Eyesis assembly: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
===Step 1: Front Ends=== | == Head == | ||
=== Step 1: Head + Front Ends (already assembled and focused)<br> === | |||
{| | {| | ||
|[[Image:Eyesis sfe parts.jpeg | |- | ||
|[[Image:Eyesis sfe assembled.jpeg | | [[Image:Eyesis sfe parts.jpeg|thumb|300px]] | ||
| [[Image:Eyesis sfe assembled.jpeg|thumb|500px]] | |||
|} | |} | ||
*Connect cables to the Front Ends. | |||
===Step | *Put the front ends one by one into the head. | ||
* See Fig.1. There are 3 holes in the disk attached to the head bottom. The 1st hole is on the above of one of the 'eyes' and others are not - so it's easy to find it. | |||
* See Fig.2. Attach the part with main boards to the head (use thread-locker with these 3 screws). The cables from the marked sensors will go to the closest to the 1st hole board (on Fig.1,2 colors and eyes match) | === Step 2: Head + Boards === | ||
* Rotate the head counter clockwise (from 'hole 1' to 'hole 2') - attach the next 3 cables. | |||
* Remaining 3 cables go to the board near the 3rd hole. | *See Fig.1. There are 3 holes in the disk attached to the head bottom. The 1st hole is on the above of one of the 'eyes' and others are not - so it's easy to find it. | ||
*See Fig.2. Attach the part with main boards to the head (use thread-locker with these 3 screws). The cables from the marked sensors will go to the closest to the 1st hole board (on Fig.1,2 colors and eyes match) | |||
*Rotate the head counter clockwise (from 'hole 1' to 'hole 2') - attach the next 3 cables. | |||
*Remaining 3 cables go to the board near the 3rd hole. | |||
{| | {| | ||
|[[Image:Head boards 1.jpeg | |- | ||
|[[Image:Head boards 2.jpeg | | [[Image:Head boards 1.jpeg|thumb|400px]] | ||
| [[Image:Head boards 2.jpeg|thumb|350px]] | |||
|} | |} | ||
* Attach sync cables to the 10369 boards: | *Attach sync cables to the 10369 boards: | ||
Notes: | Notes: | ||
* The 1st board is the one near the 1st hole. | * The 1st board is the one near the 1st hole. | ||
| Line 25: | Line 34: | ||
{| | {| | ||
|[[Image:Sync cables.jpg | |- | ||
| [[Image:Sync cables.jpg|thumb|400px]] | |||
|} | |} | ||
== Box == | |||
{a schematic picture + photo}<br> | |||
== Eyesis == | |||
#Put a "cup" on the pole. | |||
#Connect the corresponding cables from the box (coming out of the pole) to the head {add a photo with comments} | |||
#Attach the head to the cup. | |||
#Choose the head orientation and tighten the "cup"'s 2 big screws. | |||
Latest revision as of 02:28, 1 December 2010
Head
Step 1: Head + Front Ends (already assembled and focused)
 |
 |
- Connect cables to the Front Ends.
- Put the front ends one by one into the head.
Step 2: Head + Boards
- See Fig.1. There are 3 holes in the disk attached to the head bottom. The 1st hole is on the above of one of the 'eyes' and others are not - so it's easy to find it.
- See Fig.2. Attach the part with main boards to the head (use thread-locker with these 3 screws). The cables from the marked sensors will go to the closest to the 1st hole board (on Fig.1,2 colors and eyes match)
- Rotate the head counter clockwise (from 'hole 1' to 'hole 2') - attach the next 3 cables.
- Remaining 3 cables go to the board near the 3rd hole.
 |
 |
- Attach sync cables to the 10369 boards:
Notes: * The 1st board is the one near the 1st hole. * J14 - cable foil up * J12, J13 - cable foil down * Better to start connecting with J14 side of the cable.
 |
Box
{a schematic picture + photo}
Eyesis
- Put a "cup" on the pole.
- Connect the corresponding cables from the box (coming out of the pole) to the head {add a photo with comments}
- Attach the head to the cup.
- Choose the head orientation and tighten the "cup"'s 2 big screws.