Difference between revisions of "Using 10359 mux with 10393"

Revision as of 16:22, 17 November 2017

Setup

Firmware image

20171115 or required apps-autocampars version is at least 1.0.47

root@elphel393:~# cat /etc/elphel393/packages/apps-autocampars 
1.0.47

Connection

Fig.1 10393 ports

• cable sides as described here
• a mux board can be connected to any sensor port
• up to 4x mux boards at the same time (up to 4x do not require extra power modifications if 10389 is not connected)
• sensor boards can be connected to any unused ports

Fig.2 10359 mux board (older revision)

• if the number of connected mux boards is 4 and 10389+SSD then extra power is needed:

quick mod: see Fig.2
lift pins 3,4 on J1, put teflon tape under them and solder a wire to those lifted pins connected. Then add a MOS transistor or a switch that will apply external 3.3 V to W2 when those J1.3, J1.4 have 
power.

Modified device tree

Download and use this devicetree.dtb. The easiest way is to overwrite the device tree on the BOOT partition of a recovery SD card and then boot from it.

Application mask (assuming 10389 is not connected)

Without the 10389 the application mode is set in /etc/elphel393/default_10389.xml

root@elphel393:~# cat /etc/elphel393/default_10389.xml 
<?xml version="1.0" standalone="yes"?>
<board>
        <model>10389 not present</model>
        <rev>B</rev>
        <serial>F80000</serial>
        <app>MT9P006</app>
        <mode>15</mode>
</board>

To edit on the camera, use nano:

ssh root@192.168.0.9
root@elphel393:~# nano /etc/elphel393/default_10389.xml

To enable programming mux board(s) - set corresponding bits in [19:16]=0x?, [15:0]=0x7777 - then convert to decimal. Examples:

• mux on port 0 (bit 16):

<mode>96119</mode>  (=0x17777)

• mux on port 3 (bit 19):

<mode>554871</mode> (=0x87777)

• 2 mux boards on port 1 & 2:

<mode>423799</mode> (=0x67777)

Then

root@elphel393:~# sync
root@elphel393:~# reboot -f

Phase adjustments

• For each port with incorrect sensor phase. A quick link for port 0:

http://192.168.0.9/parsedit.php?sensor_port=0&TESTSENSOR&SENSOR_PHASE&MULTI_PHASE1&MULTI_PHASE2&MULTI_PHASE3

TESTSENSOR - test pattern mode
SENSOR_PHASE - mux or single sensor phase
MULTI_PHASE1 - mux port 0 (J2)
MULTI_PHASE2 - mux port 1 (J3)
MULTI_PHASE3 - mux port 2 (J4)

• • inspect image
  • TESTSENSOR=0x10008 - color bars mode, see Fig.3
  • MULTI_PHASE1=0x10000 (this worked for the tested setup)
  • MULTI_PHASE2=0x10000
  • MULTI_PHASE3=0x10050

Fig.3 Test pattern

Note: I had a script somewhere for auto adjustment

• Save configuration (for port 0):

http://192.168.0.9/autocampars.php?sensor_port=0

More details

device tree

• decompile device tree

~$ dtc -I dtb -O dts -o devicetree.dts devicetree.dtb

• the only change that is made to work with the mux board is:

-elphel393-detect_sensors,port-mux = "none none none none";
+elphel393-detect_sensors,port-mux = "detect detect detect detect";

• compile device tree

~$ dtc -I dts -O dtb -o devicetree.dtb devicetree.dts

if 10389 is connected

Go to http://community.elphel.com/bootblock393/ and program 10389 EEPROM

• Enter camera's IP address in the 1st block (top-left)
• In the 2nd block:
  • Read AUX
  • Set

Application = MT9P006
Application mode = as described for 10389-less setup

• • Program AUX
• Reboot