mA
Notes
- For 12V the recommended connector is J4 - bypassing diodes reduces voltage drop and the chances of not hitting the lower voltage limit are higher.
- For 18+ V the recommended connector is J3
Power supply requirements
AC/DC WALL MOUNT ADAPTER
- 20+ W
- 48V => 0.42+ A
- 12V => 1.67+ A
3.3V
- Without power board
 Fig.4 10393 (J1) and cable, see schematics |
Powering from batteries
12V setup
Power from any battery with output voltage ranging 12-36V.
48V setup
Power from any battery with output voltage ranging 18-75V.
Example setup and cables for 48V
- ANTY BATTERY 48V 4A (ANTY or BOOANT, can be found on AliExpress). Enough to power a single camera for several hours. See Fig.7.
- Power cable with an inline fuse and a switch, battery connector came with the battery, the outputs are 2.1mm plugs. Is used to power the camera. See Fig.8.
- Cable with a 48-to-12v converter (CUI INC PYB15-Q48-S12). It was used to power an extra network switch which might not be needed. See Fig.9.
- The camera was connected to a laptop running on its own battery.
Fig.7 Battery
Fig.8 Power cable
Fig.9 48-to-12v DC DC converter cable
Fig.10 48V power setup
Fig.11 48V and extra 12V for something else
