Talk:10359: Difference between revisions
No edit summary |
No edit summary |
||
| Line 23: | Line 23: | ||
09. '''fpcf -i2cw16 805 3''' - reset J4 DCM | 09. '''fpcf -i2cw16 805 3''' - reset J4 DCM | ||
===Write registers=== | |||
All the registers are 16 bit wide | |||
{| border="1" cellpadding="2" | |||
| Address | |||
| Bits/Values | |||
| Description | |||
|- | |||
| 0x801 | |||
| | |||
0x01 - "+" | |||
0x02 - "-" | |||
0x03 - reset small steps | |||
0x04 - "+90" | |||
0x08 - "-90" | |||
0x0c - reset quarter | |||
| system clock DCM | |||
|- | |||
| 0x802 | |||
| | |||
0x01 - "+" | |||
0x02 - "-" | |||
0x03 - reset small steps | |||
| SDRAM clock DCM | |||
|- | |||
| 0x803 | |||
| | |||
0x01 - "+" | |||
0x02 - "-" | |||
0x03 - reset small steps | |||
0x04 - "+90" | |||
0x08 - "-90" | |||
0x0c - reset quarter | |||
0x10,0x20 - add hact-data shift | |||
0x30 - reset hact-data shift | |||
| ch0 receive clock DCM | |||
|- | |||
| 0x804 | |||
| | |||
0x01 - "+" | |||
0x02 - "-" | |||
0x03 - reset small steps | |||
0x04 - "+90" | |||
0x08 - "-90" | |||
0x0c - reset quarter | |||
0x10,0x20 - add hact-data shift | |||
0x30 - reset hact-data shift | |||
| ch1 receive clock DCM | |||
|- | |||
| 0x805 | |||
| | |||
0x01 - "+" | |||
0x02 - "-" | |||
0x03 - reset small steps | |||
0x04 - "+90" | |||
0x08 - "-90" | |||
0x0c - reset quarter | |||
0x10,0x20 - add hact-data shift | |||
0x30 - reset hact-data shift | |||
| ch2 receive clock DCM | |||
|- | |||
| 0x806 | |||
| | |||
[2] - enable J4 (ch2) | |||
[1] - enable J3 (ch1) | |||
[0] - enable J2 (ch0) | |||
| switch direct channel | |||
|- | |||
| 0x807 | |||
| | |||
[1] - i2c bus select, 0 - sensors, 1 - CY22393 & EEPROM | |||
[2] - 10359 sensors clock source, 0 - from 10353, 1 - onboard generator CY22393 | |||
| system clock source / i2c bus select | |||
|} | |||
Revision as of 21:08, 1 May 2010
Sensors addresses
0x48 - broadcast 0x4a - J2 0x4c - J3 0x4e - J4
Initialization sequence
01. Apply clock to 10359
02. fpcf -i2cw16 807 2 - switch i2c bus to EEPROM & CY22393
03. fpcf -X 4 96 - switch internal 96MHz on the 10359
04. fpcf -i2cw16 807 1 - switch from the 10353's clock to the 10359's generated clock
05. fpcf -i2cw16 801 3 - reset system clock DCM
06. fpcf -i2cw16 802 3 - reset SDRAM clock DCM
07. fpcf -i2cw16 803 3 - reset J2 DCM
08. fpcf -i2cw16 804 3 - reset J3 DCM
09. fpcf -i2cw16 805 3 - reset J4 DCM
Write registers
All the registers are 16 bit wide
| Address | Bits/Values | Description |
| 0x801 |
0x01 - "+" 0x02 - "-" 0x03 - reset small steps 0x04 - "+90" 0x08 - "-90" 0x0c - reset quarter |
system clock DCM |
| 0x802 |
0x01 - "+" 0x02 - "-" 0x03 - reset small steps |
SDRAM clock DCM |
| 0x803 |
0x01 - "+" 0x02 - "-" 0x03 - reset small steps 0x04 - "+90" 0x08 - "-90" 0x0c - reset quarter 0x10,0x20 - add hact-data shift 0x30 - reset hact-data shift |
ch0 receive clock DCM |
| 0x804 |
0x01 - "+" 0x02 - "-" 0x03 - reset small steps 0x04 - "+90" 0x08 - "-90" 0x0c - reset quarter 0x10,0x20 - add hact-data shift 0x30 - reset hact-data shift |
ch1 receive clock DCM |
| 0x805 |
0x01 - "+" 0x02 - "-" 0x03 - reset small steps 0x04 - "+90" 0x08 - "-90" 0x0c - reset quarter 0x10,0x20 - add hact-data shift 0x30 - reset hact-data shift |
ch2 receive clock DCM |
| 0x806 |
[2] - enable J4 (ch2) [1] - enable J3 (ch1) [0] - enable J2 (ch0) |
switch direct channel |
| 0x807 |
[1] - i2c bus select, 0 - sensors, 1 - CY22393 & EEPROM [2] - 10359 sensors clock source, 0 - from 10353, 1 - onboard generator CY22393 |
system clock source / i2c bus select |