Difference between revisions of "Sd boot rootfs"
From ElphelWiki
(Created page with "==Notes== * The micro SD card/adapter must be modified for this boot mode (to keep CD pin high with the card inserted) - only then the camera will boot. * EXT4 partition mounted ...") |
(→Format micro SD card (command line, can be done in the booted from NAND flash camera)) |
||
| (5 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
==Notes== | ==Notes== | ||
| − | * The micro SD card/adapter | + | |
| + | * The micro SD card/adapter has to be modified or the USB cable with appropriate host computer driver is needed to boot from the uSD card - see [[Tmp_manual#Boot]] for instructions. | ||
* EXT4 partition mounted as /. | * EXT4 partition mounted as /. | ||
| Line 11: | Line 12: | ||
** '''uImage''' | ** '''uImage''' | ||
** '''rootfs.tar.gz''' | ** '''rootfs.tar.gz''' | ||
| − | * Format into 2 partitions: FAT32 and EXT4 (use gparted or command line instructions below), the order of partitions is important or change bootargs in the device tree accordingly. | + | * Partition table: '''msdos''' ('''gpt''' won't work) Format into 2 partitions: FAT32 and EXT4 (use gparted or command line instructions below), the order of partitions is important or change bootargs in the device tree accordingly. |
* FAT32: copy the following files: | * FAT32: copy the following files: | ||
*** '''boot.bin''' | *** '''boot.bin''' | ||
| Line 25: | Line 26: | ||
* Insert, power on | * Insert, power on | ||
| − | ==Format micro SD card (command line)== | + | ==Format micro SD card (command line, can be done in the booted from camera's NAND flash)== |
| − | Example for '''/dev/ | + | Example for '''/dev/sdX''': |
| − | * create partitions with fdisk | + | * create partitions with fdisk , gparted or any other program: |
| − | * mkfs.vfat -F 32 /dev/ | + | ** the 1st partition is to be formatted to FAT32 - 1GB is more than enough |
| − | * mkfs.ext4 /dev/ | + | ** the 2nd partition is to be formatted to EXT4 - 2+GB |
| + | formatting with mkfs: | ||
| + | * mkfs.vfat -F 32 /dev/sdX1 | ||
| + | ---- | ||
| + | |||
| + | * mkfs.ext4 /dev/sdX2 | ||
[[Category:Elphel393]] | [[Category:Elphel393]] | ||
Latest revision as of 10:47, 12 January 2017
Contents
Notes
- The micro SD card/adapter has to be modified or the USB cable with appropriate host computer driver is needed to boot from the uSD card - see Tmp_manual#Boot for instructions.
- EXT4 partition mounted as /.
Prepare the card
PC:
- After all of the targets are built in poky use files from .../poky/build/tmp/deploy/images/elphel393/mmc/:
- boot.bin
- u-boot-dtb.img
- devicetree.dtb
- uImage
- rootfs.tar.gz
- Partition table: msdos (gpt won't work) Format into 2 partitions: FAT32 and EXT4 (use gparted or command line instructions below), the order of partitions is important or change bootargs in the device tree accordingly.
- FAT32: copy the following files:
- boot.bin
- u-boot-dtb.img
- devicetree.dtb
- uImage
- If EXT4 is not empty - format it or delete old contents
- Mount EXT4 to some <mountpoint>
- unpack the rootfs.tar.gz, console:
tar -C <mountpoint> -xzpf rootfs.tar.gz
Boot
- Insert, power on
Format micro SD card (command line, can be done in the booted from camera's NAND flash)
Example for /dev/sdX:
- create partitions with fdisk , gparted or any other program:
- the 1st partition is to be formatted to FAT32 - 1GB is more than enough
- the 2nd partition is to be formatted to EXT4 - 2+GB
formatting with mkfs:
- mkfs.vfat -F 32 /dev/sdX1
- mkfs.ext4 /dev/sdX2
