-
...to enable multicast. In unicast mode the camera only broadcasts the video if there is a client connection. Enabling multicast will mean that it is broad
If you want to add audio to your stream you just have to use a usb audio devic
3 KB (428 words) - 22:52, 8 June 2009
-
* This method is only recommended if the camera internal firmware is not fully operational (eg. network communic
* If the camera firmware is >8.0.7.4 it might be more convenient to use the came
2 KB (325 words) - 11:42, 16 January 2012
-
You can test if everything worked properly by opening a browser and going to:
If you get lots of xml output installation was successful.
2 KB (329 words) - 16:23, 19 April 2012
-
* If your camera is powered with the 48V (Midspan) power supply or equivalent ma
* If you have a 12-36V DC modified camera you received the power injector adapte
3 KB (441 words) - 01:42, 7 February 2011
-
=If you are new to GNU / Linux=
If you get some problems it is very useful to copy the error message that syst
21 KB (3,230 words) - 14:31, 4 June 2018
-
2. Press ''Get Previews'' button (it is ok if the images are cut from the bottom - it's the browser problem - just press
* Make a test <font color=red>RECORD/STOP</font> to check if all HDDs are present (the default RECORD delay is set to 5 seconds, so wait
6 KB (874 words) - 14:27, 15 June 2011
-
...abase for each camera built. That will help to restore the bad block table if accidentally erased by our developers or users;
2 KB (278 words) - 23:57, 17 March 2007
-
If you want to apply for sponsored hardware please add your project with a sho
2 KB (327 words) - 18:25, 28 November 2011
-
...o reduce the bandwidth more we need to utilize selective block encoding so if camera is looking at an empty hallway there would be no bitstream at all bu
..., embedded MPlayer video plugin and other fancy features. It would be nice if you could create something like that with regular web development tools, bu
14 KB (2,226 words) - 20:58, 17 September 2008
-
maybe (if you haven't already implemented) it will be usefull putting a small led tha
7 KB (1,054 words) - 15:52, 30 June 2008
-
if [ -s $img ] ; then
if [ -s "$OUTFILE" ] ; then
2 KB (193 words) - 07:23, 15 June 2007
-
...ither earlier assigned MAC address (written in bootblock of the flash) or, if it is a brand new camera, temporary use random MAC address. Next step - run
...be used to read flash from the camera for postmortem analysis of the data if camera does not boot for some reason.
7 KB (1,207 words) - 16:19, 20 June 2009
-
Quality of image may be better if we include a manual iris to have more depth in the picture.
12 KB (1,769 words) - 09:59, 24 October 2018
-
...utton was pressed, do not attempt to reboot (it will fail or reflash again if the future bulk-flash daemon is still running) but just output message inst
It takes longer time to connect to the camera if the IP during netboot is the same as during normal boot, but MAC addresses
2 KB (280 words) - 23:51, 29 September 2007
-
...rd, so no 2 0xff bytes can appear together - this fact is used to find out if the data in the circular buffer was overwritten by the newer image frames.
...ligning them to the end of the 32-byte chunk, adding zeros before the data if needed. The last 4 bytes contain a 24-bit byte length of the JPEG data with
18 KB (2,955 words) - 00:26, 1 December 2007
-
...ar/state/exif.template'' is read in only once - at the imgsrv start up. So if you want to modify the Exif data attached to the camera images, you will ne
2 KB (319 words) - 00:05, 11 October 2007
-
...become available (it is possible that no waiting will actually take place if the image acquisition is ahead of the reading images out process. As far as
If issued with empty arguments (just <nowiki>http://<camera_ip>:8081/</nowiki>
9 KB (1,584 words) - 12:42, 27 January 2017
-
...ogram (0x200-0x27f for odd/all exposures, 0x280-0x2ff - for even ones) and if it is empty - programs default sequence (will not change existent sequence)
...to process the incoming sensor data you do not need to use ccam.cgi - only if any of the parameters above need to be changed, Later we'll develop new sof
13 KB (2,170 words) - 13:21, 30 October 2008
-
1852 if ((vp=paramValue(gparams, "iq"))) ioctl(devfd, _CCCMD(CCAM_WPARS , P_QUALI
...make this value as close as possible to the one specified by application, if the application passed the invalid value driver will use the corrected one.
6 KB (980 words) - 00:43, 17 October 2007
-
...rent cable length you may see image that looks like monochrome or purple - if the pixels are sampled at wrong time, red and green (also green and blue) p
Open the following URL in the browser (replace 192.168.0.9 if camera has different IP):
9 KB (1,508 words) - 15:06, 1 May 2022
