Difference between revisions of "Eyesis4Pi User Guide - Recording"

From ElphelWiki
Jump to: navigation, search
m (→‎Power On)
 
(35 intermediate revisions by the same user not shown)
Line 1: Line 1:
−
==Package==
+
== Download ==
−
* Eyesis4Pi
+
<font size='2'>
−
* Switch 3CRDSF9PWR
+
The GUI for recording is installed on the Eyesisbox PC by default.
−
* PC
 
  
−
==Quick Start==
+
There are several ways to install a newer version:
−
* Turn the switch on.
+
 
−
<br/><hr/>
+
Terminal:
−
* Connect the camera's ethernet cables to the PoE enabled ports. Eyesis4Pi's default IP addresses:
+
cd <any-path>
−
<font size=2>
+
git clone git://elphel.git.sourceforge.net/gitroot/elphel/eyesis4pi_gui (initial checkout)
−
  192.168.0.221-228
+
git pull (update)
 +
SF.net:
 +
  http://elphel.git.sourceforge.net/git/gitweb.cgi?p=elphel/eyesis4pi_gui;a=tree
 
</font>
 
</font>
−
<br/><hr/>
+
 
−
* Connect the PC to the Gigabit port of the switch.
+
Follow the instructions in INSTALL.txt:
−
'''''Note:''' Do not confuse the Gigabit port with the Console port.''
+
1. Install the following packages, terminal:
−
<br/><hr/>
+
  sudo apt-get install php5 apache2
−
* Configure the PC's network settings:
+
−
<font size=2>
+
2. Make the src folder visible to the web server:
−
  IP address: 192.168.0.xxx (example, 192.168.0.68)
+
2a. Create a link, terminal: "sudo ln -sf <path-to-eyesis4pi_gui-folder> /var/www/eysisgui"
 +
2b. Or copy all the files to /var/www/eyesisgui.
 +
Note: "/var/www" is the (apache2) web server's document root folder.
 +
 +
3. Make the footage root folder "/data/footage" writable for everyone.
 +
 
 +
 
 +
== Equipment/Package ==
 +
 
 +
*Eyesis4Pi
 +
*Switch
 +
*PC / Laptop
 +
 
 +
<br> <br>
 +
 
 +
== Power On ==
 +
 
 +
*Turn the switch on.
 +
*Connect the camera's ethernet cables to the power enabled ports. The camera boot takes about 1 min.
 +
<font size='2'><b>
 +
Important Notice: Use a fan to cool the camera's pole when shooting indoors.
 +
</b></font>
 +
<br> <br>
 +
 
 +
== Network Set Up ==
 +
 
 +
*Connect the PC to the Gigabit port of the switch.
 +
*Configure the PC's network settings ([http://linuxlibrary.org/kubuntu-network-configuration/ Kubuntu Network Configuration Guide]):
 +
 
 +
<font size="2"></font>
 +
 
 +
<font size="2">
 +
  IP address: 192.168.0.68 (example)
 
  Mask:      255.255.255.0
 
  Mask:      255.255.255.0
 
</font>
 
</font>
−
<br/><hr/>
+
 
−
* Open the GUI page (the address is bookmarked in the Firefox and in the Chrome). The GUI address is:
+
<font size="2"></font> '''''Note:''' Eyesis4Pi's default IP addresses: 192.168.0.221-229'' <br> <br>  
−
<font size=2>
+
 
 +
== System Tests ==
 +
 
 +
*Open the GUI page (the address is bookmarked in the Firefox and in the Chrome). The GUI address is:
 +
 
 +
<font size="2"></font>
 +
 
 +
<font size="2">
 
  http://127.0.0.1/eyesisgui/index.html
 
  http://127.0.0.1/eyesisgui/index.html
 
</font>
 
</font>
−
<br/><hr/>
+
 
−
* Go to the "Settings" -> "Test"-tab:
+
<font size="2"></font>  
−
====System tests====
+
 
−
=====1. All the modules are online=====
+
{|
−
Check the '''Temperatures Map''' under '''Other''' tab. If there are 0 black rectangles then all the modules are working.
+
|- valign="top"
−
=====2. Images=====
+
| [[Image:Recording gui settings.jpeg|thumb|500px]]
−
Go to the Camera tab, press jpeg button and turn on the test pattern. Then refresh Previews. The correct test pattern will consist from the following tiles:
+
|}
 +
 
 +
*Go to the "Settings" -&gt; "Test"-tab:
 +
 
 +
*Follow the '''Open the test page'''-link, the tests are:
 +
 
 +
<font size="2"></font>
 +
 
 +
<font size="2">
 +
1. All the modules are online.
 +
2. GPS locked
 +
3. IMU detected
 +
4. Internal CF cards are present
 +
</font>
 +
 
 +
<font size="2"></font> <!--
 +
{|
 +
|-
 +
|[[File:Other tab.jpeg|400px|thumb|Fig.2 Other-tab]]
 +
|}
 +
{|
 +
|-
 +
|[[File:Eyesis4pi test pattern.jpeg|600px|thumb|Fig.3 Eyesis4Pi Test Pattern]]
 +
|}
 +
{|
 +
|-
 +
|[[File:Gps coords.jpeg|400px|thumb|Fig.4 GPS coordinates]]
 +
|}
 
{|
 
{|
 
|-
 
|-
−
|[[File:Test_pattern.jpeg]]
+
|[[File:Cf cards.jpeg|thumb|Fig.5 CF cards]]
 
|}
 
|}
 +
--> <br> <br>
 +
 +
== Setting recording parameters: storage paths ==
 +
 +
*Check paths at the '''Settings''' -&gt; '''Recording'''-tab
 +
 +
<font size="2"></font>
 +
 +
<font size="2">
 +
'''Absolute footage path''' - the path to the folder where all the footage series are stored. '''Must be writable to everyone.'''
 +
'''Series subfolder''' - created automatically
 +
'''Files limit in a subfodler''' - number of files stored in a subfolder inside '''Series subfolder'''
 +
 +
'''CF card device name''' - GPS/IMU log is saved to the internal CF cards. On the master camera they are /dev/hda1 &amp; /dev/hdb1
 +
'''GPS/IMU log file name''' - absolute path (in the master camera)+ log base name
 +
'''Starting index''' - logs are named as follows - '''[base_name]-[index]'''
 +
'''Records per file''' - number of records per log file. New file: an incremented index is added to the base name.
 +
</font>
 +
 +
<font size="2"></font>
 +
 +
{|
 +
|-
 +
| [[Image:Recording tab.jpeg|thumb|500px]]
 +
|}
 +
 +
<br><br>
 +
 +
== Setting recording parameters: camera settings ==
 +
 +
*Check camera settings at the '''Settings''' -&gt; '''Camera'''-tab
 +
 +
<font size="2"></font>
 +
 +
<font size="2">
 +
'''Trigger period,ms ''' - 1/FPS.
 +
'''Skip frames mask''' - hex 0x1ff - bit[8]=enable, bits[7:0] - '''1''' - record frame, '''0''' - skip frame - in an 8-frame sequence.
 +
'''HDRVexpos''' - in the HDR mode - the darker frame multiplication coefficient to get exposure for the lighter frame.
 +
'''AutoExp max, ms''' - the autoexposure value limit.
 +
'''AutoExp level''' - value of a pixel at which the autoexposure works.
 +
'''AutoExp fracpix''' - number of pixels below the Autoexp level.
 +
'''AutoExp frame ahead''' - number of previous frames used for calculatin the current frame exposure.
 +
'''Compression quality''' - JP4/JPEG compression quality.
 +
 +
'''HDR mode''' - at the fps rate the dark and the bright images alternate.
 +
 +
'''Skip Frames Mask''':
 +
  0x1ff - frames are not skipped, camera is triggered at '''Trigger period'''.
 +
  0x155 - the camera is triggered at '''Trigger period'''/2 but only every other frame is recorded. It makes autoexposure adapt quicker and in the '''HDR mode''' records only normally exposed images skipping the underexposed ones.
 +
 +
Recommended values for 1 fps:
 +
'''Trigger period''' = 1000 (ms)
 +
'''Skip Frames Mask''' = 0x155
 +
'''HDR mode''' = '''On'''
 +
</font>
 +
 +
<font size="2"></font>
 +
 +
{|
 +
|-
 +
| [[Image:Camera tab.jpeg|thumb|500px]]
 +
|}
 +
 +
<br><br>
 +
 +
== Recording ==
 +
 +
*'''Record'''-button to start recording
 +
 +
{|
 +
|-
 +
| [[Image:Rec.jpeg|thumb|300px]]
 +
|}
 +
 +
<br><br>
 +
 +
== Stopping ==
 +
 +
*'''Stop'''-button for stop.
 +
 +
{|
 +
|-
 +
| [[Image:Rec.jpeg|thumb|300px]]
 +
|}
 +
 +
<br><br>
 +
 +
== Downloading IMU/GPS Log ==
 +
 +
*After stopping - go to the '''Settings''' -&gt; '''Recording'''-tab to download the IMU/GPS log.
 +
 +
<br><br>
 +
 +
== Checking the Recorded Footage ==
 +
 +
*Check the footage at the '''Absolute footage path''' - each panorama set should consist of 9 images named with a timestamp of when it was taken plus the index of the camera (seconds_microseconds_index.jp4):
 +
 +
{|
 +
|-
 +
| [[Image:Footage folder structure.jpeg|thumb|300px|Footage folder structure.jpeg]]
 +
|}
 +
 +
'''''Note:''' Missing files most likely means that the FPS is too high''.
 +
 +
== Links ==
 +
 +
*[[Elphel Eyesis4Pi|Eyesis4Pi Main Article]]
 +
*[[Eyesis4Pi workflow|Workflow]]
 +
*[[Eyesis4Pi User Guide|User Guide - Recording]]
 +
*[[Eyesis4Pi Footage Procedures page|User Guide - Post-Processing: Footage Procedures]]
 +
*[[Eyesis4pi Post-Processing|User Guide - Post-processing: ImageJ]]
 +
*[[Eyesis4Pi data structure|Data Structure Description]]
 +
*[[Eyesis4Pi Calibration|Calibration Process]]
 +
[[Category:Eyesis4Pi]]
 +
[[Category:User Guide]]

Latest revision as of 11:41, 11 March 2013

Download

The GUI for recording is installed on the Eyesisbox PC by default.

There are several ways to install a newer version:

Terminal: 

cd <any-path>
git clone git://elphel.git.sourceforge.net/gitroot/elphel/eyesis4pi_gui (initial checkout)
git pull (update)

SF.net: 

http://elphel.git.sourceforge.net/git/gitweb.cgi?p=elphel/eyesis4pi_gui;a=tree

Follow the instructions in INSTALL.txt: 

1. Install the following packages, terminal:
 sudo apt-get install php5 apache2

2. Make the src folder visible to the web server:
2a. Create a link, terminal: "sudo ln -sf <path-to-eyesis4pi_gui-folder> /var/www/eysisgui"
2b. Or copy all the files to /var/www/eyesisgui.
Note: "/var/www" is the (apache2) web server's document root folder.

3. Make the footage root folder "/data/footage" writable for everyone.


Equipment/Package

  • Eyesis4Pi
  • Switch
  • PC / Laptop



Power On

  • Turn the switch on.
  • Connect the camera's ethernet cables to the power enabled ports. The camera boot takes about 1 min.

Important Notice: Use a fan to cool the camera's pole when shooting indoors.



Network Set Up

IP address: 192.168.0.68 (example)
Mask:       255.255.255.0

Note: Eyesis4Pi's default IP addresses: 192.168.0.221-229

System Tests

  • Open the GUI page (the address is bookmarked in the Firefox and in the Chrome). The GUI address is:

http://127.0.0.1/eyesisgui/index.html

Recording gui settings.jpeg
  • Go to the "Settings" -> "Test"-tab:
  • Follow the Open the test page-link, the tests are:

1. All the modules are online.
2. GPS locked
3. IMU detected
4. Internal CF cards are present



Setting recording parameters: storage paths

  • Check paths at the Settings -> Recording-tab

Absolute footage path - the path to the folder where all the footage series are stored. Must be writable to everyone.
Series subfolder - created automatically
Files limit in a subfodler - number of files stored in a subfolder inside Series subfolder

CF card device name - GPS/IMU log is saved to the internal CF cards. On the master camera they are /dev/hda1 & /dev/hdb1
GPS/IMU log file name - absolute path (in the master camera)+ log base name
Starting index - logs are named as follows - [base_name]-[index]
Records per file - number of records per log file. New file: an incremented index is added to the base name.

Recording tab.jpeg



Setting recording parameters: camera settings

  • Check camera settings at the Settings -> Camera-tab

Trigger period,ms  - 1/FPS.
Skip frames mask - hex 0x1ff - bit[8]=enable, bits[7:0] - 1 - record frame, 0 - skip frame - in an 8-frame sequence.
HDRVexpos - in the HDR mode - the darker frame multiplication coefficient to get exposure for the lighter frame.
AutoExp max, ms - the autoexposure value limit.
AutoExp level - value of a pixel at which the autoexposure works.
AutoExp fracpix - number of pixels below the Autoexp level.
AutoExp frame ahead - number of previous frames used for calculatin the current frame exposure.
Compression quality - JP4/JPEG compression quality.

HDR mode - at the fps rate the dark and the bright images alternate.

Skip Frames Mask: 
  0x1ff - frames are not skipped, camera is triggered at Trigger period.
  0x155 - the camera is triggered at Trigger period/2 but only every other frame is recorded. It makes autoexposure adapt quicker and in the HDR mode records only normally exposed images skipping the underexposed ones.

Recommended values for 1 fps:
Trigger period = 1000 (ms)
Skip Frames Mask = 0x155
HDR mode = On

Camera tab.jpeg



Recording

  • Record-button to start recording
Rec.jpeg



Stopping

  • Stop-button for stop.
Rec.jpeg



Downloading IMU/GPS Log

  • After stopping - go to the Settings -> Recording-tab to download the IMU/GPS log.



Checking the Recorded Footage

  • Check the footage at the Absolute footage path - each panorama set should consist of 9 images named with a timestamp of when it was taken plus the index of the camera (seconds_microseconds_index.jp4):
Footage folder structure.jpeg

Note: Missing files most likely means that the FPS is too high.

Links

Retrieved from "https://wiki.elphel.com/index.php?title=Eyesis4Pi_User_Guide_-_Recording&oldid=12867"