-
5. Now configure and compile a package. Default packages are compiled on the ''/usr/local''. If you want a different locati
3 KB (450 words) - 07:59, 6 December 2007
-
*Change the default application
*Configure the default application of the 10359
4 KB (517 words) - 00:53, 7 February 2011
-
channels must be in the range 1-8, default 2
jack-name, default "TimeMachine"
5 KB (681 words) - 06:38, 17 November 2009
-
...t-slash-init_env) in the top installation directory (called "elphel353" by default), one level above "fpga" one.
16 KB (2,550 words) - 14:33, 1 December 2017
-
1. Power on or reboot, then refresh (I'll use the default ip address of the camera)
sphase[i]=1(default) - channel 'i' latches Vact/Hact on the FALLING edge of sclk0, sphase[i]=0
23 KB (2,686 words) - 05:22, 31 October 2008
-
...e quickest way is to compile DNSMasq for Etrax (udhcpd is not installed by default), this will give you all what your 'clients' want. DNS, DHCP, etc. If you w
1 KB (238 words) - 23:21, 29 March 2009
-
...mera have a support of the streamer autostart. To use it, you need to open default web page on the camera (what is actually "camvc.html"), and make a setup of
1 KB (216 words) - 06:23, 3 March 2008
-
...rt of the image from one frame, and the other part - from the next one. In default configuration data from the sensor is continuously acquired to the memory a
1 KB (185 words) - 21:44, 13 October 2012
-
...at does not have any address, so a raw mode is used during I2C read/write. Default value after power up is 0xff (all bits "1").
...SATA_MASTER || if set to "0" SATA will be slave IDE device,<br/> with "1" (default) it is IDE master
22 KB (3,047 words) - 14:46, 20 January 2015
-
...after start but they will be updated as soon as recording has started. By default, the update period during recording is one second.
...of such naming scheme is shown on the screenshot of main window. This is a default scheme.
14 KB (2,145 words) - 12:34, 11 January 2017
-
...anually or using the script) you may get to the top working directory ( by default it is called "elphel353" and has subdirectories starting with "apps") and r
...'CVS' directory from the top directory of the project ('elphel353/CVS' by default), you do not need to remove CVS in subdirectories. Then re-run
11 KB (1,720 words) - 16:36, 17 March 2020
-
...ver in the root directory, http://192.168.0.9/ if you have not changed the default address.
2 KB (398 words) - 17:32, 30 May 2016
-
0 RGB24 (default)
4 KB (523 words) - 17:49, 19 September 2008
-
...is reachable using http://192.168.0.9/ my proposal would be to change the default to DHCP, with a timeout and zeroconf or fixed address. Next to this the cam
306 bytes (49 words) - 12:03, 5 September 2008
-
3. "Detect sensor on channel 0" (after configuration channel 0 is set by default).
3 KB (363 words) - 19:15, 6 December 2009
-
In installed the compiler to the default location at: /usr/local/cris/ so the command to compile the server is (for
'''*camera_ip*''' is - surprise - the IP of your camera (192.168.0.9 by default)
8 KB (1,216 words) - 03:16, 29 November 2008
-
telnet 192.168.0.9 #(If the default IP hasn't been changed. Or you can connect via 'ssh' using [http://www.chi
3 KB (438 words) - 11:09, 4 June 2012
-
card 0: default [USB AUDIO ], device 0: USB Audio [USB Audio]
3 KB (412 words) - 02:07, 23 November 2010
-
| By default, we install an IR-cut filter. At your request, we can remove the filter for
5 KB (741 words) - 09:23, 14 July 2020
-
...rmin.com/shop/shop.do?pID=6445#gps18 Garmin GPS18] is the model we sell by default with our GEO cameras.
856 bytes (134 words) - 09:45, 28 June 2010
