-
Default IP: 192.168.0.9
Just installing new Java flavours does not change the default Java pointed to by /usr/bin/java. You must explicitly set this:
2 KB (329 words) - 16:23, 19 April 2012
-
* The camera comes with default IP 192.168.0.9, make sure your connected computer has an IP address from th
* By default the streamer daemon is set to auto-start when you boot your camera. Make su
3 KB (441 words) - 01:42, 7 February 2011
-
By default the camera will stream as fast as possible which may not be
specified in megahertz. The default and maximum sensor clock is 48 MHz.
5 KB (762 words) - 06:58, 18 May 2007
-
Now uninstall the default Ubuntu's mplayer and mencoder & install the created package:
answer by default (enter, enter, ...)
21 KB (3,230 words) - 14:31, 4 June 2018
-
...e 192.168.0.xx1,192.168.0.xx2,192.168.0.xx3). Other parameters can be left default. After camogms are started the "Camogm Status" will indicate that with a st
...t <font color=red>RECORD/STOP</font> to check if all HDDs are present (the default RECORD delay is set to 5 seconds, so wait until camogm state becomes "runni
6 KB (874 words) - 14:27, 15 June 2011
-
Here is a simple gst-pipeline to record camera live stream and PC's default audio input to a Theora / Vorbis OGG file:
466 bytes (59 words) - 10:33, 24 January 2010
-
* [-d ethX] - network interface to camera, by default, eth0
* ip=xxx.xxx.xxx.xxx - ip for camera (by default, 192.168.0.9)
7 KB (1,207 words) - 16:19, 20 June 2009
-
# TRIG - Switch from free-running-mode(default) to triggered mode:TRIG_CONDITION=0x0, set the TRIG_PERIOD, TRIG=0x4
3 KB (557 words) - 09:18, 23 January 2012
-
...= new long[4]; /** now not used, was scale _after_ gamma is applied, 0x400(default) corresponds to 1.0 */
6 KB (1,003 words) - 12:34, 12 November 2010
-
*'''CIRCLSEEK_LAST''' - move pointer to the last acquired frame (default after open). It is similar to a combination of CIRCLSEEK_PREV after CIRCLSE
18 KB (2,955 words) - 00:26, 1 December 2007
-
...ervers ([http://www.boa.org Boa], included with Axis SDK, currently on the default port 80 in camera and [http://www.lighttpd.net/ lighttpd] - now used in Elp
Default imgsrv ports are '''2323, 2324, 2325 and 2326''' instead of single '''8081'
9 KB (1,584 words) - 12:42, 27 January 2017
-
With default camera ip of 192.168.0.9 it will look like:
1 KB (214 words) - 13:13, 12 April 2012
-
.../all exposures, 0x280-0x2ff - for even ones) and if it is empty - programs default sequence (will not change existent sequence). Mechanical shutter sequencer
13 KB (2,170 words) - 13:21, 30 October 2008
-
The phase default settings in the camera are optimized for a short cable (30 to 50mm), for lo
...ext 2 bits - 90-degrees additional shift, higher bits are "don't care". In default configuration bit 18 (0x40000) is set, because only non-zero values change
9 KB (1,508 words) - 15:06, 1 May 2022
-
...ggered mode you need to set "Program ahead" parameter to 5 instead of it's default value - 3. If not the camera freeze after the first frame.
935 bytes (148 words) - 06:44, 19 July 2010
-
* fixed TTL on RTSP session in astreamer. Defined as default 64 --[[User:Landy|Landy]] 12:48, 5 May 2009 (CDT)
...MDI_MODE=mdix" for cross, or any other (ot w/o this string) - for auto, by default--[[User:Spectr|Spectr]] 08:43, 21 March 2008 (CDT)
32 KB (4,592 words) - 16:14, 26 September 2014
-
...er IP/directory in the GET request as well as the script name. Script uses default values if the parameters ("NFS=" and "SCRIPT=") are not specified.
...pt on NFS server. After that response camera normally (while executing the default nfs_update script) shuts down web server, writes to flash memory and reboot
1 KB (216 words) - 01:18, 22 April 2009
-
...ent. The new file will be started if this time limit will be exceeded. The default duration is 60 seconds, current value is reported by status/xstatus command
...file segment. The new file will be started if this limit is exceeded. The default value is 16384.
24 KB (3,768 words) - 14:39, 11 July 2021
-
...work streaming require a proper network configuration. Here is the list of default settings and some hacks you can do.
== Default config ==
4 KB (575 words) - 16:13, 24 October 2018
-
...or their subdirectories) in the camera. Examples below assume you have the default camera IP='''192.168.0.9''':
...s as you can change the installed files and rebooting will not restore the default behaviour. Flash memory has limited number of write cycles and can develop
36 KB (5,115 words) - 06:00, 8 February 2012
