Difference between revisions of "103692"
From ElphelWiki
| (One intermediate revision by the same user not shown) | |||
| Line 2: | Line 2: | ||
[[Image:103692_md.jpeg|frame|[[Media:103692.pdf|103692 Circuit Diagram, Parts List, PCB layout]] [[Media:103692_gerber.tar.gz|103692 Gerber files]]]] | [[Image:103692_md.jpeg|frame|[[Media:103692.pdf|103692 Circuit Diagram, Parts List, PCB layout]] [[Media:103692_gerber.tar.gz|103692 Gerber files]]]] | ||
103692 is an adapter board used with the [[10369]] board to connect ZIF-type 1.8" hard drive to the [[353 | Elphel Model 353 camera]]. | 103692 is an adapter board used with the [[10369]] board to connect ZIF-type 1.8" hard drive to the [[353 | Elphel Model 353 camera]]. | ||
| + | |||
| + | [[Image:Connect internal disk.jpeg|thumb|500px|1.8" HDD proper cable connection]] | ||
| + | |||
| + | === Notes === | ||
| + | <font color=red> | ||
| + | * It can be impossible to mount an external SATA disk to the camera with an internal 18"HDD (NC353L-369A-HDD) as the internal disk (Toshiba MK1214GAH) does not react on master/slave-option bus and also it doesn't tristate the signals it shares with the SATA bridge. | ||
| + | </font> | ||
=== Connectors === | === Connectors === | ||
Latest revision as of 13:40, 11 January 2010
Contents
103692 - Adapter board for ZIF-type 1.8" HDD
103692 is an adapter board used with the 10369 board to connect ZIF-type 1.8" hard drive to the Elphel Model 353 camera.
Notes
- It can be impossible to mount an external SATA disk to the camera with an internal 18"HDD (NC353L-369A-HDD) as the internal disk (Toshiba MK1214GAH) does not react on master/slave-option bus and also it doesn't tristate the signals it shares with the SATA bridge.
Connectors
J1 - to 10369 board
| Pin | Signal | Notes | Pin | Signal | Notes | |
|---|---|---|---|---|---|---|
| 1 | CF1PRESENT | GND if CF1 installed | 26 | GND | ||
| 2 | B0D[11] | 27 | B0D[3] | |||
| 3 | B0D[12] | 28 | B0D[4] | |||
| 4 | B0D[13] | 29 | B0D[5] | |||
| 5 | B0D[14] | 30 | B0D[6] | |||
| 6 | B0D[15] | 31 | B0D[7] | |||
| 7 | B0CS1 | 32 | B0CS0 | |||
| 8 | -- | 33 | -- | |||
| 9 | B0IORD | 34 | GND | |||
| 10 | B0IOWR | 35 | -- | |||
| 11 | -- | 36 | -- | |||
| 12 | B0INTRQ | 37 | -- | |||
| 13 | +3.3V | 38 | +3.3V | |||
| 14 | GND | 39 | SCL | |||
| 15 | B0RSTS | Reset master | 40 | SDA | ||
| 16 | B0RSTM | Reset slave | 41 | -- | ||
| 17 | B0IORDY | 42 | GND | |||
| 18 | B0DMARQ | 43 | B0A[2] | |||
| 19 | B0DMACK | 44 | B0A[1] | |||
| 20 | B0DASP | 45 | B0A[0] | |||
| 21 | B0PDIAG | 46 | B0D[0] | |||
| 22 | B0D[8] | 47 | B0D[1] | |||
| 23 | B0D[9] | 48 | B0D[2] | |||
| 24 | B0D[10] | 49 | B0IOCS16 | |||
| 25 | GND | 50 | CF0PRESENT | GND if CF0 installed |
J2 - IDE (to the HDD)
| Pin | Signal | Notes | Pin | Signal | Notes | |
|---|---|---|---|---|---|---|
| 1 | -- | 2 | -- | |||
| 3 | B0RSTM | 4 | GND | |||
| 5 | B0D[7] | 6 | B0D[8] | |||
| 7 | B0D[6] | 8 | B0D[9] | |||
| 9 | B0D[5] | 10 | B0D[10] | |||
| 11 | B0D[4] | 12 | B0D[11] | |||
| 13 | B0D[3] | 14 | B0D[12] | |||
| 15 | B0D[2] | 16 | B0D[13] | |||
| 17 | B0D[1] | 18 | B0D[14] | |||
| 19 | B0D[0] | 20 | B0D[15] | |||
| 21 | GND | 22 | B0DMARQ | |||
| 23 | GND | 24 | B0IOWR | |||
| 25 | B0IORD | 26 | GND | |||
| 27 | B0IORDY | 28 | GND | |||
| 29 | B0DMACK | 30 | B0INTRQ | |||
| 31 | B0A[1] | 32 | B0PDIAG | |||
| 33 | B0A[0] | 34 | B0A[2] | |||
| 35 | B0CS0 | 36 | B0CS1 | |||
| 37 | B0DASP | 38 | +3.3V | |||
| 39 | +3.3V | 40 | -- |
Note: This connector uses 0.3mm flex cable, the HDD needs 0.2mm cable end.
